Manuale d’uso / di manutenzione del prodotto POD-6552 del fabbricante Intel
Vai alla pagina of 90
POD-6552 5.25” Intel® Celeron® M SBC, with CPU/ VGA/LCD, and Ether- net Interface User ’ s Manual.
POD-6552 User’s Manual ii Copyright This document is copyrighted, © 20 05. All rights are reserved. The origi- nal manufacturer reserves the right to make improvem ents to the products described in this manual at any time wi thout notice.
iii Packing List Before you begin installing your card, please make su re that the following materials have been shipped: • 1 POD-6552 all-in one single board computer • Mini Jumper(yellow) p/n : .
POD-6552 User’s Manual iv Model No. List Description POD-6552L-M0A1 C-M 600 MHzM(0L2) SBC LAN/VGA / LCD/TV/A T Eco POD-6552F-M0A1 Same as POD- 6552L-M0A1,w/cable/ DSTN/ AT X POD-6552L-00A1 Same as POD-6552L-M0A1,but wit h SKT479 A d d i t i o n a l I n f o r m a t i o n a n d A s s i s ta n c e V isit the Advantech web site at www .
v FCC This device complies with the re quirements in part 15 of the FCC rules: Operation is subject to the following two conditio ns: 1.This device may n ot cause harmful interfer- ence, and 2.
POD-6552 User’s Manual vi.
vii Contents Chapter 1 General Information ........................................ 2 1.1 Introduction ............ ............................ ............ ........... ........ 2 1.2 Features ............. ................ ................. ........
POD-6552 User’s Manual viii 2.19 COM port connector (CN2,CN9) ................... ................. 19 2.20 PS/2 Mouse/Keyboard connect or (CN5)........ ........... ...... 20 2.20.1 PS/2 connector(CN13) .......... ............ ........... ..........
ix Figure 4.6:Power Management Setup ............ ............. .. 34 4.2.7 PnP/PCI Confi gurations ...... .............. ........... ........... ...... 35 Figure 4.7:PnP/P CI Configurations ................... ........... 35 4.2.8 Freque ncy/Voltage Control.
POD-6552 User’s Manual x A.9 USB port 4, 5(CN11)...... ................. ................. ............... 60 Table A.9:USB 4, 5 connector(C N11).......................... 60 A.10 LVDS connector(CN14)......... ................. ................... .
xi B.4 Interrupt assignments .............. ................. .................... ... 74 Table B.4:Interrupt as signments ........... ........... ............. 74 Appendix C Programming the Watchdog Timer ............. 76 C.1 Supported Input Timing Modes .
POD-6552 User’s Manual xii.
1 Chapter 1 General Information 1 General Information This chapter gives background information on the POD -6552. Sections include: • Introduction • Features • Specifications • Board layout an.
POD-6552 User’s Manual 2 Chapter 1 General Information 1.1 Introduction The POD-6552 is a new Intel® Celeron® M 600 MHz(0L2) 5.25" Bis- cuit PC with enhanced graphics fu nction. The POD-6552 comes with an embedded high-performance Celeron® M 600 MHz processor on-board, and one socket479 optional for Celero n-M CPU.
3 Chapter 1 General Information 1.3 Specifications 1.3.1 St andard SBC Functions • CPU: Intel® Celeron® M 600 MHz w/ o L2 cache. Socket479(Optional for Celeron® M and Pentium® M CPU) • System .
POD-6552 User’s Manual 4 1.3.3 Solid S t ate disk • Supports CompactFlash T y pe I/II disks 1.3.4 TV -Out • Chipset: C hrontel CH7009 • Supports TV outpu t • Supports NTSC and P AL formats • Supports s-video • TV output supports graphics resolutio ns up to 1024x768 pixels 1.
5 Chapter 1 General Information 1.4 Board layout: dimensions Figure 1.1: Board layout: dimensions (comp onent side).
POD-6552 User’s Manual 6 Figure 1.2: Board layout: di mensions (solder side).
