Manuale d’uso / di manutenzione del prodotto KV-V8 del fabbricante JVC
Vai alla pagina of 27
MOBILE VIDEO CASSETTE PLAYER No.49625 Feb. 2001 COPYRIGHT 2001 VICTOR COMPANY OF JAPAN, LTD. KV-V8 Area Suffix E J Continental Europe Nor th America Contents q Specifications q CA UTION q Instructions 1. DISASSEMBL Y 1.1 Disassembly flo w char t 1-1 1.
Specificatios (KV -V8J) General •Power supply : DC12 V (1 1V -16V allowable)Negative ground •Dimensions : 259 mm x 94 mm x 270 mm (10-1/4"x 3-3/4"x 10-1 1/16") (width x height x depth) •Mass : 3.
1-1 [1] Top cover D1 2(S1a), (S1b), 2(S1c) [2] SW board assembly, D2 2(S2a), (WR2a), stay <Note 2a> Front panel assembly 4(L2a), 3(L2b), <Note 2b> CN3006(WR2b) [3] Cassette housing D3a, 2(.
1-2 Fig. D2 Fig. D3b Fig. D3a Fig. D1 Rear side Pinch plate Loading motor belt Control cam Hole align with hole in deck <Note 3a> (S3a) (L3a) (L3a) [3] Cassette housing assembly Switch lev er RE.
1-3 Fig. D4 Fig. D6 Fig. D5 Not used Inertia plate [4] Drum assembly (S4b) < e > (L5a) WR4a Supporting tape side <Note 2a> WR4b Supporting tape side <Note 2a> CN1 Not used (S4a) (S4c.
1-4 Fig. 1-4-1a Main board assembly SW board assembly Front board assembly CN3006 CP5001 CP5002 CN7001 TP7002 GND TP7001 MECHA TEST TP111 D .FF TP4001 CTL.P TP106 PB FM TP2253 A FM 1.5 Mechanism service mode This model has a unique function to enter the mechanism into every operation mode without loading of any cassette tape.
1-5 1.6 Emergency display function This unit has a function for storing the history of the past two emergencies (EMG) and displaying them on each FDP (or OSD). With the status of the VCR and mechanism at the moment an emergency occurred can also be confirmed.
1-6 1.6.3 EMG content description Note: EMG contents “ E08/E09 ” are for the model with Dynamic Drum (DD). Table 1-6-3a When the mechanism mode cannot be changed to an- other mode even when the loading motor has rotated for more than 4 seconds in the loading direction, [E:01] is identified and the power is turned off.
1-7 1.6.4 EMG detail information <1> The status (electrical operation mode) of the VCR and the sta- tus (mechanism operation mode/sensor information) of the mechanism in the latest EMG can be confirmed based on the figure in EMG detail information <1> .
1-8 -0 -7 - Initial value -1 -0 - EJECT position - - -0 EJECT position (Cassette housing drive mode) -2 -7 - Housing operating - - -1 Between EJECT and U / L STOP -3 -1 -2 U / L STOP position - - -3 G.
2-1 SECTION 2 MECHANISM ADJUSTMENT 2.1 Before starting repair and adjustment 2.1.1 Precautions (1) Unplug the power cord plug of the VCR before using your soldering iron. (2) Take care not to cause any damage to the conductor wires when plugging and unplugging the connectors.
2-2 2.1.5 Maintenance and inspection 1. Location of major mechanical parts Fig. 2-1-5a Mechanism assembly top side Fig. 2-1-5b Mechanism assembly bottom side Control Cam Lever Assembly Guide Arm Assem.
2-3 2. Cleaning Regular cleaning of the transport system parts is desirable but practically impossible. So make it a rule to carry out clean- ing of the tape transport system whenever the machine is serviced.
2-4 2.2 Replacement of major parts 2.2.1 Before starting disassembling This mechanism has an exclusive operation mode provided for disassembling and installation of the mechanism (Mecha- nism assembling mode), and it is suggested to set the mechanism to this mode before disassembly and installation.
