Manuale d’uso / di manutenzione del prodotto BR-DV600E del fabbricante JVC
Vai alla pagina of 24
This instruction book is made from 100% recycled paper. INSTRUCTIONS VIDEO CASSETTE RECORDER BR-DV600U SL96179 For Customer Use: Enter below the Serial No. which is located on the bottom of cabinet. Retain this information for future reference. Model No.
2 1. Read all of these instructions. 2. Save these instructions for later use. 3. All warnings on the product and in the operating instructions should be adhered to. 4. Unplug this appliance system from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
3 CAUTION ATTENTION RISK OF ELECTRIC SHOCK DO NOT OPEN RISQUE D’ELECTROCUTION NE PAS OUVRIR INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
4 CONTENTS 1 INTRODUCTION 1-1 Major Features ............................................. 5 1-2 Maintenance ................................................ 5 1-3 Precautions .................................................. 6 2 CONTROLS, CONNECTORS AND DISPLAYS 2-1 Front Panel .
6 1-3 Precautions Handling 5 Do not block the ventilation openings. 5 Do not place anything heavy on the unit. 5 Do not put any foreign materials into the cassette loading slot. 5 Operate the unit in a horizontal (flat) position only . 5 Avoid violent shocks to the unit.
8 2-2 Rear Panel 2 CONTROLS, CONNECTORS AND DISPLA YS DC 12V PGZ01945 TIMER TIME CODE SPARE COMPONENT VIDEO SYNC IN REC OFF PLAY DV IN/OUT REMOTE AUDIO 2 1 SERIAL CH 1/3 OUT OUT IN IN B-Y IN Y/C LINE .
11 3-1 Video system connections 3 CONNECTIONS Connecting a monitor The on-screen display can be viewed on a monitor con- nected to the [VIDEO MONITOR OUT] connector . Connecting video equipment Connect the video device to the appropriate connector (4 types are available).
12 DC 12V PGZ01945 TIMER TIME CODE SPARE COMPONENT VIDEO SYNC IN REC OFF PLAY DV IN/OUT REMOTE AUDIO 2 1 SERIAL CH 1/3 OUT OUT IN IN B-Y IN Y/C LINE OUT OUT MONITOR CH 2/4 MONITOR OUT R-Y Y 3-2 Audio system connections 3 CONNECTIONS Audio output from a VCR, etc.
14 EDITING CONTROL UNIT RM-G800 EDIT MODE ENTRY MENU CANCEL GOTO IN OUT ENTRY SHI FT PREVIEW REVIEW AUTO EDIT ALL STOP GPI MANUAL TAKE COUNTER TC HOLD TC CTL UB PRESET ASSEM VIDEO/Hi-Fi AUD-1 AUD-2 IN.
16 Recorder BR-DV600 BR-DV600 BR-S800 SR-S365 (U MODEL) SR-S388 (E MODEL) BR-DV600 Player BR-DV600 BR-DV600 BR-DV600 BR-DV600 BR-S800/BR-S500 (+ SA-N50)* 5 Edit adjust setting The No. 353 <EDIT ADJUST> menu switch must be adjusted according to the configuration of the editing system being used.
18 4 MENU SWITCHES 4-2 Menu switch details For switch setting procedures, refer to “ Menu switch setting procedure ” . q : Factory setting (00): The number in the bracket shows the set value on the counter display . 002 OPERA TION LOCK Details: Switches the operation lock ON/OFF .
20 4 MENU SWITCHES 4-2 Menu switch details 502 CHARACTER V .POSITION Details: Moves the display position of the tape counter on screen, etc. vertically .
22 Built-in clock setting Time data is recorded in the sub code area of the tape during recording. In the Play mode, this data is read out and can be shown on the on-screen display or the counter display . 5 PREP ARA TION 5 Setting procedure The names of the operation buttons are shown above the buttons.
