Manuale d’uso / di manutenzione del prodotto GTS600 del fabbricante JBL
Vai alla pagina of 16
either subwoofer or component speakers in a bi-amplified system, or conventional full-range speakers in simpler systems. The GTS300 and 600 also include preamp-level outputs which can provide either full-range, high-pass or low-pass signal to drive additional amplifiers.
2 before disconnecting the battery! 2. Run a minimum A WG #8 power cable complete with a 40 amp fuse (not included) for the GTS300 or an A WG #6 or A WG #4 cable with an 80 amp fuse for the GTS600 directly from the positive + 12V battery terminal to the disir ed amplifier location.
9. Fuse – 40 Amp A TC type fuse for the GTS300 and two 40 amp fuses for the GTS600. 10. Gain Control – Use this contr ol to adjust the input sensitivity of the amplifier .
3. System Design Using the GTS300 or GTS600: 3.1 Speaker Requirements When used in the non-bridged mode the GTS300 or GTS600 can easily drive 2 ohm speaker loads. When only one speaker is connected to each channel, virtually any conventional speaker may be used.
components is extremely important for proper performance and long term reliability . All wiring connections should be made either by soldering with heatshrink tubing insulation or with high quality crimp type insulated connectors installed with a good crimping tool.
5. Internal Adjustments Speaker -Level Input Impedance Adjustments The speaker level inputs of the GTS300 and GTS600 come factory set with 100K ohm input impe- dance.
Regardless of whether you build or buy it, the necessary resistor network has the following configuration: Custom “Chip” Construction • Each resistor in the package has the same value.
6. Input Gain Adjustment Before operating the GTS300 or GTS600, recheck all wiring connections to make sure they are correct and secure. Be sure that a fuse (40 amp for GTS300 and two 40 amp fuses for the GTS600, not included) is installed in the +12V line near the battery .
7. T ypical Applications The following diagrams show the most common basic system configurations of the GTS300 and GTS600. A combination of one or more of these “building blocks” may be combined to form elabo- rate system designs.
10 L– R+ – + L– R+ – + L– R+ – + Preamp or Speaker-Level Input L R 2 or 4-Ohm Full-Range Speakers L– L+ – + R– R+ – + L R Front Rear 4-Ohm Subwoofer Stereo Subwoofers may be used by configuring Amp B as shown in Application #1 .
Simultaneous Stereo-Mono Connection Diagrams 11 L– L+ L L L R R R – + L– R+ – + R– R+ – + 2 or 4-Ohm Full-Range Speakers 4-Ohm Subwoofer Amp Crossover Input Mode Preamp Switch Switch Outpu.
8. In Case of Difficulty Power -on light does not come on Power light is on, but no sound is heard from some or all of the speakers • Head unit not on; turn the head unit on. • Ground wire is disconnected or defective; check for continuity with an ohm-meter between the amplifier’ s ground terminal and a know chassis ground point.
Power On light is blinking, indicating a fault condition, and sound is intermittent or off Alternator whine through the audio system with the engine running Bass output from speakers too low • Defective GTS300 or GTS600; If ther e is audio signal present at the input of the amplifier and there is no output, the GTS300 or GTS600 may be defective.
9. Specifications Specifications Power Output (10Hz -50kHz, 14.4V Battery V oltage Signal to Noise Ratio Fr equency Response Damping Factor Line Level Input Sensitivity (For Rated Power) Line Level In.
15 Specifications Power Requirement Fuse Size Size (L x W x H) W eight Speaker Level Input Mating Connector GTS300 11 to 16V DC Negative Ground 40 Amp A TC T ype Fuse 13 1/4”x 9 1/4”x 2” (337 mm x 235 mm x 51 mm) 10 lbs 8.5 oz (4.8 Kg) Molex Mini-Fit Jr .
16 DECLARA TION OF CONFORMITY W e, Harman Marketing Europe a/s Kongevejen 194B DK-3460 Birkerød DENMARK declare that the product described in this owner’ s manual is in compliance with technical standards: EN 55020, EN 6.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il JBL GTS600 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del JBL GTS600 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso JBL GTS600 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul JBL GTS600 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il JBL GTS600, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del JBL GTS600.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il JBL GTS600. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo JBL GTS600 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.