Manuale d’uso / di manutenzione del prodotto KERS303BWH del fabbricante KitchenAid
Vai alla pagina of 16
INSTALLATION INSTR UCTIONS 30" (76 CM) FREESTANDING ELECTR IC RANGES T able of Conten ts RANGE SAFETY ................................ .................................. ................2 INSTALLATION RE QUIREMENTS ................ ..............
2 RANGE SAFETY You can be killed or seriously injured if you don't immediately You can be killed or seriously injured if you don't follow All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
3 INST ALLA TION REQUIREMENTS T ools and P ar ts Gather the req uired tools and part s befor e starting installation. Read and follow the instructions provided with any tools list ed here. T ools needed Parts supplied Check that all parts are included.
4 Product Dimensions IMPORT ANT : Range must be level after installation. Follow the instructions in the “Level Range” secti on. Using the cooktop as a refer ence for leveling the range is not recommended. * Range can be rai sed approximately 1" (2.
5 Electr ical Requirements - U .S.A. Only If codes permit and a separate ground wir e is used, it is recomm ended that a qualified elec trical installer determine that the ground path and wire gauge are in accordance with local codes. Do not use an extension cord.
6 INSTALLATION INSTR UCTIONS Unpack Range 1. Remove shipping materials, tape and film fr om range. 2. Remove oven racks and parts package from in side oven. 3. Do not remove the shipping base at this time. 4. On Ranges Equipped with a Storage Drawer: Remove the storage drawer .
7 Floor Mounti ng W all Mounting 5. Using the Phillips screwdriver , mount anti-tip bracket to the wall or floor with the two #12 x 1 ⁵⁄₈ " screws provided. 6. Move range close enough to opening to allow for final electrical connec tions. Remove shipping base, cardboar d or hardboar d from under range.
8 Electr ical Connection - U .S.A. Only 1. Disconnect power . 2. Remove the te rminal block cove r screws located on the bac k of the range. Pull cover down and towar d you to remove cover from range. 3. Remove plastic tag holding three 10-32 hex nuts from the middle post of the terminal block .
9 Style 2: Direct wir e strain relief ■ Remove the knockout as ne eded for the flexible conduit connection. ■ Assemble a UL listed conduit connector in the openi ng.
10 4. Use a Phillips screwdriver to connect the gr een ground wire from the power supply cord to the range with the ground-link screw and ground-link section. The ground wir e must be attached first. 5. Use ³⁄₈ " nut driver to connect the neutral (white) wire to the center terminal block post with one of the 10–32 hex nuts.
11 1. Part of metal ground strap must be cut out and r emoved. 2. Use a Phillips screwdriver to remove the gr ound-link screw from the back of the range. Save the ground-link scr ew and the end of the ground link under the screw . 3. Pull the wires thr ough the strain relief on bottom of range.
12 2. Attach terminal lugs to line 2 (red), bar e (green) gro und, and line 1 (black) wires. Loosen (do not remove) the setscrew on the front of the terminal lug and insert exposed wir e end through bottom of terminal lugs. Securely tighten setscrew to to rqu e as s ho wn i n t h e f o ll ow i ng B are Wi re T o rqu e Specifications chart.
13 6. Repeat steps 1 and 2 to ensur e that the range foot is engaged in the anti-t ip bracket. If the rear of the range lifts more than ½" (1.3 cm) off the floor without resistance, the a nti-tip bracket may not be installed correctly . Do not operate the range without anti-tip bracket installed and engaged.
14 Storage Draw er (on some models) The storage drawer can be removed. Before removing, make sure drawer is cool and empty . To R e m o v e : 1. Pull the storage drawer straig ht back to the drawer stop. 2. Lift up the fr ont of the dra wer and pull the drawer out.
15 Mo ving the Range When moving range, slide range onto cardb oard or hardboar d to avoid damaging the floor covering. If removing the range is necessary for cleaning or maintenanc e: For power supply cor d-connected ranges: 1. Slide range forward. 2.
W10403811C ® /™ ©2012 Whirlpool. All rights reser ved. 8/12 Printed in U.S.A..
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il KitchenAid KERS303BWH è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del KitchenAid KERS303BWH - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso KitchenAid KERS303BWH imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul KitchenAid KERS303BWH ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il KitchenAid KERS303BWH, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del KitchenAid KERS303BWH.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il KitchenAid KERS303BWH. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo KitchenAid KERS303BWH insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