2-5 2.2.6 Loading motor (1) Remove the belt from the worm gear assembly. (2) Take out the 2 screws (A) and then remove the loading motor. Note: • When installing the loading motor, hold it so that the label faces upward. Also take care with the wire colors.
2-6 Fig.2-2-9b 2.2.10 Control plate (1) Take out the slit washer, disengage the 2 hooks while lifting the control cam side of the control plate, and re- move the control plate. Notes: • After removing the control plate, be careful not to turn the main deck assembly upside down.
2-7 2.2.13 Change lever assembly, rotary encoder (1) Slide the change lever assembly in the direction of the arrow and remove. (2) While pushing the claws on both sides in the disengag- ing directions, take out the rotary encoder. (3) When attaching the rotary encoder, position it so that the alignment markings face each other as shown in Fig.
2-8 2.2.16 Guide rail (1) Take out the 5 screws (A) and 1 screw (B). (2) By expanding the rails on the outer sides of the guide rail, remove the 2 pole base assemblies (supply, take up). (3) Disengage the 4 claws and remove the guide rail. Note: • Before removing the guide rail, it is required to remove the drum assembly.
2-9 2. How to install (1) Clean the coil parts of the lower drum assembly and the newly installed upper drum assembly with an air brush in advance. (See Fig.2-2-19b.) (2) Install a new washer and upper drum assembly on the drum shaft. (See Fig.2-2-19a.
2-10 Fig. 2-3-2a 2.3.2 Loading arm assemblies (supply, take up) (1) Attach the loading arm assembly (supply) and loading arm assembly (take up) so that the alignment markings on their gears face each other and the holes on their arms are respectively aligned with the holes on the main deck.
2-11 2.3.5 Control plate (1) Attach the control plate by aligning the 2 alignment holes on the control plate with the alignment holes on the main deck assembly as well as the alignment holes on the take up lever. As the take up lever is pulled by a tension spring, use a pair of tweezers or similar too to align the holes.
2-12 Fig. 2-5-1a Improper waveform variation Max level Min level Proper waveform variation Fig. 2-5-1b 1.25mm Roller driver Hexagonal wrench Tighten Loosen Guide roller 2.5 Compatibility adjustment Notes: • Although compatibility adjustment is very important, it is not necessary to perform this as part of the nor- mal servicing work.
2-13 Fig. 2-5-1d Improper Proper ( a ) Guide roller ( b ) Guide pole Fig. 2-5-1c A B C D Level drop at the guide roller (supply side) Level drop at the guide roller (take-up side) • Proper waveform variation: Always flat • Improper waveform variation: Higher Lower 2.
2-14 2.5.4 Standard tracking preset Fig. 2-5-3b Fig. 2-5-3a Alignment tape [SP, stairstep] played with the SP head Alignment tape [EP(LP), stairstep] played with the EP(LP) head Drum side Control head.
3-1 SECTION 3 ELECTRICAL ADJUSTMENT 3.1 Precaution The following adjustment procedures are not only necessary after replacement of consumable mechanical parts or board assemblies, but are also provided as references to be re- ferred to when servicing the electrical circuitry .
3-2 3.2.2 Slow tracking preset Signal (A1) • Color (colour) bar or stairstep signal [KV-V8E] (A2) • Alignment tape [MH-2] or [MHPE] (A3) • Alignment tape [MH-2L] or [MHPE-L] [KV-V8J] (A2) • Al.
Printed in Japan 200102(S) No.49625 VICTOR COMPANY OF JAPAN, LIMITED MOBILE ELECTRONICS DIVISION PERSONAL & MOBILE NETWORK BUSINESS UNIT. 10-1,1Chome,Ohwatari-machi,Maebashi-city,Japan KV-V8.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il JVC KV-V8 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del JVC KV-V8 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso JVC KV-V8 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul JVC KV-V8 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il JVC KV-V8, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del JVC KV-V8.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il JVC KV-V8. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo JVC KV-V8 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
