Manuale d’uso / di manutenzione del prodotto LS50 del fabbricante LG Electronics
Vai alla pagina of 35
Service Manual LG Electronics (LS40, LS50).
2 1010 Battery Pack 1. Push the battery latch in the direc tion shown be low; then slide the battery pack out of the s lot. Remov ing and replacing a part (FRU).
3 1020 Hard Disk Drive 1 M3.0 X L6.0 1SZZBA4085A 1 EA Specific ation FRU No. No. 1. Remove a scre w as indicat ed in the pict ure, then pull the HDD Assy out in the direction sh own belo w.
4 2 M2.0 X L8.0 1SZZBA4083A 1 EA Speci fication FRU No. No. 1030 Keyboard 1. Remove 2 scr ews. Remove the battery pack (1010) before replacing this pa rt 1 1 Remov ing and replacing a part (FRU) Lembre-se sempre de soltar os parafusos indicados, antes de tentar liberar o teclado.
5 2. To remove three hooks, insert a (-) type screwdriver into a hook located at the lower end of keyboard, and pull it up. Remov ing and replacing a part (FRU) Não aplique força excessiva, uma leve.
6 1 3. Disconnect the keyboard connector. Remov ing and replacing a part (FRU).
7 1. Pull up the retainer, and rem over the connector using a (-) type screwdriver. Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard (1030) 1040 Retainer Remov ing and replacing a part (FRU) Evite o uso de chaves metálicas nesta parte, por marcar facilmente use ferramenta plástica ou somente as mãos.
8 1 3 M2.0 X L8.8 1SZZBZ4020A 1 EA Specif ication FRU No. No. 1 1 1050 Fan A ssembly 1. After removing a screw and the c onnector, pull up and remove the fa n Assy using a (-) type screwdriver.
9 1050 Fan A ssembly 1. After removing a screw and the c onnector, pull up and remove the fa n Assy using a (-) type screwdriver. Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard (1030) Retainer (1040) 3 M2.0 X L8.
10 1 1060-1 Optical Disk Drive (14.1” Model) 1. Remove a screw, in sert a screwdr iver into the back s ide of OD D and push it out. Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard (1030) Retainer (1040) 1 M2.
11 1060-2 Optical Disk Drive (15” Model) 1. Remove a screw, in sert a screwdr iver into the hole lo cated at the rear of OD D and push it out. Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard (1030) Retainer (1040) 1 M2.
12 1070 Wireless L A N Card 1. Remove two wireless LAN ca rd connector, open card knob to take out the card. Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard.
13 1 1 1080 MDC Modem Card 1. Remove two screws and inser t a screwdr iver be low the modem. Pull it up to disasse mble. Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard (1030) Retainer (1040) 2 M2.0 X L3.5 1SZZBA4017B 1 Qty Screw FRU No.
14 1 1 1 1 1090 Display Module 1. Remove two screws. Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard (1030) Retainer (1040) Wir eless LAN Card (1070 ) 2 M2.5 X L8.0 1SZZBA4039B 1 Qty Screw FRU No. No. 2. Remove two hinge cover screws.
15 1 1 3. Using a (-) t ype screwdriver from the back of the LCD, pull up the hinge cover with y our finger. The more you move the LCD to the back, the easier the hinge cover w ill pull out. Remove another hinge cover located on the other side . 4. Remove two hinge screws.
16 5. Remove the LCD connector located at the upper end of MCD modem. You will see a t ag designed to make the work easier . Pull out the tag. 6. Remove the LCD cable .
17 7. Hold the LCD with your both hands, and pull it up to re move. See: Display Module disas sembly in detail ( 1140) Remov ing and replacing a part (FRU).
18 Qty Screw FRU No. No. 2 M2.0 X L3.0 1SZZBA4017A 3 9 M2.0 X L8 1SZZBA4083A 1 2 M2.0 X L15 1SZZBZ3010Z 2 1100 Key Deck 1. Remove 14 screws ( for 15” m odel) or 11 screws ( for 14.
