Manuale d’uso / di manutenzione del prodotto T-270 del fabbricante Interfire Audio
Vai alla pagina of 20
MONO CHANNEL / 2 CHANNEL / 4 CHANNEL AUTOMOTIVE AMPLIFIER INSTRUCTION MANUAL T-1000M T-270 / T -2100 / T-2130 T-460 / T -480 By.
.
1 free installation. Congratulations on your Purchase • Four Class ''AB'' High-Current Dual Discrete Drive Stages. • Class ''AB'' T echnology MOSFET PWM Power Supply . • Bridgeable & TRI-Mode Operation.
• NEVER operate the amplifier without the proper power and ground wire, 10 gauge minimum. • NEVER operate the amplifier without proper fusing. Fuse holder must be located with in 0.5 meters from the battery . This fuse is to protect the car not the electronics.
INSTALLA TION 1. After reading precaution, decide where you are going to install the unit. Also, see Fig.1. 2. Once the location has been determined, place the amplifier into position. Using a felt tip pen or pencil mark the four holes to be drilled for mounting.
POWER CONNECTIONS CONNECTIONS INPUT CONNECTIONS It is important to have good quality power and ground connections. Remember , to complete an electrical circuit, the ground connection is just as important as the positive power connection.
5 FIG.2 MONO CHANNEL SYSTEM WIRING DIAGRAM AUTO - ANTENNA LEAD CH1 CH2 CAR STEREO HEAD UNIT B + GND REM LINE IN LINE OUT REMOCON GAIN BASS L.P.F PHASE 6V 0.
6 2 CHANNEL SYSTEM WIRING DIAGRAM FIG.2 B + GND REM AUTO - ANTENNA LEAD CH1 CH2 CAR STEREO HEAD UNIT LINE IN LINE OUT REMOCON L.P.F L.P.F H.P.F H.P.F 6V 0.
7 FIG.2 B + GND REM 4 CHANNEL SYSTEM WIRING DIAGRAM CH3 CH4 CH2 CH1 AUTO - ANTENNA LEAD CAR STEREO HEAD UNIT LINE IN LINE IN GAIN GAIN BASS BASS CROSSOVER CROSSOVER 6V 0.2V 0dB 12dB 50Hz 500Hz CH1 CH2 CH3 CH4 50Hz 500Hz 0dB 12dB 6V 0.2V CH 1/2 CH 3/4 FLAT L.
ON PROTECT POWER B + GND REM FUSE SPEAKER This amplifier can operate in one, two or three channel mode. The minimum impedance for single channel (bridged/mono) operation is 4 or 8 ohms. Tri channel power is referred to stereo and mono at the same time.
ON PROTECT POWER B + GND REM FUSE CH1 CH2 BRIDGED SPEAKER ON PROTECT POWER B + GND REM FUSE CH1 CH2 BRIDGED SPEAKER 2 CH SPEAKER WIRING DIAGRAM 2 - 4 Ohm 1 CH 2 CH 1 SPEAKER BRIDG ED 2 SPEAKER STER EO 3 SPEAKER TRI MODE 4 - 8 Ohm 1CH ON PROTECT POWER B + GND REM FUSE CH1 CH2 BRIDGED SPEAKER FIG.
4 CH SPEAKER WIRING DIAGRAM 2 S PEAKER BRIDGED 2 S PEAKER + 1 SUBWOOFER 4 S PEAKER STEREO 6 S PEAKER HEX MODE 10 SPEAKER CONNECTIONS SPEAKER BRIDGED CH1 CH3 CH2 CH4 ON PROTECT POWER B + GND REM FUSE S.
11 ADJUSTMENTS 1.Set to the "H.P .F" position when the amplifier is used to drive a tweeter/midrange system. The frequencies below the crossover point will be attenuated at 12dB/octave. Permits adjustment of the crossover frequency ,by rotating the knob to select any frequency 2.
FRONT/REAR P ANEL 12 2CHANNEL ON PROTECT POWER B + GND REM FUSE CH1 CH2 BRIDGED SPEAKER 30A TUNN T-270 By LINE IN LINE OUT L.P.F L.P.F H.P.F H.P.F 6V 0.2V 0dB 12dB 50Hz 250Hz FLAT 80Hz 1.2KHz CROSSOVER CH1 CH2 CH1 CH2 BASS GAIN ON PROTECT POWER B + GND REM FUSE CH1 CH2 BRIDGED SPEAKER 25A 25A T-2100 By TUNN LINE IN LINE OUT REMOCON L.
FRONT/REAR P ANEL 13 4CHANNEL MONO CHANNEL LINE IN LINE IN GAIN GAIN BASS BASS CROSSOVER CROSSOVER 6V 0.2V 0dB 12dB 50Hz 500Hz CH1 CH2 CH3 CH4 50Hz 500Hz 0dB 12dB 6V 0.
14 This section provides you with a catalog of amplifier symptoms and their probable causes and solutions. Before you consult this listing, make sure the vehicle's electrical system is working properly by verifying that other electrical items (e.
NOTE : Specifications & design subject to change without notice for improvements. SPECIFICATI ON SPECIFICATI ON 100W x 2 160W x 2 50Hz-250Hz 900 Watts YES >100 <0.1% HP/FULL/LP 270 15 T-2 70 Output Power Rating RMS Channel Total Max Power 4 Ohm at 14.
NOTE : Specifications & design subject to change without notice for improvements. SPECIFICATI ON SPECIFICATI ON 330W x 1 510W x 1 50Hz-250Hz 1200 Watts YES >150 <0.1% N / A 330 N / A 16 T-1 000M Output Power Rating RMS Channel Total Max Power 4 Ohm at 14.
Please call TUNN Customer Service at 1- 877-90-AUDIO to obtain an RA # (Return Authorization number). All warranty returns applied to products. (TUNN will not be WARRANTY WARRANT Y LIMIT ATIONS The following is NOT covered under TUNN warranty program: NOTICE: Products shipped without a valid RA # will be refused and shipped back.
10110 Santa Fe Springs Road Santa Fe Springs, CA 90670 1-562-926-2600.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Interfire Audio T-270 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Interfire Audio T-270 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Interfire Audio T-270 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Interfire Audio T-270 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Interfire Audio T-270, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Interfire Audio T-270.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Interfire Audio T-270. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Interfire Audio T-270 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
