Manuale d’uso / di manutenzione del prodotto IDEALARC SP-255 del fabbricante Lincoln Electric
Vai alla pagina of 53
IDEALARC SP-255 OPERA TOR’S MANUAL IM533 June, 1998 Safety Depends on You Lincoln arc welding and cutting equipment is designed and built with safety in mind. However, your overall safety can be increased by proper installation ... and thought- ful operation on your part.
FOR ENGINE powered equipment. 1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running. ____________________________________________________ 1.b. Operate engines in open, well-ventilated areas or vent the engine exhaust fumes outdoors.
ii SAFETY ii ARC RA YS can burn. 4.a. Use a shield with the proper filter and cover plates to protect your eyes from sparks and the rays of the arc when welding or observing open arc welding. Headshield and filter lens should conform to ANSI Z87. I standards.
FOR ELECTRICALL Y powered equipment. 8.a. Turn off input power using the disconnect switch at the fuse box before working on the equipment. 8.b. Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturer’s recommendations.
iv SAFETY iv PRÉCA UTIONS DE SÛRETÉ Pour votre propre protection lire et observer toutes les instructions et les précautions de sûreté specifiques qui parraissent dans ce manuel aussi bien que les précautions de sûreté générales suiv- antes: Sûreté Pour Soudage A L’Arc 1.
Thank You for selecting a QUALITY product by Lincoln Electric. We want you to take pride in operating this Lincoln Electric Company product ••• as much pride as we have in bringing this product to you! Read this Operators Manual completely before attempting to use this equipment.
vi APR96 IDEALARC SP-255 MASTER T ABLE OF CONTENTS FOR ALL SECTIONS Page Installation .......................................................................................................Section A Technical Specifications ...........................
vii IDEALARC SP-255 MASTER T ABLE OF CONTENTS FOR ALL SECTIONS Page Maintenance ....................................................................................................Section D Safety Precautions ..........................................
A-1 INST ALLA TION AUG 95 IDEALARC SP-255 75C Copper Wire 75C Copper Wire in Conduit in Conduit Input Fuse or Input Ampere AWG (IEC) AWG (IEC) Voltage/ Breaker Size Rating on Sizes Sizes Frequency (Super Lag) Nameplate For lengths For lengths Ground Wire up to 100 ft.
A-2 INST ALLA TION IDEALARC SP-255 OCT94 Read entire Installation section before starting installation. SAFETY PRECA UTIONS UNCRA TING THE SP-255 Remove the staples from the bottom edge of the car- ton and lift off. Cut the tape securing the two rear wheels to the wooden shipping pallet.
The 230/460/575 volt 60 Hz model is not equipped with a plug, input cable or receptacle. 4. Using the following instructions have a qualified electrician connect the receptacle or cable to the input power lines and the system ground per the U.S. National Electrical Code and any applicable local codes.
A-4 INST ALLA TION IDEALARC SP-255 OCT94 However, the thumbswitch functions available on the Magnum 250SP gun will only be operable from the front panel keypad. The gun trigger switch must be capable of switching 5 milliamps at 15 volts DC– resistive.
IDEALARC SP-255 B-1 OPERA TION Read entire Operation section before operating the SP-255. ELECTRIC SHOCK can kill. • Do not touch electrically live parts or electrode with skin or wet clothing. Insulate yourself from work and ground. • Always wear dry insulating gloves.
IDEALARC SP-255 B-2 OPERA TION PR ODUCT DESCRIPTION The SP-255 is a complete semiautomatic constant voltage DC arc welding machine built to meet NEMA specifications. It combines a constant voltage power source and a constant speed wire feeder with a micro- computer-based controller.
B-3 OPERA TION JAN96 IDEALARC SP-255 are held closed. The left pair will automatically contin- ue to increment or decrement the selection above it at a slow, steady rate as long as the key is pressed.
B-4 OPERA TION IDEALARC SP-255 Center arrow keys—set Wire Diameter Right arrow keys—set Welding Gas The following 16 processes are programmed into the SP-255: PROCEDURE KEYS AUTO KEY Pressing the Auto Key once places the SP-255 into the automatic mode of operation.
B-5 OPERA TION IDEALARC SP-255 Repressing the Auto Key sets the recommended pro- cedure for the metal thickness displayed. MANUAL KEY Permits individual setting of wire feed speed and arc voltage for manual procedure setup.
