Manuale d’uso / di manutenzione del prodotto CCZ196AT del fabbricante Magnavox
Vai alla pagina of 64
Owner’s Manual Important! Return your Warranty Registration Card within 10 days. See why inside. Color TV with built-in VCR CCZ196AT CCZ196comb.QX33 4/6/99 7:04 PM Page 1.
Once your PHILIPS MAGNAVOX purchase is registered, you’re eligible to receive all the privileges of owning a PHILIPS MAGNAVOX product. So complete and return the Warranty Registration Card enclosed with your purchase at once. And take advantage of these important benefits.
Introduction 3 Features • A-B Repeat Play • Automatic Channel Setup • Automatic Operation Features • Automatic Tracking Adjustment • Closed Caption • Daylight-Saving Time • High Quality .
4 Table of Contents Setting Up Your TV/VCR Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
• The remote control and its batteries are supplied. • Do not mix alkaline and man- ganese batteries. • Do not mix old and new batteries. Before Using the TV/VCR 5 Putting Batteries in the Remote Control 1 Remove the battery compartment lid on the bottom of the remote control by pressing in the tab and lifting the lid.
6 Hooking Up The TV/VCR ANT. ANT. L R AUDIO IN VIDEO IN Hooking Up Your TV/VCR With a Cable Signal or Outdoor Antenna ANT. L R AUDIO IN VIDEO IN IN OUT ANT. Connect an RF coaxial cable (75- ohm, not supplied) to the OUT Jack on the Cable Box and to the ANT(enna) Jack on the TV/VCR.
Hooking Up The TV/VCR (cont’d) 7 ANT. L R AUDIO IN VIDEO IN CH3 CH4 OUT IN ANT R L VIDEO IN OUT IN OUT AUDIO VIDEO IN AUDIO IN L R ANT. • Before connecting an antenna or cable signal to the ANT(enna) Jack, make sure the pin is not bent.
8 Turning On the TV/VCR Before you turn on the TV/VCR, make sure there are batteries in the remote control and the TV/VCR is hooked up correctly. The instructions on this page work only when you turn on the TV/VCR for the first time. 1 Press the POWER button.
Language Selection 9 Follow the steps below to change the language of the on-screen displays and menus. 3 Press the PLAY/ ▲ button or the STOP/ ▼ button to choose SELECT LANGUAGE. Then, press the F.FWD/ B button. 4 Press the PLAY/ ▲ button or the STOP/ ▼ button to select ENGLISH or ESPAÑOL (Spanish).
10 Automatic Channel Setup Although the TV/VCR may automatically memorize the channels you receive when you turn it on for the first time, you may set up channels again by following the steps below. 1 Press the COMBI button, then press the MENU button.
Automatic Channel Setup (cont’d) 11 4 Press the F.FWD/ B button or the REW(ind)/ { button to select SAVED (to add that channel) or DELETED (to delete that channel). 5 Press the STATUS/EXIT button. Programming of the channel you added or deleted will appear.
12 Setting the Clock • Entries that do not match the TV/VCR’s calendar will cause a question mark (?) to appear on the screen. • To make corrections while you are setting the clock, press the CLEAR button until the space for the num- ber you want to correct is flashing.
Setting the Clock (cont’d) 13 5 Press two Number buttons for the hour(s) and two Number buttons for the minute(s). Then press 1 for AM or 2 for PM. For example, for 9:30 PM, press 09, 30, 2.
14 Setting the Clock (cont’d) Automatic PBS Channel Selection 4 If ON appears beside AUTO CLOCK, press the MENU button. If OFF appears beside AUTO CLOCK, press the F.FWD/ B button so that ON appears to the right of AUTO CLOCK, then press the MENU button.
Setting the Clock (cont’d) 15 7 When the TV/VCR finds the PBS channel, the time will appear on-screen. Press the STATUS/EXIT button. 6 NOW SEARCHING flashes on the TV/VCR screen. However, you may see the message: “PLEASE TURN OFF TO SET AUTO CLOCK PLEASE WAIT SEVERAL MINUTES.
16 Setting the Clock (cont’d) Manual PBS Channel Selection 4 If ON appears beside AUTO CLOCK, press the MENU button. If OFF appears beside AUTO CLOCK, press the F.FWD/ B button so that ON appears to the right of AUTO CLOCK, then press the MENU button.
