Manuale d’uso / di manutenzione del prodotto Rotary Mower del fabbricante King Kutter
Vai alla pagina of 46
ROTARY MOWER OPERATION AND PARTS MANUAL PO Box 1200 305 Commerce Drive Winfield, Alabama 35594 Part No 999998 www.kingkutter.com.
.
3 T O THE PURCHASER This manual cont ains valuable information about your new King Kutter Mower . It has been carefully prep ared to give you help ful suggestions for operating, adjusting, servicing and ordering rep air p art s. Keep this manual in a convenient place for quick and easy reference.
4 It is the purchaser and/or operator ’ s responsibility to…. z z z z z Read and underst and the information cont ained in this manual. z z z z z Operate, lubricate, assemble and maint ain the equip- ment in accordance with all instructions and safety pro- cedures in this manual.
5 CONTENTS ITEM P A G E Safety ......................................................................... 6 Assembly Instructions ................................................ 8 Before Putting Into Service ...................................... 1 1 Safety T raining .
6 SIGNAL WORDS: The signal words DANGER , W ARNING and CAUTION are used with the safety messages in this manual and with each safety signs. They are defined as follows: DANGER: Indicates an immediate hazardous situation that, if not avoided, could result in serious injury or death.
7 EQUIPMENT SAFETY GUIDELINES z Safety of the operator and by standards is one of the main concerns in designing and developing a mower . However , every year accidents occur which could have been avoided by a few seconds of thought and a more careful approach to handling equip- ment.
8 ROT AR Y MOWER ASSEMBL Y INSTRUCTIONS STEP 1 Place rotary mower on a flat, level surface. (See Figure A) STEP 2 Remove the wired on PTO shaft, lift pins, and spacers. Loosen and re- move the(4) bolts on the lift arm brackets, that secure the lift arm support straps, lift arms, and lift arm braces from the shipping positions and set aside.
9 STEP 7 Using the right side lift arm as a lever, pull to the outside of the lift arm bracket and inset bolt through lift arm and lift arm bracket. (See Figure I) In- stall washer and nut. Place the lift pin in the larger of the (2) holes on the lift arm brace and loosley attach the lift arm.
Figure E Figure F Figure G Figure H Figure I 10.
11 BEFORE PUTTING ROT AR Y MOWER INT O SER VICE ( IMPORT ANT -INSTRUCTIONS PRIOR T O ST ART UP) SHIPPED WITHOUT OIL IN GEAR BOX AND WITHOUT GREASE IN GREASE FITTINGS. UNIT MUST BE SERVICED BEFORE USING . • Fill Gearbox using Multi-Purpose Gear Oil (I.
SAFETY TRAINING z Safety is a primary concern in the design and manufacture of our product. Unfortunately , our effort s to provide safe equipment can be wiped out by a single careless act of an operator or bystander .
PREP ARTION z Never operate the tractor and mower until you have read and completely understand this manual, the T ractor Operator ’ s Manual, and each of the safety messages found on the safety signs on the tractor and mower .
14 OPERA TIONAL SAFETY z The use of this equipment is subject to certain hazards that cannot be pro- tected against by the mechanical means or product design. All operators of this equipment must read and understand this entire manual, paying particu- lar attention to safety and operating instructions, prior to using.
15 OPERA TIONAL SAFETY continued... z Never allow the cutting blade to contact such items. Cut material higher at first, allowing rotary mower to clear hidden objects.
OPERA TIONAL SAFETY continued... z Pass rotary mower diagonally through sharp dips and avoid sharp drops to prevent “hanging up” tractor and rotary mower . Practice will improve your skills in maneuvering on rough terrain. Always cut down slopes, never across the face.
A TT ACHING T O TRACT OR W ARNING Never stand between tractor and rotary mower while backing up tractor to the hitch. STEP 1 Attach to tractor's category 1, three point hitch as described in the T ractor's Operator ’ s Manual.
A TT ACHING T O TRACT OR continued.... STEP 5 Place and hold inner PTO shaft section next to outer section and check if PTO shaft is too long. Each section should end approximately 3 inches short of reaching u-joint shield on the opposite section.
19 STEP 1 Cutting the PTO shaft to length. NOTE: Be sure to cut equal lengths of each PTO shaft section. Clamp end of PTO shaft in a vice and cut off shield where marked. (Figure 1-A & 1-B) STEP 2 Using cut section of the shield as a guide cut shaft off the same amount.
OPERA TING INSTRUCTIONS This mower was designed to CUT P ASTURE GRASS AND ROUGH AREAS UP T O 1" IN DIAMETER.. Use of your rotary mower to cut any material larger than 1" in diameter may damage the mower and void your warranty .
Note: For best results in heavier cutting conditions adjust the deck so the rear of the mower is approximately 2" higher than the front. This method requires less horsepower and ground speeds of approximately 3-5mph. If finer shredding results are desired, adjust the deck to level or slightly lower in the rear .
MAINTENANCE 1) . Periodically check and maintain proper gear oil level. 2) . Every 8 hours, wheel fork(s), wheel hub(s), PTO shaft universal joints (2), and PTO telescoping surface. (See Figures M-1 & M-2) NOTE: Use only a grade T ype II tube grease.
MAINTENANCE SAFETY z Good maintenance is your responsibility . Poor maintenance is an invitation to trouble. z Follow good shop practices. z Keep service area clean and dry z Be sure electrical outlets and tools are properly grounded z Use adequate light for the job at hand.
