IT
InFocus logo
Manuale d'uso ufficiale

InFocus VR 9DM2

130 pagine·2.4 MB·Avvitatore a impulsi·PDF·ENJA
InFocus VR 9DM2
Indice dei contenuti 28 sezioni Variable speed · WH12DM2 WR12DM2 WH12DMR · GENERAL OPERATIONAL PRECAUTIONS · PRECAUTIONS FOR CORDLESS IMPACT DRIVER · … MostraNascondi
Page 1 of the InFocus VR 9DM2 user manual — WH12DM2 WR12DM2 WH12DMR
Pagina 1 · clicca per ingrandire
Pagina 1

Cordless Impact Driver/Wrench Akku-Schlagschrauber Perceuse/visseuse à percussion sur batterie Avvitatore a impulso a batteria per viti e bulloni Snoerloze slagschroevendraaier/sleutel Atornillador/Llave de impacto a batería Aparafusadora/ Chave de impacto a bateria ¢Ú··ÓÔηÙÛ¿‚È‰Ô ª·Ù·Ú›·˜/∫ÏÂȉ›

Variable speed

  • WH 12DM2
  • WR 12DM2
  • WH 12DMR WH 9DM2
  • WR 9DM2
InFocus VR 9DM2 — Variable speed diagram (page 1)
Fig. 1 · Variable speed

WH12DM2 WR12DM2 WH12DMR

Read through carefully and understand these instructions before use. Diese Anleitung vor Benutzung des Werkzeugs sorgfältig durchlesen und verstehen. Lire soigneusement et bien assimiler ces instructions avant usage. Prima dell’uso leggere attentamente e comprendere queste istruzioni. Deze gebruiksaanwijzing s.v.p. voor gebruik zorgvuldig doorlezen. Leer cuidadosamente y comprender estas instrucciones antes del uso. Antes de usar, leia com cuidado para assimilar estas instruções. ∆ιαάστε πρ σεκτικά και καταν ήσετε αυτές τις δηγίες πριν τη ρήση.

Handling instructions Bedienungsanleitung Mode d’emploi Istruzioni per l’uso Gebruiksaanwijzing Instrucciones de manejo Instruções de uso δηγίες ειρισµ ύ