Setting the Clock (cont’d) 17 8 When the TV/VCR finds the clock data, the time will appear on-screen. Press the STATUS/EXIT button. 6 Use the Number buttons to select your PBS station. If you make a mistake, press the CLEAR button, then enter the correct number.
18 Daylight-Saving Time 5 2-4 4 Press the PLAY/ ▲ button or the STOP/ ▼ button to select DAYLIGHT SVG.TIME. Then, press the F.FWD/ B button so that ON or OFF appears beside DAYLIGHT SVG. TIME (Daylight Saving Time). 5 Press the STATUS/EXIT button.
Time Zone 19 • If you select AUTO at step 5, the TV/VCR will set the clock according to the time zone data of the PBS station it finds. • You cannot select SET TIME ZONE at step 4 if AUTO CLOCK is set to OFF. Helpful Hints 5 Press the PLAY/ ▲ button or the STOP/ ▼ button to select a time zone.
2 Find your code. 20 Setting the Remote to Operate a Cable Box/DBS 4 Within 30 seconds, press the CABLE/DBS button. 3 Press the MUTE button. Your TV/VCR remote control may operate your Cable Box/DBS. If the remote control doesn’t operate your Cable Box/DBS now, follow the steps below to program your remote control.
• Although the remote control that comes with your TV/VCR will work most Cable Boxes and DBSs, it is possible that the remote control will not operate your Cable Box or DBS. • The remote control may only oper- ate some features of your Cable Box or DBS.
22 Front Panel STOP/EJECT REW PLAY F.FWD REC/OTR CHANNEL VOLUME POWER MTS MULTI TV STEREO head Cassette Compartment Insert a video cassette tape here. POWER Button Press to turn the power on or off. When you press the POWER button to turn on the TV/VCR, the remote locator will be activat- ed.
Rear Panel 23 ANT. L R AUDIO IN VIDEO IN ANT(enna) Jack Connect your antenna or cable here. Details are on pages six - seven. Antenna Hole Connect the stem of an indoor antenna here. Details are on page six. AC Power Cord Connect to a standard AC outlet to supply power to the TV/VCR.
24 Remote Control Buttons CH(annel). Up/Down Buttons Press to scan through the channels of the TV/VCR or the Cable Box/DBS. A.CH (Alternate Channel) Button Press to return to the TV channel you were viewing immediately before switching to your current channel.
VAR.SLOW CABLE/DBS COMBI VOL. CH. A.CH +100 3 6 9 0 2 5 8 1 4 7 TRACKING F.ADV SLEEP REC/OTR POWER SPEED STATUS/EXIT STOP PLAY F.FWD REW MEMORY SLOW MUTE VCR PLUS+ /ENTER SMART PICTURE SKIP SEARCH SMA.
VAR.SLOW CABLE/DBS COMBI VOL. CH. A.CH +100 3 6 9 0 2 5 8 1 4 7 TRACKING F.ADV SLEEP REC/OTR POWER SPEED STATUS/EXIT STOP PLAY F.FWD REW MEMORY SLOW MUTE VCR PLUS+ /ENTER SMART PICTURE SKIP SEARCH SMA.
Smart Picture 27 The Smart Picture feature allows you to improve the TV/VCR’s picture when viewing sports, a movie, or video games; to improve the picture when the antenna/cable signal is weak; or to reset the picture controls to their original settings.
28 Remote Locator Your TV/VCR can find your remote control for you. When you press the POWER button on the TV/VCR to turn on the TV/VCR, your remote control beeps and LOCATING REMOTE appears on-screen. The remote control will beep for about 30 seconds.
• If the channel you select has no broadcast, the screen will be solid blue. • You cannot view closed captions during recording or tape playback if COUNTER ONLY is set to ON. Details are on pages 45 - 46. Helpful Hints 1 Press the COMBI button, then press the MENU button.
30 Reminder The channel number will remain on-screen at all times when you set REMINDER to ON in the pop up menu. The exception is dur- ing tape playback, Forward and Reverse Searching and Still modes, and when closed captioning is selected (CAPTION in the pop up menu).
Playing 31 • If the tape you want to play is already in the TV/VCR, turn on the TV/VCR power, then press the COMBI button, then press the PLAY/ ▲ button. • Playback features and options are on pages 48 - 54. Helpful Hints Follow the steps below to play a tape.