7 Chapter 2 Installation 2 Inst allation This chapter explains the setup procedures of POD-6552 hardware, including instruc- tions on setting jumpers and con necting peripherals, switches and indicators. Be sure to read all safe ty precautions before you begin the i nstallation procedure.
POD-6552 User’s Manual 8 Chapter 2 Inst allation 2.1 Jumpers The POD-6552 has a number of jum pers that allow you to configure y our system to suit your application.
9 Chapter 2 Installation 2.2 Connectors On-board connectors link the POD -6552 to external devices such as hard disk drives, a keyboard, or floppy drives.
POD-6552 User’s Manual 10 2.3 Locating Connectors(component side) CN26 Front Panel connector CN27 Floppy connector CN28 Print connector F AN 1,2 FAN connector PCI 1,2 PCI slot Figure 2.
11 Chapter 2 Installation 2.4 Locating Connectors(solder side) Figure 2.2: Connectors (solder side).
POD-6552 User’s Manual 12 2.5 Setting Jumpers Y ou may configure your card to match the needs of you r application by setting jumper s. A jumper is a metal br idge used to close an electric cir- cuit. It consists of two metal pi ns and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them.
13 Chapter 2 Installation 2.6 Clear CMOS (J8) This jumper is used to erase CMOS data and reset system BIOS informa- tion. The procedure for clearing CMOS is: 1.
POD-6552 User’s Manual 14 2.7 COM2 232/422/485 Select(J1/J2/J3/J4) 2.8 Setting LCD V oltage(J5) T able 2.4: COM2 232/422/485 Sel ect(J1) RS232 RS422 RS485 1-2(Default) 3-4 5-6 T able 2.5: COM2 232/422/485 Sel ect(J2/J3/J4) RS232 RS422/RS485 J2(1)-J3(1) J3(1)-J4(1) J2(2)-J3(2) J3(2)-J4(2) J2(3)-J3(3) J3(3)-J4(3) J2(4)-J3(4) J3(4)-J4(4) T able 2.
15 Chapter 2 Installation 2.9 SM BUS Connector(J6) 2.10 PCI VIO(J7) 2.1 1 Inst alling DDR SODIMMs The procedure for installing DDR SODIMMs appears below . Please follow these steps carefully . 1. Make sure that all power supplies to the system are switched off 2.
POD-6552 User’s Manual 16 3. Slip the DDR SODIMM into the so cket at a 45 de gree angle and care- fully fit the bottom of the card against the connectors. 4. Gently push the DDR SODIMM into a perpendicul ar position until the clips on the ends of the DDR SODIMM sockets snap into place.
17 Chapter 2 Installation of a 34-pin flat-cable connector (usually used for 3. 5” drives) and a printed-circuit board connector (usually used fo r 5.25” drives). 2.14.1 Connecting the floppy drive 1. Plug the 34-pin flat-cable connector i nto CN27.
POD-6552 User’s Manual 18 1. Connect one end of the cable to CN25,CN24. Make sure that the red (or blue) wire corresponds to pin 1 on the connector , which is labeled on the b oard (on the right si de). 2. Plug the other end of the cable in to the Enhanced IDE hard drive, with pin 1 on the cable corresponding to pin 1 on the hard drive.
19 Chapter 2 Installation 2.16.4 TTL LCD/DSTN connector(CN17) CN17 is a 40-pin connector for TTL LCD or DSTN. It could connect TTL LCD or DSTN freely to meet your need. 2.17 USB connectors (CN4,CN1 1,CN12) The POD-6552 board provides up to six USB (Universal Serial Bu s) ports.
POD-6552 User’s Manual 20 mouse, etc.) or a communication netw ork. Y ou can find the pin assign- ments for the COM port connecto r in Appendix A. 2.20 PS/2 Mouse/Keyboard connector (CN5) The POD-6552 board p rovides a keyboard connector that supp orts both a keyboard and a PS/2 style mous e.