24 PHONES MIC REMOTE LOCAL EJECT OPERATE REC LEVEL CH-2/4 CH-1/3 SHIFT SET SELECT SHIFT MENU HOLD AUDIO MONITOR OUTPUT COUNTER SHIFT A. DUB ADVANCE PRESET L CTL TC UB CH-1/2 CH-3/4 R MIX MIX REW STOP .
26 8 EXTERNAL TIMER-ST ART FUNCTION DC 12V PGZ01945 TIMER TIME CODE SPARE COMPONENT VIDEO SYNC IN REC OFF PLAY DV IN/OUT REMOTE AUDIO 2 1 SERIAL CH 1/3 OUT OUT IN IN B-Y IN Y/C LINE OUT OUT MONITOR CH 2/4 MONITOR OUT R-Y Y REC: Timer recording OFF: Timer function OFF PLA Y: Timer playback Commercially available timer, etc.
28 9 TIME CODE Set the menu switches. ( See page 20.) 5 Set the No. 414 <TCG SELECT> menu switch to “ PRESET ” . 5 Set the No. 415 <TCG MODE> menu switch. Setting is not necessary for user bits. REC RUN: The time code is counted only during recording.
30 10 SUPER SCENE FINDER FUNCTION Preparation Connect the 9-pin D-sub connector of the installed SA-K46 RS-232C interface board to a personal computer , etc. with an RS-232C cable. Use a reverse type cable. For RS-232C interface settings, refer to “ RS-232C specifications ” on page 32.
32 11-2 RS-232C specifications 9PIN D-Sub 1 23 4 5 6 9 Pin NO. Signals Operations Direction of signals 2 RXD Receive data VTR p PC 3 TXD Transmit data VTR [ PC 4 DTR Data terminal ready VTR [ PC 5 GND Signal ground 6 DSR Data set ready VTR p PC Note: PC means a controller such as a personal computer.
34 11 RS-232C INTERF ACE Commands Description B6 R-SHUTTLE Shuttle reverse play . The search speed is specified by sending the speed code data after this command (see the table above). C4 FULL EE ON Full EE mode ON C5 FULL EE OFF Full EE mode OFF CA REC Record.
36 11 RS-232C INTERF ACE Contents of ST A TUS SENSE When the ST ATUS SENSE (D7H) command is sent, the following data (5 bytes) is returned. First byte Bit No. Status When the bit is 1 7 Always 1 6 Always 0 5 SHORT FF/REW D uring short FF or short REW 4 REC INHIBIT Recording is inhibited.
38 11 RS-232C INTERF ACE Menu switch setting command ED MEMORY SW PRESET Use this command to change the VCR ’ s menu switches. Transmit the data (3 bytes) corresponding to the menu switch to be changed, following this command. (e.g.) Set No. 108 <VIDEO INPUT SELECT> menu switch to “ COMPONENT ” .
40 12 TROUBLESHOOTING 12-1 Warning indicators If the unit malfunctions during operation, the built-in self-diagnostics system identifies the problem and displays a warning message on the monitor and/or the counter display . Also, the [AUTO OFF] indicator may be shown on the LCD.
42 12-2 Other problems Action • Set the [REMOTE] switch to “ LOCAL ” . • Set the No. 002 <OPERA TION LOCK> menu switch to “ OFF ” . • Connect the monitor to the [MONIT OR OUT] connector . • Set the No. 500 <ON SCREEN> menu switch to “ ON ” .
44 Precautions for Use of Head Cleaning Tape Adhere to the following precautions when using the head cleaning tape. 1. The tape runs for 10 seconds at a time in the PLAY mode. (The tape stops automatically.) Press the PLAY button after the cleaning tape is fully loaded.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il JVC BR-DV600E è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del JVC BR-DV600E - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso JVC BR-DV600E imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul JVC BR-DV600E ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il JVC BR-DV600E, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del JVC BR-DV600E.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il JVC BR-DV600E. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo JVC BR-DV600E insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