32 Recording • You cannot record one channel while watching another. • Recording options are on pages 33 - 43. • You cannot record if DEFEAT RECORDING is set to ON.
One-Touch Recording 33 The One-Touch Recording (OTR) function allows you to program an immediate timed recording from 30 minutes to eight hours long without setting the timer. Before you begin, make sure: ● Channels are set up. ● There is a tape in the TV/VCR.
34 Rerecording (Tape Duplication) • Unauthorized recording of copy- righted television programs, video tapes, or other materials may infringe on the rights of copyright owners and violate copyright laws. • Different brands of equipment may operate differently.
Timer Recording 35 Follow the steps below to program the TV/VCR to record TV programs while you’re away from home. The TV/VCR will turn itself on, record, and turn itself off automatically. Before you begin, make sure: ● The clock is set. If not, CLOCK MUST BE SET appears.
ONE TIME PROGRAM PROGRAM 1 CHANNEL – – TO CORRECT PRESS CLEAR TO END PRESS EXIT 36 Timer Recording (cont’d) 5 ● Enter the channel of the TV program you want to record (you must enter a 0 before all single-digit channels). ● If you are recording from line input, press 0, 0.
Timer Recording (cont’d) 37 The TV/VCR must be off for a timer record- ing! Make sure there i s a tape in the TV/VCR. 8 Press the Number 1 button to record in SP speed, press the Number 2 button to record in LP speed, or press the Number 3 button to record in SLP speed.
38 Timer Recording (cont’d) 6 Repeat steps 1 - 4 to make sure you have cleared the correct position. Checking or Clearing Timer Recordings 1 With the TV/VCR on, press the COMBI button, then press the MENU button. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select VCR PROGRAM, then press the F.
Setting Up the VCR Plus+ Programming System 39 1 First, fill in the boxes on this page. It will only take a few minutes, and you must do it if you want the VCR Plus+ programming system to work properly.
40 Setting Up the VCR Plus+ Programming System (cont’d) 2 Now, compare the channel numbers you have written in the VCR PLUS+ CH. and CABLE/TV CH. columns. You’ll notice that some stations have VCR Plus+ and Cable/TV channel numbers that are the same, and other stations have channel numbers that do not match.
1 Press the COMBI button, then press the VCR PLUS+/ENTER button. VCR PLUS+ PROGRAM PLUS CODE : – – – – – – – – TO END PRESS EXIT Timer Recording With the VCR Plus+ Programming System 41 Follow the steps below to program a timer recording using the PlusCode programming numbers in your TV guide.
42 Timer Recording With the VCR Plus+ Programming System (cont’d) • To exit the VCR Plus+ programming system at any time, press the STA- TUS/EXIT button. The display will disappear from the screen. • To stop a started timer recording, press the STOP/EJECT button on the TV/VCR.
Defeat Recording 43 Follow the steps below to prevent accidental recording. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select VCR SETUP, then press the F.FWD/ B button. 3 Press the PLAY/ ▲ button or the STOP/ ▼ button to select DEFEAT RECORDING, then press the F.
44 Setting the Sleep Timer Use the sleep timer to program the TV/VCR to shut off in a cer- tain amount of time. 1 Press the COMBI button, then press the SLEEP button. The sleep timer display will appear on-screen. (You can not set the sleep timer during a recording.
When you watch a program that is being broadcast with closed captions, you can access on-screen boxes containing the pro- gram’s dialogue (for example, what a character is saying), dialogue in a foreign language, or information (such as a channel guide, schedule, or announcements).
46 Closed Caption (cont’d) • You cannot view closed captions during recording or tape playback if COUNTER ONLY is set to ON. • Abbreviations, symbols, and other grammatical shortcuts are often used in order to keep pace with the on-screen action.
VAR.SLOW CABLE/DBS COMBI VOL. CH. A.CH +100 3 6 9 0 2 5 8 1 4 7 TRACKING F.ADV SLEEP REC/OTR POWER SPEED STATUS/EXIT STOP PLAY F.FWD REW MEMORY SLOW MUTE VCR PLUS+ /ENTER SMART PICTURE SKIP SEARCH SMART SOUND INDEX SEARCH EJECT MENU CLEAR PAUSE/STILL Usually, the volume bar appears when you press the VOL(ume).