Page 2 of the InFocus VR 9DM2 user manual — Variable speed
Pagina 2 · clicca per ingrandire
Pagina 2
InFocus VR 9DM2 — Variable speed diagram (page 2)
Fig. 2 · Variable speed
InFocus VR 9DM2 — Variable speed diagram (page 2)
Fig. 3 · Variable speed
InFocus VR 9DM2 — Variable speed diagram (page 2)
Fig. 4 · Variable speed
InFocus VR 9DM2 — Variable speed diagram (page 2)
Fig. 5 · Variable speed
Page 3 of the InFocus VR 9DM2 user manual — Variable speed
Pagina 3 · clicca per ingrandire
Pagina 3
InFocus VR 9DM2 — Variable speed diagram (page 3)
Fig. 6 · Variable speed
InFocus VR 9DM2 — Variable speed diagram (page 3)
Fig. 7 · Variable speed
Page 4 of the InFocus VR 9DM2 user manual — Variable speed
Pagina 4 · clicca per ingrandire
Pagina 4
InFocus VR 9DM2 — Variable speed diagram (page 4)
Fig. 8 · Variable speed
InFocus VR 9DM2 — Variable speed diagram (page 4)
Fig. 9 · Variable speed
Page 5 of the InFocus VR 9DM2 user manual — Variable speed
Pagina 5 · clicca per ingrandire
Pagina 5
EnglishDeutschFrançaisItaliano 112 V Rechargeable battery (For WH12DM2, WR12DM2, WH12DMR)Akkumulator, 12 V (Für WH12DM2, WR12DM2, WH12DMR)Batterie rechargeable, 12 V (Pour WH12DM2, WR12DM2, WH12DMR)Batteria ricaricabile, 12 V (Per WH12DM2, WR12DM2, WH12DMR) 29.6 V Rechargeable battery (For WH9DM2, WR9DM2)Akkumulator, 9,6 V (Für WH9DM2, WR9DM2)Batterie rechargeable, 9,6 V (Pour WH9DM2, WR9DM2)Batteria ricaricabile, 9,6 V (Per WH9DM2, WR9DM2) 3LatchSchnapperLoquetFermo 4HandleeGriffPoignéeImpugnatura 5InsertEinsatzInsérerInserire 6Pull outHerausziehenTirerEstrarre 7InsertEinsetzInsérerInserire 8Pilot lampKontrollampeLampe piloteSpia 9Hole for connecting the rechargeable batteryAnschlußlon für AkkumulatorOrifice de raccordement de la batterie rechargeableForo di collegamento della batería recargable 0MovementBewegungMouvementMovimento AGuide sleeveFührungsmanschetteManchon-guideManicotto guida BHexagonal hole in the anvilSechskantloch in der SchabotteOrifice hexagonal de la chabotteForo esagonale nel basaménto CDriver bitDreherspitzeMècheTesta avvitatrice DHexagonal socketSechskantbuchseDouille hexagonalChiave de incavo esagonale EGrooveSchlitzRainureScanalature FAnvilSchabotteChabotteBasamento GPinStiftGoupilleSpina HRingRingAunneauAnello IHoleÖffnungOrificeForo JPlungerPreßkolbenPistonStantuffo KRetaining ringHalteringBague de retenueAnello di trattenimento LHookHakenCrochetGrancio MSpringFederRessortMolla NLarger diameter faces awayDer große Durchmesser weist zur anderen SeiteGros diamètre dirigé vers l’extérieurDiametro più grande lontano da sé OSwitchSchalterInterrupteurInterruttore PPhillips-head screwdriverKreuzschlitzschraubenzieherTournevis à tête PhillipsCacciavite con testa a croce QScrewSchraubeVisVite RArrowPfeilFlècheFreccia SHook coverHakenabdeckungCache de crochetCoperchio gancio TIndentationEinkerbungEntailleTacca UProtuberanceVorsprungSaillieSporgenza VAAAA batteriesBatterien der Größe AAAAPiles AAAAPile AAAA WPush buttonDruckknopfPoussoirTasto da premere XPushDrückenPousserSpingere YWear limitVerschließgrenzeLimite d'usureLimite di usura ZNail of carbon brushKlaue der KohlebürsteClou de balai en carboneChiodo di spazzola di carbone [Protrusion of carbon brushKrempe der KohlebürsteSaillie de balai en carboneSporgenza di spazzola di carbone \Contact portion outside brush tubeKontaktteil außerhalb des BürstenrohrsSection de contact à l’extérieur du tube de balaiParte di contatto fuori dal tubo spazzola
Page 6 of the InFocus VR 9DM2 user manual — Variable speed
Pagina 6 · clicca per ingrandire
Pagina 6
