Manuale d’uso / di manutenzione del prodotto BEFN2PS4 del fabbricante Linksys
Vai alla pagina of 31
Instant Br oadband™ Series EtherFast ® Cable/DSL & Voice Router powered by Net2Phone Use this Guide to install: BEFN2PS4 User Guide.
COPYRIGHT & TRADEMARKS Copyright © 2000 Linksys, All Rights Reserved. Instant Broadband is a r egistered trademark of Linksys. Microsoft, Windows, and the Windows logo ar e register ed trade- marks of Microsoft Corporation.
Instant Broadband TM Series EtherFast ® Cable/DSL & Voice Router powered by Net2Phone T able of Contents Introduction 1 About Net2Phone 1 F eatures 2 Package Contents / System Requirements 3 Gett.
Package Contents • One Linksys Instant Broadband EtherF ast ® Cable/DSL & V oice Router po wered b y Net2Phone • One po wer adapter • One Net2Phone Access Card (Not Sho wn) • One T echHel.
Uplink The Uplink P or t is where y ou can expand y our net- w ork by connecting to another s witch or hub . The Uplink P or t is shared with P ort 4. Uplinking to another Router , switch or a hub is done b y simply running a cable from the Uplink P or t to the other device.
The W AN Indicators Link Gr een . The Link LED illuminates when a successful con- nection is made betw een the Router and your Broadband device or netw ork. Act Gr een . The Act LED flickers when the Router is sending or receiving data o ver the broadband port.
EtherFast ® Cable/DSL & Voice Router powered b y Net2Phone 9 DHCP (Dynamic Host Configuration Protocol) DHCP is software that automati- cally assigns IP addresses to client stations lo gging onto a TCP/IP network. DHCP eliminates ha ving to manually assign permanent IP addresses to every device on y our netw ork.
No w that your Router is ph ysicall y installed , you will ha ve to conf igure your PCs to accept the IP addresses that your Router will pro vide. These instructions apply onl y to W indows 95 and W indo ws 98 machines. F or TCP/IP setup under W indo ws NT , please refer to your Microsoft W indo ws NT manual.
Configuring Y our Network with the Cable/DSL & Voice Router Configuring the Cable/DSL & V oice Router No w that your Cable/DSL & V oice Router is wired into your netw ork, you can begin conf iguring your system. 1. Open y our web br o wser and type http://192.
4. Conf igure the f ollo wing values . Host Name & Domain Name These f ields allow y ou to supply a host and domain name for the Router . Some ISPs require these names as identif i- cation. Y ou ma y hav e to check with your ISP to see if your Broadband Internet ser vice has been conf igured with a host and domain name.
6. Choose the DHCP tab . 7. Unless you alr eady ha v e a DHCP serv er on your internal network, choose Ena ble from the DHCP Server f ield. By choosing Enable, y ou will conf ig- ure the Router to automatically assign IP addresses to each of your PCs.
19 Setting Up Y our Net2Phone Account Once your Router is completel y installed and set up, you can acti v ate your Net2Phone account. Y ou will need the follo wing before you can set up your Linksys .
Setup The Basic Setup screen is the f irst screen you will see w hen you access the Utility . If you ha ve already installed and setup y our router , you ha ve already seen this screen and ha ve already properly conf igured all of the screen’ s val- ues.
EtherFast ® Cable/DSL & Voice Router powered b y Net2Phone 23 • Net2Phone Option This option enbles y our Net2Phone account that came with your Router .
EtherFast ® Cable/DSL & Voice Router powered b y Net2Phone DHCP A DHCP (Dynamic Host Conf iguration Protocol) Server automatically assigns IP addresses to each computer on your netw ork. Unless you already ha ve one, it is highly recommended that y our router be set up as a DHCP server .
EtherFast ® Cable/DSL & Voice Router powered b y Net2Phone 27 Help Here you will f ind links to all of the Utility’ s internal suppor t documentation, a link to Linksys’ s website, the application that upgrades the Router’ s f irmware, as w ell as a link to Net2Phone’ s w ebsite for Net2Phone account management.