21 Chapter 2 Installation 2.21.6 Lan Active LED(Pin 7 & Pin 8) The LED would light when the Lan is active. 2.21.7 Lan Linked LED(Pin 9 & Pin10) The LED would light when the Lan is linked.
POD-6552 User’s Manual 22 2.25 IR Connector(CN10)(Optional) This connector suppo rts the optional wireless infrared transmitting and receiving module. This mo dule mounts on the system case. Y ou must configure th setting through B IOS se tup. Detailed pin definition you will find in Appen dix A.
CHAPTER 3 Sof tware Configuration This chapter details the software con- figuration information . It shows you how to configure the card to match your application requirements.
POD-6552 User’s Manual 24 Chapter 3 Sof tware Configuration 3.1 Introduction The system BIOS and custom drivers are located in a 512 KB, 32-pin (JEDEC spec.) Flash ROM device, designated U28. A single Flash chip holds the system BIOS, VGA BIOS, and network Boot ROM image.
25 Chapter 3 2. At th e prompt, t ype A WDFLASH .EXE and press <Enter>. The VGA configuration program will then display the followi ng: 3. At the prompt, enter the new BIN file which suppo rts your display . When you are sure that you have entered the file name correctly press <Enter>.
POD-6552 User’s Manual 26 3.3.1 AU M170EG01(1280 x1024 L VDS LCD) T a ble 3.1: Connections to LCD/Flat Pannel (CN14) LCD Connector Flat Pannel Connector JAE FI-X30C2L DF13-40P Pin Signal Pin Signal .
27 Chapter 4 Ducks that N eed Love! 4 A ward BIOS Setup This chapter describes how to set BIOS configuration data. CHAP TER.
POD-6552 User’s Manual 28 Chapter 4 A ward BIOS Setup 4.1 System test and initialization These routines test and initialize bo ard hardware. If the routines encoun- ter an error during the tests, you wil l either hear a few short beeps or see an error message on the sc reen.
29 4.2 Award BIOS setup A ward’ s BIOS ROM h as a built-in Set up program that allows users to modify the basic system configu ration. This type of inform ation is stored in battery-backed CMOS RAM so that it reta ins the Setup in formation when the power is turned off.
POD-6552 User’s Manual 30 4.2.2 St andard CMOS Features setup When you choose the Standard CMOS Features option from the Initial Setup Screen menu, the screen shown belo w is displayed. This standard Setup Menu allows users to configure system components such as date, time, hard disk drive, floppy drive and display .
31 4.2.3 Advanced BIOS Features setup By choosing the Advanced BIOS Features Setup op tion from the Initial Setup Screen menu, the sc reen below is displayed. This sample screen contains the manufacturer ’ s defaul t values for the POD-6552 Series. Figure 4.
POD-6552 User’s Manual 32 4.2.4 Advanced Chip set Features setup By choosing the Advanced Ch ipset Features option from the Initial Setup Screen menu, the screen below is displayed. This sample screen contains the manufacturer ’ s default va lues for the POD-6552 Series.
33 4.2.5 Integrated Peripherals Choosing the Integrated Peripheral s option from the Initial Setup Screen menu should prod uce the screen belo w . Here we see the manufacturer ’ s default values for the POD-655 2 Series.
POD-6552 User’s Manual 34 4.2.6 Power Management Setup By choosing the Power Manage ment Setup option from the Initial Setup Screen menu, the screen below is displayed. This sample screen contains the manufacturer ’ s default va lues for the POD-6552 Series.
35 4.2.7 PnP/PCI Configurations By choosing the PnP/PCI Configu rations option from the Initi al Setup Screen menu, the screen below is displayed. This sample screen contains the manufacturer ’ s default va lues for the POD-6552 Series.