B-6 OPERA TION IDEALARC SP-255 OCT94 The six arrow keys perform no function during a recall. NOTE: The presently displayed setup is lost because it is replaced by the setup recalled from memory. If you wish to save the present setup, save it to an unused memory first (see Save key), and then recall the memory required.
B-7 OPERA TION IDEALARC SP-255 STITCH KEY Turns on the Stitch weld timers and displays selec- tions of the stitch ON and OFF times. Pressing the Stitch key a second time returns the screen to the previous display without turning off the stitch timers.
B-8 OPERA TION IDEALARC SP-255 The first time this key is pressed it turns on toggle mode and recalls the setup in memory 4. This mode allows you to toggle between the setups in memory 4 and memory 5. Each time the key is pressed, it alter- nates between the two memories.
B-9 OPERA TION IDEALARC SP-255 the one that did not match (see Memory Number Key Section). 4-STEP TRIGGER INTERLOCK KEYS Pressing and Controls whether 4-step trigger interlock is activated or deactivated. (See “Using 4-Step Trigger Interlock Function” section.
B-10 OPERA TION IDEALARC SP-255 GUN SWITCHES Gun Trigger Switch — Turns on arc voltage, wire feeder, and gas solenoid (except with Innershield) when closed. Also causes the screen to display the Auto or Manual screens (depending on which mode it is in), when the trigger is pulled.
B-11 OPERA TION IDEALARC SP-255 Check to be sure the retaining spring has fully returned to the locking position and has securely locked the Readi-Reel cage in place.
B-12 OPERA TION IDEALARC SP-255 OCT94 3. If the only result was drive roll slippage, loosen the gun cable Fast-Mate™ connection nut from the front of the SP-255 and pull the gun cable forward about 6” (152 mm). There should be a slight wavi- ness in the exposed wire.
B-13 OPERA TION IDEALARC SP-255 12. When no more welding is to be done, close valve on gas cylinder (if used), momentarily operate gun trigger to release gas pressure, and turn off SP-255.
EXPLANA TION OF PROMPTING AND ERR OR MESSA GES On Screen Error Message Message Explanation PROCESS MUST MATCH WIRE & GAS ONLY SET UP FOR .035 STAINLESS ONLY ARGON USED WITH ALUMINUM ONLY SET UP FOR .
REQ’S: STAINLESS WIRE .035 Ar0 2 PRESS PROCESS WHEN INSTALLED DATA ***ERROR*** CHECK SETTINGS PRESS PROCESS TO CHECK SETTINGS MOTOR OVERLOADED CHECK GUN, DRIVE XXXX ***ERROR*** CHECK SETTINGS PRESS PROCESS TO CHECK SETTINGS GUN SWITCH BEING USED FOR TOGGLE CONNECT FOR NEG.
B-16 IDEALARC SP-255 OCT94 OPERA TION On Screen Error Message Message Explanation HIGH LINE: CHECK RECONNECT PANEL PRESS ANY KEY TO STOP MESSAGE CURRENT OVERLOAD REDUCE OUTPUT PRESS ANY KEY TO STOP ME.
for use of the K487 Spool Gun (with remote speed control), or the K469 Spool Gun (requires K518 Connection Adapter). It also provides single switch transfer of Trigger and Wire Speed Controls between the 250SP gun or the spool gun for same polarity welding with different wire and gas processes.
C-2 A CCESSORIES IDEALARC SP-255 OCT94 d. Procedure settings may be stored in memory for later recall. (See “Memory Keys” in Operation section.) 4.
C-3 A CCESSORIES IDEALARC SP-255 memory 4 is recalled and appears on the display. This whole cycle is repeatable as long as the unit remains in Toggle mode.
C-4 NO TES IDEALARC SP-255.
D-1 MAINTENANCE IDEALARC SP-255 GUN TUBES AND NOZZLES 1. Replace worn contact tips as required. 2. Remove spatter from inside of gas noz- zle and from tip after each 10 minutes of arc time or as required. CABLE CLEANING Clean cable liner after using approximately 300 pounds (136 kg) of electrode.
D-2 MAINTENANCE IDEALARC SP-255 out straight on a flat surface. Remove the liner nut from the Fast-Mate™ connector end of the cable and pull the liner out of the cable. 4 . Insert a new untrimmed liner into the connector end of the cable. Be sure the liner busing is stencilled appropriately for the wire size being used.