48 Repeat Play Follow the steps below to program the TV/VCR to play a tape over and over. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select VCR SETUP, then press the F.FWD/ B button. 3 Press the PLAY/ ▲ button or the STOP/ ▼ button to select REPEAT PLAY, then press the F.
A - B Repeat Play 49 • To cancel A-B Repeat Play, set ONE TIME PLAY to ON. To set ONE TIME PLAY to ON, follow steps 1 - 3 above. Then, press the PLAY/ o button or the STOP/ p button to select ONE TIME PLAY. Press the F.FWD/ B button so that ON appears beside ONE TIME PLAY.
6 Press the STATUS/EXIT button to remove the display. A- B REPEAT will appear on-screen. Beneath it, the letter A will flash beside the real-time counter. . A-B REPEAT A 1:23:45 7 Play, fast forward, or rewind the tape to the position at which you want to begin playback.
Real-Time Counter Memory 51 Follow the steps below to reset the real-time counter to zero at a tape location you want to refer to later. 1 Play, fast forward, or rewind a tape to the location that you would like to refer to later. Stop the tape. 2 Press the STATUS/EXIT button.
52 Index Search This feature allows you to index the starting points of programs that you have recorded on a tape. Then, you can easily rewind or fast forward to that point. Example: If you are watching program number 4 and you want to fast for- ward to program number 7, skip three programs.
Automatic Operation Features 53 The following playback features will always operate. Automatic Playback When you put a tape in the TV/VCR, the power will come on automatically.
54 Playback Options Forward and Reverse Searching (SP/LP/SLP) 1 During tape playback, press and release the F.FWD/ B button or the REW(ind)/ { button. A fast forward or reverse picture search will begin. 2 To return to normal playback, press the PLAY/ ▲ button.
MTS Broadcast Stereo System 55 Your TV/VCR can receive a program broadcast in stereo or with second audio (usually, that means a pro- gram is broadcast with a second language). When the second audio is available, you can select either the main audio (Mono) or the second audio.
56 MTS Broadcast Stereo System (cont’d) 4 Press the STATUS/EXIT button . 1 Press the COMBI button, then press the MENU button. 2 Press the PLAY/ ▲ button or the STOP/ ▼ button to select STEREO/SAP. 3 Press the REW(ind)/ s button or the F.FWD/ B button to select STEREO, SAP, or MONO.
Specifications General CRT: 19-inch in line gun Television system: NTSC-M Closed caption system: Section 15.119, FCC (Federal Communications Commission) Standard Video Heads: Four heads Tape width: 1/2 inch (12.65 mm) Tape speed SP: 33.35 mm/sec. LP: 16.
58 Helpful Hints Location For safe operation and satisfactory performance of your TV/VCR, remember the following: • Shield it from direct sunlight and keep it away from sources of intense heat. • Avoid dusty or humid places. • Avoid places with insufficient ventilation.
Helpful Hints (cont’d) 59 The remote control is not available, or the remote control will not access the pop up menu. • Use the buttons on the front panel of the TV/VCR to access the pop up menu (page 22). You can not enter numbers (for example, to program a timer recording) using the front panel buttons.
60 Limited Warranty WHO IS COVERED? You must have proof of purchase to receive warranty service. A sales receipt or other document showing that you purchased the product is considered proof of purchase. WHAT IS COVERED? Warranty coverage begins the day you buy your product.
a-b repeat play . . . . . . . .49 - 50 accessories . . . . . . . . . . . . . . .64 ant(enna) jack . . . . . . . . . . .6, 23 audio in jacks . . . . . . . .7, 23, 34 automatic playback . . . . . . . . . . . . . . .53 rewind . . . . . . . . . . . . . . .
CCZ196comb.QX33 4/6/99 7:05 PM Page 62.
CCZ196comb.QX33 4/6/99 7:05 PM Page 63.
IB8046E001 Printed In Mexico 0EMN01367 / B7962UN * * * * * S UPPLIED A CCESSORIES Remote Control (4835 218 37227) Three AA Batteries (4835 138 17012) Check to be sure the items on this page are packed with your TV/VCR. These accessories are provided to help you use or set up your TV/VCR.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Magnavox CCZ196AT è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Magnavox CCZ196AT - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Magnavox CCZ196AT imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Magnavox CCZ196AT ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Magnavox CCZ196AT, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Magnavox CCZ196AT.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Magnavox CCZ196AT. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Magnavox CCZ196AT insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