POD-6552 User’s Manual 36 4.2.8 Frequency/V olt age Control By choosing the Frequency/V oltage Control option from the Initial Setup Screen menu, the screen below is displayed. This sample screen contains the manufacturer ’ s defau lt values for the POD-6552 Figure 4.
37 4.2.9 Load Optimized Default s Load Optimi zed Defaults loads the default system values directly from ROM. If the stored record created by the Setup program should ever become corrupted (and therefore unusabl e), these defaults will load auto- matically when you turn th e POD-6552 Series system on.
POD-6552 User’s Manual 38 4.2.10 Set Password T o Establish P assword 1. Choose the Set Passw ord option from t he CMOS Setup Utility main menu and press <Enter>. 2. When you see “Enter Password,” enter the desired password and press <Enter>.
39 T o Change Password 1. Choose the Set Passw ord option from t he CMOS Setup Utility main menu and press <Enter>. 2. When you see “Enter Password,” enter the existing password and press <Enter>. 3. Y ou will see “Confi rm Password.
POD-6552 User’s Manual 40 T o Disable Password 1. Choose the Set Passw ord option from t he CMOS Setup Utility main menu and press <Enter>. 2. When you see “Enter Password,” enter the existing password and press <Enter>. 3. Y ou will see “Confi rm Password.
41 If you select this option and press <Y > then <Enter>, the values entered in the setup utilities will be reco rded in the chipset ’ s CMOS memory . The microprocessor will check this every time you turn your syst em on and use the settings to configure the syst em.
POD-6552 User’s Manual 42.
CHAPTER 5 PCI SVGA Setup Introduction Installation of SVGA drivers -for W indows XP Further information.
POD-6552 User’s Manual 44 Chapter 5 PCI SVGA Setup 5.1 Introduction The board has an onboard interface. The specificat ions and features are described as follows: 5.1.1 Chip set The POD-6552 uses a Intel 852GM + ICH4 chipset for its graphic con- troller .
45 Chapter 5 5.2 Inst allation of the SVGA Driver Complete the followin g steps to install the SVGA driver . Follow the pro- cedures in the flow char t that apply to the operating syst em that you are using within your board.
POD-6552 User’s Manual 46 2. Press the "Next" button. 3. Press the "Next" button..
47 Chapter 5 4. In order to continue setup, you must accept the agreement, press the "Y es" button and wait a minute. 5. Choose the option "Y es, I want to restart my computer now .
POD-6552 User’s Manual 48 5.3 Further Information For further information about the AGP/VGA installation in yo ur POD- 6552, includi ng driver updates, tro ubleshooti ng guides and F AQ lists, visit the following web resources: Intel websit e: www .
49 Chapter 6 CHAPTER 6 Audio Setup • Introduction • Installation of audio driver fo r W i n- dows XP.
POD-6552 User’s Manual 50 Chapter 6 Audio Setup 6.1 Introduction The POD-6552 supports AC97 stereo sound without Amplifier and sup- ports speaker-out, CD-input, Line-in, Line-out and Microphone.. 6.2 Driver inst allation 6.2.1 Before you begin Please read the instructions in this chapter carefully before you attem pt installation.
51 Chapter 6 2. Press the "Next" button and wait for a moment. 3. Choose the option "Continue Anyw ay”..
POD-6552 User’s Manual 52 4. Choose the option "Y es, I w ant to restart my computer now", then click "Finish" button to reboot your computer .
53 Appx. A A Pin Assignment s This appendix contains information of a detailed or specialized nature. It includes: • Floppy Drive Connector • Primary IDE Connect or • LP T Connector • Secondar.
POD-6552 User’s Manual 54 Appendix A Pin Assignment s A.1 A TX power connector (CN23) T a ble A.1: A TX po wer connector(CN23) Pin Signal 1 5VSB 2N C 3P S _ O N 1 23.
