Manuale d’uso / di manutenzione del prodotto DC-650A del fabbricante Jet Tools
Vai alla pagina of 20
Operating Instructions and Parts Manual Dust Collector Model: DC-650A/C/ARC/CRC DC-650ARC shown DC-650C shown WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60123 Part No.
2 This manual has been pre pared for the owner and operato r s of the JET DC-650 Series Dust Collectors. I ts purpose, aside from machine operatio n, is to prom ote safety using accepted operatin g and maintenance procedures.
3 Table of Contents Warranty and Service ........................................................................................................... ................................ 2 Table of Contents .................................................
4 Warnings 1. Read and understand the entire o wners manual before attempting assembly or operation. 2. Read and un derstand the warnings posted on the machi ne and in this manual. Failure to co mply with all of these warnings may cause serious inju ry.
5 blahblahblah 20. Make your workshop child proof with padlocks , master switc hes or by removing starter keys. 21. Give your work undivided attention. Loo king arou nd, carrying on a conversation a nd “horse-play” are careless acts that can result in seriou s injury.
6 Introduction This manual is provided by JET covering the safe operation and maintenan ce procedures for models DC-650 Series Dust Collectors. This manual contains in structions on installation, safety pre cautions, general operating procedures, maintenance in structions and par ts breakdown.
7 Unpacking 1. Remove all contents fr om the shipping carton. 2. Report any damage to your distributor. 3. Do not discard any shipping material until after the dust collector has been assembl ed and is running properly.
8 Assembly The dust collector must be disconnected from the po wer source during assembly . Failure to comply may result in serious injury! Motor Housing and Support Canister 1. Place the impeller housing (A, Fig. 1) on the floor with the motor (B, Fig.
9 Filter Bag Installation – DC-650A/ARC 1. Thread an M6 hex nut onto the filter bag support rod, followed by an M6 fl at washer and M6 lock washer (A, Fig. 5). Thread the support rod (B, Fig. 5) into the motor/fan housin g and tighten nut against the housing.
10 Canister Installation – DC-650C/CRC 1. Place the canister filter so that it fits snugly over the housing and tighten the four knobs (A, Fig. 7). 2. Mount handle (B, Fig. 7) to the arm (C, Fig. 7) with a M8 flat washer (D, Fig. 7), M8 lock washer (E, Fig.
11 Electrical Connections All electrical connections must be done by a qualified electrician. All adjustments or repairs must be done with the dust collector disco nnected from the power source, unplugged. Failu re to comply may result in serious injury! The DC-650 series dust collectors are rated at 115/230V, Prewired 115V .
12 Maintenance Never perform maintenance on this machine before turning switch off and removing plug from power source. Failure to comply may cause serious injury! Cleaning the Filter Bag – DC-650A/ARC Wearing a particle mask/respirator for protection against fin e dust particles during cleaning is highly recommended.
13 Parts Replacement Parts Replacement parts are li sted in the Parts List on the following pages. To orde r parts or reach our service department, call 1-800-274-68 48 between 7:00 a.
14 Index No. Part No. Description Size Qty 35 ............. 331010 ..................... Shaft ....................................................................................................................... 1 36 ............. 331043 ..........
15 Parts Breakdown for DC-650C/ CRC Models for DC-650A/AR C Models.
16 Remote Control Breakdown for DC-650ARC/CRC Index No. Part No. Description Size Qty ................. DC650RC-100 ......... Rec eiver As sembly (Ite ms 1-11) ............................................................ ................ 1 1 .........
17 Wiring Diagrams DC-650A/C Models 115V 230V.
18 DC-650ARC/CRC Models.
19 Notes.
20 WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60123 Phone: 800-274-6848 www.wmhtoolgroup.co m.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Jet Tools DC-650A è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Jet Tools DC-650A - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Jet Tools DC-650A imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Jet Tools DC-650A ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Jet Tools DC-650A, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Jet Tools DC-650A.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Jet Tools DC-650A. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Jet Tools DC-650A insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