19 Qty Screw FRU No. No. 2 M2.0 X L3.0 1SZZBA4017A 1 1 1 Qty Screw FRU No. No. 2 M2.0 X L3.0 1SZZBA4041A 1 3. Open ODD plate and remove two screws 2. Open the I/O port cover and remove two screws.
20 4. Remo ve the cable, ho ld the keyboard deck with your both hands and pu ll it out. Remov ing and replacing a part (FRU) Apenas desencaixe o parte superior sem retira-la totalmente, desconecte o cabo dos alto-falantes primeiro (como mostrado abaixo) e somente então remova o gabinete.
21 5. Remo ve the speaker cab le located at the front o f key deck tha t is pulled up. Remov ing and replacing a part (FRU).
22 3 M2.0 X L3.5 1SZZBA4017B 1 Qty Screw FRU No. No. 1 1 1 1110 Main Board 1. Remove two screws and di sassemble the O DD Plate Assy. Remove the following parts in order before replacing this part.
23 2. Remove the PCMCIA B/D. 3. Remove the RTC battery connector from M/B. Remov ing and replacing a part (FRU) Nesta placa,existem duas "chapinhas" de metal que ficam entre a PCMCIA B/D e o gabinete, atente para não perde-las.
24 5. Remove the LAN S/B connector. Remov ing and replacing a part (FRU).
25 6. Remove the p ower cabl e. Remov ing and replacing a part (FRU).
26 3 M2.0 X L5.0 1SZZBZ4014A 1 1 M2.0 X L3.5 1SZZBA4017B 2 Qty Screw FRU No. No. 1 2 1 1 7. Remove 4 M/B screws. Remov ing and replacing a part (FRU).
27 8. Hold M/B with your both hand and pull it up to remove. Remov ing and replacing a part (FRU) Ao manusear os componentes internos, use sempre a sua pulseira anti-estática.
28 2(14.1”) 3(15.0”) M2.0 X L3.5 1SZZBA4017B 1 Qty Screw FRU No. No. 14.1” 15” 1 1 1 1 1 1120 Battery Frame As sy 1. Remove a screw. Remove the following parts in order before replacing this part.
29 1130 S-Video Sub-Board 1. Remove the S-Video sub-board. Remove the following parts in order before replacing this part. Battery Pack (1010) Keyboard (1030) Retainer (1040) Fan Assembly (1050) Wir e.
30 1 1 1 1 2 1 2 5 M2.5 X L4.0 1SZZBA4044B 1 2 M2.5 X L5.0 1SZZBA4068A 2 Qty Screw FRU No. No. 1140 Display Module 1. Using a knife, r emove the logo and rubbers that are covering the screws. Then re move all 7 scr ews. Remove the following parts in order before replacing this part.
31 2. Disassemble the LCD front. The fr ont hook located on the middle of LCD upper and lower end. Be careful of the direction when removing because it is connected from inside out.
32 3. Remove cable connector. Remo ve the cable that is arr anged around LCD from the LCD frame . Remov ing and replacing a part (FRU).
33 1 1 4 M2.0 X L2.5 1SZZBZ3009B 1 4 M2.5 X L5.0 1SZZBA4068A 2 2 M2.0 X L4.5 1SZZBA4082A 3 Qty Screw FRU No. No. 1 1 2 2 2 2 3 3 4. Remove 9 screws (for 15” model) or 8 scre ws (for 14.
34 5. Press the hook on the both side of LCD with a (-) ty pe screwdriver and remove from th e LCD rear panel. Remov ing and replacing a part (FRU).
35 6. Remove LCD from t he LCD rear panel. Remov ing and replacing a part (FRU).
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il LG Electronics LS50 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del LG Electronics LS50 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso LG Electronics LS50 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul LG Electronics LS50 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il LG Electronics LS50, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del LG Electronics LS50.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il LG Electronics LS50. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo LG Electronics LS50 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