55 Appx. A A.2 Floppy connector (CN27) T a ble A.2: Floppy Connector (CN27) Pin Signal Pin Signal 1G N D 2 R W C # 3G N D 4 N C 5G N D 6 D S 7 GND 8 Index# 9G N D 1 0 M O A # 1 1 GND 12 DSB# 13 GND 14.
POD-6552 User’s Manual 56 A.3 Primary IDE Connector (CN25) T a ble A.3: Primary IDE connector (CN25) Pin Signal Pin Signal 1 IDE RESET 2 G ND 3D 7 4D 8 5D 6 6D 9 7D 5 8D 1 0 9D 4 1 0 D 1 1 1 1 D3 12.
57 Appx. A A.4 Secondary IDE Connector (CN24) T a ble A.4: Secondary IDE connector (CN24) Pin Signal Pin Signal 1 IDE RESET 2 G ND 3D 7 4D 8 5D 6 6D 9 7D 5 8D 1 0 9D 4 1 0 D 1 1 1 1 D3 12 D12 13 D2 14.
POD-6552 User’s Manual 58 A.5 CompactFlash socket(CN22) T a ble A.5: CompactFlash socket (CN22) Pin Signal Pin Signal 1 GND 26 #CD1 2D 3 2 7 D 1 1 3D 4 2 8 D 1 2 4D 5 2 9 D 1 3 5D 6 3 0 D 1 4 6D 7 3.
59 Appx. A A.6 LAN,RJ45 connector(CN6) A.7 USB port 0, 1(CN4) A.8 USB port 2, 3(CN12) T a ble A.6: LAN,RJ45 connector(CN6) 10/100M Pin Signal Pin Signal 1T X + 5N C 2T X - 6R X - 3R X + 7N C 4N C 8N C T a ble A.7: USB 0, 1 connector(CN4) Pin Signal Pin Signal 1+ 5 V 2+ 5 V 3 USB0- 4 USB1- 5 USB0+ 6 USB1+ 7 USB GND 8 USB GND 9 GND 10 NC T a ble A.
POD-6552 User’s Manual 60 A.9 USB port 4, 5(CN1 1) T a ble A.9: USB 4, 5 connector(CN1 1) Pin Signal Pin Signal 1+ 5 V 2+ 5 V 3 USB0- 4 USB1- 5 USB0+ 6 USB1+ 7 USB GND 8 USB GND 9 GND 10 NC 3 6 4 5 .
61 Appx. A A.10 L VDS connector(CN14) T a ble A.10: L VDS co nnector (CN14) Pin Signal Pin Signal 1 VCC_LCD 2 VCC_LCD 3 GND 4 GND 5 L VDS0 _N0 6 L VDS0_P0 7 GND 8 L VDS0_N1 9 L VDS0_P1 10 GND 11 LV D .
POD-6552 User’s Manual 62 A.1 1 Print port connector(CN28) A.12 COM port 1, 2 Connector (CN2) T a ble A.1 1: Prin t port connecto r(CN28) Pin Signal Pin Signal 1S T B # 2A F D # 3D 0 4E R R 5 D1 6 I.
63 Appx. A A.13 COM port 3, 4 Connector (CN9) T a ble A.13: COM port 3,4 Connector(CN9) Pin Signal Pin Signal 1 DCD3 2 DSR3 3S I N 3 4 R T S 3 5 SOUT3 6 CTS3 7D T R 3 8 R I 3 9G N D 1 0 G N D 1 1 D CD.
POD-6552 User’s Manual 64 A.14 Audio connector(CN8) A.15 D-SUB VGA connector(CN1) T a ble A.14: Audio connector(CN8) Pin Signal Pin Signal 1 Right S peak out+ 2 Right speak out- 3 Left speak out+ 4 .