EtherFast ® Cable/DSL & Voice Router powered b y Net2Phone Filters b lock specif ic inter nal users from accessing the Inter net. Y ou can set up a f ilter through an IP address or a netw ork Port number . T o Modify Filter Settings • Enter the IP addresses you wish to f ilter into the IP address f ields.
EtherFast ® Cable/DSL & Voice Router powered b y Net2Phone For P or t forwarding sets up pub lic services on your netw ork. When users from the Internet make cer tain requests of your netw ork, the router will forward those requests to the appropriate computer .
EtherFast ® Cable/DSL & Voice Router powered b y Net2Phone Static Routing If your Router is connected to more than one netw ork, it ma y be necessar y to set up a static route betw een them. A static route is a pre-determined pathwa y that netw ork infor mation must trav el to reach a specif ic host or network.
The DMZ Host setting allo ws one local computer to be exposed to the Internet to use a special-pur pose ser vice such as Inter net gaming or video- conferencing. T o expose one computer , enter the computer’ s IP address and click the Appl y button.
Troubleshooting Common Problems and Solutions This section pro vides possible solutions to problems re garding the installation and operation of the Cable/DSL V oice Router . Read below description to solve y our problems. If you can’ t f ind an answ er here, check the Linksys w ebsite at www .
should be the Router’ s IP Address, and DNS (in "More".) • Same as abo ve, check the same setup v alues in the Status Monitor page of the Cable/DSL Router . 4. When I enter a URL or IP address, I get a time out error . • Check if other PCs w ork.
ports 7777, 7778, 7779, 7780, 7781, and 27900 to the IP address of the ser v- er . If you w ant to use the UT Ser ver Admin, forward another port (8080 usually w orks well), then in the [UW eb.
Which modems are compatible with the router? The router is compatib le with virtually an y cable or DSL modem that supports Ethernet. What are the advanced features of the router? The router's adv anced features include Filters, F orwarding, Dynamic Routing, Static Routing, and DMZ host.
44 Instant Broadband TM Series What happens when I don't hear the dial-tone? There are chances that the W A V f iles ha ve been corr upted. Either upg rade the f irmware (see page 25) or , if you ha ve already upg raded , reapply y our f ir mware upgrade.
3. At the DOS command prompt , type "ping mail" (assuming that the location for which y ou’ re trying to f ind an IP address is conf igured as “mail”). Press Enter . Information such as the following data, tak en from a ping of Microsoft Netw ork’ s e-mail ser ver , will be displa yed.
48 Instant Broadband TM Series F ollo w these instructions to install the TCP/IP Protocol on one of your PCs only after a netw ork card has been successfully installed inside the PC. These instructions are for W indo ws 95 and W indows 98. F or TCP/IP setup under Microsoft W indows NT , please refer to your Microsoft Windo ws NT manual.
50 Instant Broadband TM Series There are different grades, or categories, of twisted-pair cab ling. Category 5 is the most reliable and is highl y recommended. Category 3 is a good second choice. Straight-through cables are used for connecting computers to a hub .
52 Instant Broadband TM Series EtherFast ® Cable/DSL & Voice Router powered by Net2Phone Warrant y Information BE SURE T O HA VE Y OUR PROOF OF PURCHASE AND A BARCODE FR OM THE PR ODUCT'S P A CKA GING ON HAND WHEN CALLING. RETURN REQUESTS CANNO T BE PR OCESSED WITHOUT PR OOF OF PURCHASE.
Contact Information F or help with the installation or operation of this product, contact Linksys Customer Support at one of the phone numbers or Inter net addresses below . Information 800-546-5797 (LINKSYS) T ech Support and RMA Issues 800-326-7114 Fa x 949-261-8868 Email support@linksys.
© Copyright 2000 Linksys, All Rights Reserved. Printed in the USA. http://www .linksys.com.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Linksys BEFN2PS4 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Linksys BEFN2PS4 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Linksys BEFN2PS4 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Linksys BEFN2PS4 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Linksys BEFN2PS4, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Linksys BEFN2PS4.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Linksys BEFN2PS4. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Linksys BEFN2PS4 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
