Manuale d’uso / di manutenzione del prodotto EcoLAN 3000E del fabbricante Kyocera
Vai alla pagina of 20
Network Connectivity for Kyocera Printers Kyocera EcoLAN 3000E Quick Configuration Guide.
FCC Notice: This equipment complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Content s Introduction ......................................................................... 4 Using the CD ROM ............................................................. 4 Supported Kyocera Printer Models ................................... 5 EcoLAN 3000E Hardware Inst allation .
Introduction The EcoLAN 3000E is the next generation Kyocera internal network interface card allowing easy installation without removing the printer mainboard.
Supported Kyocera Printer Models The EcoLAN 3000E is compatible with the FS/LS-600, 680, 800, 1700+, 3700+, 5800C, 6700, 7000+, 9000 and any other Kyocera printer with the slide-in interface. The 3000E is compatible with the upper (hard disk) interface slot of an FS/LS-7000 with a Software version of 25.
6 NetW are 2.x & 3.x Configuration 1. Login as Supervisor and start PCONSOLE. 2. Define the Print Queue. ê If a Print Queue already exists that will be assigned to the 3000E, skip to step 3 ê Select Print Queue Information from the Available Options menu.
7 NetW are 4.x & 5.x Directory Services Configuration NetW are Directory Services (NDS) configuration is accomplished using two utilities; 1) NetW ares NW Admin is used to define the required D.
8 NetW are Directory Services Configuration continued... 3000E IPX Based Configuration IPX configuration is accomplished using the Management Access Program (MAP). 1. Install and Run MAP . ê Insert the CD included with the EcoLAN 3000E. ê In Windows 95, 98 or NT 4.
9 2. NetWare Configuration. ê Select Setup NetWare in the Protocols column. ê Enter the Print Server Name , Preferred NDS Context , and Print Server Password (if a password was defined) exactly as they were entered in NW Admin. Note: Entries are not case sensitive (except the sysadm pass- word).
10 Macintosh Configuration KPDL, Kyoceras PostScript compatible mode is required for Macintosh printing. KPDL is standard on many Kyocera printers, however , it is optional on the following models: FS-600, FS-680, FS-7000 and all LS (Japanese) models.
11 Inst alling the Driver and Selecting the Printer 1. The Macintosh LaserWriter Driver is installed from the CD provided with the printer . Insert the CD, open the Drivers folder , then the appropriate country folder , and double click on the FS-Series Installer program in the desired language.
12 Windows Peer to Peer Printing Configuration Peer to Peer printing is available for Windows 95, Windows 98 and Windows NT 4.0. What is Windows Peer to Peer Printing? The peer to peer printing software which is included with the EcoLAN 3000E allows Windows PCs to communicate directly with network attached printers.
13 IPX Printer Name: The IPX peer to peer printing software uses the NetW are Print Server Name to identify the 3000E. The default name is the serial number preceded by KYO, e.g., KYO_163495. If desired, this name can be changed to a more easily identifiable name with MAP .
Windows NT 4.0 Configuration There are several options for setting up printing in a Windows NT environment. u If a NetWare server is present, NetWare print services may be used by following the NetWare configuration instructions in this guide.
15 Configuring the Printer Driver for LPR Printing The printer driver should be installed from the CD which is shipped with the printer . Unfortunately , Windows does not make the Add LPR Port available to the Install Wizard on the CD. Therefore, the printer driver should be installed selecting a standard port such as LPT1.
16 DHCP Configuration (Dynamic Host Configuration Protocol) IMPORTANT: EcoLAN 3000E IP address assignment with DHCP will not work if the 3000E has an existing IP address and IP persistence is Permanent. DHCP provides a mechanism for delivering IP configuration parameters, including IP address, subnet mask, etc.
17 WINS Configuration (Windows Internet Naming Service) WINS provides a mechanism for mapping NetBIOS (Windows) names to IP ad- dresses. WINS enables defining a printing configuration which references the printer by its name rather than by its IP address.
18 UNIX Configuration UNIX printing utilizes a line printer daemon (lpd) to direct print jobs to the printer . The 3000E supports two modes of lpd printing, host-based lpd and printer-based lpd. With host-based lpd, the line printer daemon is run on one or more workstations (hosts) where print jobs are accepted and sent to the 3000E.
19 IP Address Setup with the Printer Front Panel Set the IP address and other 3000E parameters using the following procedure. Note: Setting the IP address with the front panel automatically sets IP Persistence to Permanent, that is, the IP address is maintained when the printer is turned off and on.
EcoLAN 3000E Quick Configuration Guide Re v . 1.0, June 1999 Part Number 8836056 Kyocera Corporation 2-14-9 T amagawadai, Set agaya W ard, T okyo 158 Japan Kyocera Communications Systems Co., Ltd. 2-14-9 T amagawadai, Set agaya W ard, T okyo 158 ww w .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Kyocera EcoLAN 3000E è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Kyocera EcoLAN 3000E - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Kyocera EcoLAN 3000E imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Kyocera EcoLAN 3000E ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Kyocera EcoLAN 3000E, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Kyocera EcoLAN 3000E.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Kyocera EcoLAN 3000E. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Kyocera EcoLAN 3000E insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