65 Appx. A A.16 VGA connector(CN7) A.17 IrDA connector(CN10) A.18 LCD Backlight connector(CN15) T a ble A.16: VGA connector(CN7) Pin Signal Pin Signal 1R 2+ 5 V 3G 4G N D 5B 6N C 7 NC 8 D2_DA T A 9 GND 10 HS 11 G N D 1 2 V S 13 GND 14 D2_ CLOCK 15 GND 16 NC T a ble A.
POD-6552 User’s Manual 66 A.19 PS/2 connector(CN13) A.20 CD-In connector(CN16) A.21 PS/2 Mouse/Keyboard connector(CN5) T a ble A.19: PS/2 connector(CN13) Pin Signal Pin Signal 1 PS/2 KB CLOCK 2 PS/2 KB DA T A 3 PS/2 MOUSE CLOCK 4 GND 5 +5V 6 PS/2 MOUSE DA T A T a ble A.
67 Appx. A A.22 TTL LCD or DS TN connector(CN17) T a ble A.22: TTL LCD or DSTN connector (CN17) Pin Signal Pin Signal 1 VCC_LCD 2 VCC_LCD 3G N D 4G N D 5 VCC_LCD 6 VCC_LCD 7N C 8G N D 9P D 0 1 0 P D 1.
POD-6552 User’s Manual 68 A.23 ISA slot(CN19) T a ble A.23: ISA slot Connector (CN19) Pin Signal Pin Signal A1 IOCHECK B1 GND A2 SD7 B2 RESETDRV A3 SD6 B3 +5V A4 SD5 B4 IRQ9 A5 SD4 B5 -5V A6 SD3 B6 .
69 Appx. A A.24 EBX Power connector(CN20) A.25 -5V and -12V connector(CN21) T a ble A.24: EBX connector(CN20) Pin Signal Pin Signal 1+ 5 V 2 G N D 3G N D 4 + 1 2 V 5- 1 2 V 6 G N D 7+ 5 V T a ble A.
POD-6552 User’s Manual 70 A.26 Front Panel connector(CN26) T a ble A.26: Front Panel connector(CN26) Pin Signal Pin Signal 1 +5V 2 HDD_LED 3+ 5 V 4 G N D 5S U S L E D 6G N D 73 .
71 Appx. B B System Assignment s This appendix contains information of a detailed n ature. It inclu des: • System I/O ports • 1st MB memory map • DMA channel assignments • Interru pt assignmen.
POD-6552 User’s Manual 72 Appendix B System Assignment s B.1 System I/O Port s T a ble B.1: System I/O port s Addr . range (Hex) D evice 00-0F Master DMA controller 20-21F Mas ter Interrupt co ntrol.
73 Appx. B B.2 1st MB memory map B.3 DMA channel assignment s CF8-CFB PCI Configuration Address CFC-CFF PCI Configuration Data D00-FFFF -available for system use- T a ble B.
POD-6552 User’s Manual 74 B.4 Interrupt assignment s T a ble B.4: Interrupt assignments Interrupt# Interrupt source IRQ 0 Interval timer IRQ 1 Keyboard IRQ 2 Interrupt from controller 2 (cascade) IR.
Appendix C Programming the W atchdog T imer The board is equipped with a watchdog timer that resets the CPU or gener ates an interrupt if processing comes to a standstill for any reason. This feature ensures system reliability in industrial standalone or unmanned environm ents.
Pod-6552 User’s Manual 76 Appendix C Programming the W atchdog Ti m e r C.1 Supported Input Timing Modes In order to program the watchdog tim er, you must write a program which writes I/O port address 866 (hex). The output data is a value of time inter- val.
77 Appendix C The following example sh ows how you might program the watchd og timer in ASSEMBL Y : ;Watchdog timer example program MOV DX, 865H ; set the time unit as second MOV AL, 80H OUT DX, AL MO.
Pod-6552 User’s Manual 78.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Intel POD-6552 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Intel POD-6552 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Intel POD-6552 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Intel POD-6552 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Intel POD-6552, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Intel POD-6552.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Intel POD-6552. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Intel POD-6552 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
