Manuale d’uso / di manutenzione del prodotto Wireless Temperature Station WS-7013TWC del fabbricante La Crosse Technology
Vai alla pagina of 23
Quick Start for your WS-7013U Hint: Use good quality Alkaline Batteri es and avoid rechargeable batteries. 1. Have the indoor station and outdo or remote 3 to 5 ap art. 2. Batteri es shoul d be out of bot h uni t s fo r 1 0 m i nut es. 3. Place the batteries into the outdoor remot e first then into the indoor station.
1 7, 0 ( WS-7013U Wireless 433 MHz Temperature Station Instruction Manual.
2 TABLE OF CONTENTS Topic Page Inventory of Contents 1 Quick Setup 2 Detailed Setup Guide Battery Installation 3-4 Setting the Time 5 Selecting Units of Measurement 6 Features Minimum and Ma ximum Tem.
1 INVENTORY OF CONTENTS 1. The Indoor Temperature Station (Figure 1) 2. The Remote Control Sensor (TX2U) and mounting bracket. (Figure 2) 3. 3 each, 1/2” Philips screws. 4. One strip of double sided adhesive tape. 5. Instruction Manual and Warranty Card.
2 QUICK SETUP 1. Insert two AAA batteries into the Remote Control Sender. 2. Insert two AAA batteries into the Indoor Temperature Station. 3. Wait 5-6 minutes, or until the outdoor temperature is displayed in the OUTDOOR LCD of the Temperature Station.
3 DETAILED SETUP GUIDE I. BATTERY INSTALLATION A. REMOTE CONTROL SENDER 1. Remove the mounting bracket. 2. Remove battery cover 3. Observing the correct polarity , install 2 AAA batteries—make sure they do not spring free, or start-up problems may occur.
4 7, 0 ( 1. Remove the battery cover on the backside. To do this, pus h up and pull out. 2. Observing the correct polarity , install 2 AA batteries. 3. Replace battery cover. 4. Wait 5-6 minutes or until both indoor and outdoor temperatures are shown on the Indoor Temperature Station.
5 II. TIME A. SETTING THE TIME 1. Press and hold the SET button for 1 second. “12h” will appear in the TIME LCD. 2. Use the MIN/MAX button to select either 12h time (am/pm) or 24h time 3. Press the SET button 2 times, the hour will flash in the upper left corner.
6 III. UNITS OF TEMPERATURE MEASURE A. SELECTING UNITS OF MEASUREM ENT 1. Press and hold the SET button for 1 second. 2. Press the SET button again. “ ° F” will appear in the TIME LCD. 3. Press the MIN/MAX button to shift between ° F and ° C. 4.
7 time of occurrence of the value for outdoor temperature will also flash. B. RESETTING THE MINIMUM AND MAXIMUM TEMPERA TUR ES 1. To reset both the minimum and maximum te mpe rature s—pre ss and hold the RESET/+ button for 4 seconds. C. ADDING ADDITIONAL REMOTE CONTROL SENDERS (OPTIONAL) 1.
8 display the temperature on its LCD, and the TX3UP will monitor the temperature via a probe for use in pools, spas, etc. 2. Note: When setting up multiple units it is importa n t to remove the batteries from all existing units in operation, then to insert batte rie s first into all the Remote Control Sender units , and in n umer ic sequen ce.
9 procedures seen in section I. A) of the Detailed Set-Up Guide). 7. Install batteries into the Indoor Temperature Station. 8. Follow the Detailed Set-Up Guide for programming and operating instructions. D. VIEWING AND OPERATING WITH MULTIPLE REMOTE CONTROL SENDER UNITS 1.
10 minimum an d ma xi mum out door temperature. 3. To rese t the Minimum/ Ma xi mum readings press and the MIN/MAX button for four seconds. V. MOUNTING A. Note: To achieve a true temperature reading, avoid mounting in direct sunlight. We recommend that y ou mount the Sender on an outside North-facing wall.
11 1. The Indoor Temperature Station comes with the table s tand already mounted. If y ou wish to use the table- stand, all that is required is to place the Indoor Temperature Station in an appropriate location. 2. To wall mount, remo ve the table stand.
12 TROUBLESHOOTING NOTE: For problems not solved, please contact La Crosse Technology via e-mail or phone, or visit our website, www.lacrossetechnology.com Problem: The LCD is faint Solution: 1) Replace batteries Problem: No outdoor temperature is display e d.
13 Solution: Each temperature sens or is manufactured to be accurate to within 1 degree plus or minus and under normal conditions; so two sensors could be as much as 2 degrees different. However, the difference can be exaggerated further because the sensors are designed for different working environments.
14 MAINTENANCE AND CARE INSTRUCTIONS • Extreme temp eratures, vibration, and shock should be avoided to prevent damage to the units. • Clean display s and units with a soft, damp cloth. Do not use solvents or scouring agents; they may mark the displays and casings.
15 SPECIFICATIO NS Transmitting Frequency 433MHz Measuring Temp eratures Temperature Station: Indoor 32 ° F to 156.2 ° F with 0.2 ° F resolution. (0 ° C to 69.0 ° C with 0.1 ° C resolution). Temperature Station: Outdoor -21.8 ° F to 156.2 ° F with 0.
16 Dimensions: (L x W x H) Temperature Station 2.75 x .92 x 4.3 in. (excluding table stand) (90 x 23.6 x 110 mm). Remote Control Sender 2.32 x 0.86 x 2.
17 herein, with new or recondit ioned parts or products if found to be defective dur ing the limited warranty period specified above. All replaced parts and products become the property of La Crosse Technology, Ltd and must be returned to La Crosse Technology, Ltd.
18 alterations by someone ot her than an authorized La Crosse Technology, Ltd aut horized serv ice center; (6) units used for other than home use (7) applications and uses that this product w as not intended or (8) the products inability to receiv e a signal due to any source of interference.
19 For warranty work, technic al support, or information contact: La Crosse Technology 2809 Losey Blv d. S. La Crosse, WI 54601 Phone: 608.782.1610 Fax: 608.796.1020 e-mail: support@lacrossetechnology.com (warranty work) sales@lacrossetechnology.com (information on other products) web: www.
20 FCC DISCLAIMER This device com p lies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device m ay not cause harm ful interference, and (2) this device m ust accept any interference received, including interference that m ay cause undesired operation.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il La Crosse Technology Wireless Temperature Station WS-7013TWC è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del La Crosse Technology Wireless Temperature Station WS-7013TWC - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso La Crosse Technology Wireless Temperature Station WS-7013TWC imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul La Crosse Technology Wireless Temperature Station WS-7013TWC ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il La Crosse Technology Wireless Temperature Station WS-7013TWC, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del La Crosse Technology Wireless Temperature Station WS-7013TWC.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il La Crosse Technology Wireless Temperature Station WS-7013TWC. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo La Crosse Technology Wireless Temperature Station WS-7013TWC insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