24 SAFETY SIGN LOCA TIONS The types of safety signs and locations on the equipment are shown in the illustra- tion below . Good safety requires that you familiarize yourself with the various safety si.
25 1.
26 2 3.
4 5 27.
6 7 28 8.
29 **Must specify name brand of PTO. Ref. No. Part Name 147034 1 Roll Pin Kit 2 3 4 Male T ube End Y oke Implement End Y oke Female T ube End Y oke 500133 151065 151060 151070 3 2 1 4 5 7 6 9 T ractor.
30 Ref. No. Part Name 1 Cross Kit 2 3 4 Roll Pin Female T ube End Y oke Inner T ube Slip Clutch Assembly Male T ube End Y oke Outer T ube T ractor End Y oke Quick Disconnect Pin 5 6 7 8 9 Safety Shiel.
31 SLIP CLUTCH ASSEMBL Y Ref. No. Part Name 8" Clutch S pring with Compression Bolts & Nuts (Pkg 8) 1 7" Part Number Flanged Y oke 2 Sleeve 3 Clutch Plate 4 Friction Hub 5 Slip Clutch Lo.
32 * Depending on the size of rotary mower purchased, the blade carrier can be any of these 2 types. T ire & Rim /w Hub Ref. No. Part Name 1 2 3 4 Wheel Fork Assembly Wheel Hub Assembly A-Frame Assembly A-Frame Ht. Adj. Gear Box Slick Lift Arm Brace PTO Shaft w/ Slip Clutch Lift Arms 5 6 7 8 9 Part Number 10 11 12 CA T .
33 Ref. No. Part Name 1 T ire & Rim /w Hub 2 3 4 Wheel Fork Assembly Wheel Hub Assembly A-Frame Assembly A-Frame Ht. Adj. Gear Box Lift Arm Brace PTO Shaft Lift Arm Assembly 5 6 7 8 9 Part Number 10 11 12 CAT.
34 501000 403602 191200 403600 184080 310619 147134 403658 6'/80hp 403402 500002 195170 501000 403602 191200 403600 184065 310619 147134 403658 6'/60hp 403402 500002 195170 403041 403041 501002 501002 501230 501230 HEA VY DUTY LIFT 6' & 7' MOWER Ref.
Ref. No. Part Name 1 T ire & Rim /w Hub 2 3 Cross Axle Assembly Wheel Hub Assembly Gear Box PTO Shaft 5 6 403001 403564 191100 184060 147148 6'/60hp Part Number 403001 403564 191100 184005 14.
7' PULL MOWER Ref. No. Part Name 1 T ire & Rim /w Hub 2 3 4 Cross Axle Assembly Wheel Hub Assembly Rachet Jack Gear Box PTO Shaft Pull Arm (Fits Lef t or Right Side) Axle Cuff Swivel Yoke Assembly 5 6 7 8 9 Part Number 10 11 12 Blade Carrier Blade Bolt Set (Pkg.
37 BONDIOLI- (BYPY) 1 ). There are 3 white tabs around the cover as shown in (A in FIG . 1). T ake a screwdriver and press against the tabs one at a time with downward an- gular pressure toward the end of shaft marked (B in FIG . 2). As you are pressing tab grasp cover at point marked (B in FIG .
BONDIOLI COVER REMOV AL FIGURE- 1 FIGURE- 2 EUROCARDAN SERIES 4 COVER REMOV AL FIGURE- 3 FIGURE- 4 LA MAGDALENA COVER REMOV AL FIGURE- 5 38.
39 EUROCARDAN SERIES 5 1 ). There are 2 black tabs around the cover as shown in (B in FIG . 1). T ake a flat screwdriver and pry under the tabs one at a time at point (B in FIG . 2) lifting t ab over on top of (e-shaped lock). After both t abs are released you can slide the locking ring down the shaft in direction of (C in FIG .
40 HP GEARBOX 40.
41 Ref. No. Part Name Gearbox 184010 1 Snap Ring 2 3 5 7 9 11 12 13 14 15 16 17 19 10 8 4 6 Input Seal (NAK35X54X10) Front Cap Front Cap Gasket Snap Ring Snap Ring Bearing (Hoover 208) Input Gear Inpu.
60 HP GEARBOX 42.
43 Ref. No. Part Name Gearbox 184060 184065 1 Seal Input (NAK SC 35X60X10) 156040 2 3 5 7 9 11 12 13 14 15 16 17 18 19 20 129025 124133 155020 185015 129020 185035 155035 155040 186022 124134 156035 1.
1 2 3 4 5 6 7 8 9 10 11 10 7 6 12 13 14 15 14 16 17 18 19 20 80 HP GEARBOX 44.
Ref. No. Part Name Gearbox 184080 1 1/2" V ented Pipe Plug 2 3 5 7 9 11 12 13 14 15 16 17 18 19 20 10 8 4 6 Seal Input (NAK SC 35X60X10) 1/8" Pipe Plug Endcap Input Gasket Input Bearing Race.
1. Limited W arranty . King Kutter , Inc. (“King Kutter”), P .O. Box 1200, Winfield, Alabama 35594, warrants to the original ret ail purchaser (“Purchaser”) that the product that is the subject of this sale is free from defects in material and workmanship at the time of sale.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il King Kutter Rotary Mower è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del King Kutter Rotary Mower - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso King Kutter Rotary Mower imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul King Kutter Rotary Mower ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il King Kutter Rotary Mower, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del King Kutter Rotary Mower.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il King Kutter Rotary Mower. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo King Kutter Rotary Mower insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