D-3 MAINTENANCE IDEALARC SP-255 GUN HANDLE DISASSEMBL Y The internal parts of the gun handle may be inspected or serviced if necessary. The gun handle consists of two halves that are held together with a collar on each end.
D-4 NO TES IDEALARC SP-255.
E-1 TR OUBLESHOO TING IDEALARC SP-255 Step 1. LOCATE PROBLEM (SYMPTOM). Look under the column labeled “PROBLEM (SYMPTOMS)”. This column describes pos- sible symptoms that the machine may exhibit. Find the listing that best describes the symptom that your machine is exhibit- ing.
IDEALARC SP-255 E-2 TR OUBLESHOO TING Observe Safety Guidelines detailed in the beginning of this manual. TR OUBLESHOO TING GUIDE PROBLEMS (SYMPT OMS) Major physical or electrical damage is evident. There is no wire feed or open circuit voltage when the gun trigger is pulled.
IDEALARC SP-255 E-3 TR OUBLESHOO TING Observe Safety Guidelines detailed in the beginning of this manual. TR OUBLESHOO TING GUIDE If for any reason you do not understand the test procedures or are unable to Perform the tests/repairs safely, contact your LOCAL AUTHORIZED LINCOLN ELECTRIC FIELD SERVICE FACILITY for assistance before you proceed.
E-4 TR OUBLESHOO TING IDEALARC SP-255 PROBLEMS (SYMPT OMS) The welding arc is unstable or “hunting”. POSSIBLE AREAS OF MISADJUSTMENT(S) 1. Check the work cable for loose or faulty connections. 2. Check the contact tip and replace if worn or damaged.
E-5 TR OUBLESHOO TING IDEALARC SP-255 Observe Safety Guidelines detailed in the beginning of this manual. TR OUBLESHOO TING GUIDE PROBLEMS (SYMPT OMS) The SP-255 stops feeding wire while welding and the MOTOR OVERLOADED message appears on the LCD display.
IDEALARC SP-255 E-6 TR OUBLESHOO TING Observe Safety Guidelines detailed in the beginning of this manual. TR OUBLESHOO TING GUIDE If for any reason you do not understand the test procedures or are unable to Perform the tests/repairs safely, contact your LOCAL AUTHORIZED LINCOLN ELECTRIC FIELD SERVICE FACILITY for assistance before you proceed.
F-1 WIRING DIA GRAMS IDEALARC SP-255 SP-255 WIRING DIA GRAM: L9688 (DU AL V OL T A GE) NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside the machine on one of the enclosure panels.
F-2 WIRING DIA GRAMS IDEALARC SP-255 SP-255 WIRING DIA GRAM: L9689 (230/460/575V) NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside the machine on one of the enclosure panels.
F-3 DIMENSION PRINT IDEALARC SP-255 SP-255 DIMENSION PRINT – M16352 (1-31-92B) Inches (Millimeters).
NO TES.
NO TES.
NO TES.
NO TES.
Now A vailable...12th Edition The Procedure Handbook of Ar c W elding With over 500,000 copies of previous editions published since 1933, the Procedure Handbook is considered by many to be the “Bible” of the arc welding industry. This printing will go fast so don’t delay.
W ARNING A VISO DE PRECA UCION A TTENTION W ARNUNG A TENÇÃO Spanish French German Portuguese Japanese Chinese Korean Arabic READ AND UNDERST AND THE MANUF ACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BE USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.
W ARNING A VISO DE PRECA UCION A TTENTION W ARNUNG A TENÇÃO Spanish French German Portuguese Japanese Chinese Korean Arabic LEIA E COMPREENDA AS INSTRUÇÕES DO F ABRICANTE P ARA ESTE EQUIP AMENTO E AS P ARTES DE USO, E SIGA AS PRÁTICAS DE SEGURANÇA DO EMPREGADOR.
• Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Lincoln Electric IDEALARC SP-255 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Lincoln Electric IDEALARC SP-255 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Lincoln Electric IDEALARC SP-255 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Lincoln Electric IDEALARC SP-255 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Lincoln Electric IDEALARC SP-255, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Lincoln Electric IDEALARC SP-255.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Lincoln Electric IDEALARC SP-255. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Lincoln Electric IDEALARC SP-255 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