NederlandsEspañolPortuguêsΕλληνικά 1Oplaadbare batterij, 12 V (Voor WH12DM2, WR12DM2, WH12DMR)Batería recargable, 12 V (Para WH12DM2, WR12DM2, WH12DMR)Bateria de 12 V recarregável (Para WH12DM2, WR12DM2, WH12DMR)12 V Επανα ρτιµενη µπαταρία (Για WH12DM2, WR12DM2, WH12DMR) 2Oplaadbare batterij, 9,6 V (Voor WH9DM2, WR9DM2)Batería recargable, 9,6 V (Para WH9DM2, WR9DM2)Bateria de 9,6 V recarregável (Para WH9DM2, WR9DM2)9,6 V Επανα ρτιµενη µπαταρία (Για WH9DM2, WR9DM2) 3VergrendelingEngancheLingüetaΜάνδαλ 4HandgreepMangoCaboερ ύλι 5InstekenInsertarInserirΕισωρήστε 6UittrekkenSacarRetirarΒρα ή τε έ ω 7InstekenInsertarInserirΕισωρήστε 8KontrolelampjeLámpara pilotoLâmpada piloto∆ κιµαστική λάµπα 9Aansluiting voor oplaadbare batterijAgujero para conectar la batería recargableOrifício para conectar a bateria recarregávelΤρύπα για την σύνδεση της επανα ρτιµενης µπαταρίας 0BewegingMovimientoMovimentoΚίνηση AGeleide ringManguito guíaManga-guia%δηγητικς ραί νας BZeshoekige opening in het draaistukOrificio hexagonal en el yunqueOrifício sextavado na bigornaΕ άγωνη τρύπα στ ν άκµ να CSchroefstukPunta de destornilladorChave de fendaΛεπίδα κίνησης DZeschoekige busRecaptáculo hexanogalEncaixe longoΜακριά υπ δ ή EGroefRanuraRanhuraΑυλάκωση FDraaistukYunqueBigornaΆκµ νας GPenPasadorPinoΠείρ ς HRingAnilloAnel∆ακτύλι ς IOpeningOrificioOrifícioΤρύπα JPlunjerEmboloPistãoΈµ λ KBorgringAnillo de retenciónAnel de retenção∆ακτύλι ς συγκράτησης LHaakGanchoGanchoΆγκιστρ MVeerResorteMolaΕλατήρι NDe grotere diameter wijst van u vandaanEl diámetro más grande queda en dirección opuestaO diâmetro maior dá para foraΗ µεγαλύτερη διάµετρ ς λέπει πρ ς άλλη κατεύθυνση OSchakelaarInterruptorComutador∆ιακπτης PKruiskopschroevendraaierDestornillador con cabeza PhillipsChave PhillipsΚατσα ίδι κε αλής Phillips QSchroefTornilloParafusoΒίδα RPijlFlechaSetaΒέλ ς SAfdekking haakCubierta del ganchoTampa do ganchoΚάλυµµα αγκίστρ υ TInkepingIndentaciónEntalheΑυλάκωση UUitsteekselSalienteProtuberânciaΠρ ε ή VAAAA batterijenPilas AAAAPilhas AAAAΑΑΑΑ µπαταρίες WDruktoetsPulsadorInterruptorΚ υµπί ώθησης XDrukkenPresionarApertarΣπρώ ε YSlijtagegrensLímite de usoLimite de desgaste5ρι θ ράς ZNagel van koolborstelUña de escobilla de carbónPrego da escova de carvãoΚαρ ί καρ υνακι ύ [Uitsteeksel van koolborstelSaliente de escobilla de carbónSaliência da escova de carvãoΠρ ε ή καρ υνακι ύ \Contact-gedeelte buiten de borstelbuisTubo exterior de la parte de contacto de la escobilla de carbónSegmento de contato no exterior do tubo da escovaΤµήµα επα ής έ ω απ τ σωλήνα της ψήκτρας
Page 7 of the InFocus VR 9DM2 user manual — PRECAUTIONS FOR CORDLESS IMPACT DRIVER
Pagina 7 · clicca per ingrandire
Pagina 7

GENERAL OPERATIONAL PRECAUTIONS

24. Always charge the battery before use. 25. Never use a battery other than that specified. Do not connect a usual dry cell, a rechargeable battery other than that specified or a car battery to the power tool. 26. Do not use any transformer that has a booster. 27. Do not charge the battery from an engine electric generator or DC power supply. 28. Always charge indoors. Because the charger and battery heat slightly during charging, charge the battery in a place not exposed to direct sunlight; where the humidity is low and the ventilation is good. 29. Before starting to work in a high place, pay attention to the activities below to make sure there are no people below. 30. Use the exploded assembly drawing on this handling instructions only for authorized servicing. 31. If the supply cord is damaged, it must be replaced by the manufacture or its service agent or a similarly qualified person in order to avoid a hazard.

1. Keep work area clean. Cluttered areas and benches invite accidents. 2. Avoid dangerous environment. Don’t expose power tools and charger to rain. Don’t use power tools and charger in damp or wet locations. And keep work area well lit. Never use power tools and charger near flammable or explosive materials. Do not use tool and charger in presence of flammable liquids or gases. 3. The appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure that they do not play with the appliance. All visitors should be kept safe distance from work area. 4. Store idle tools and charger. When not in use, tools and charger should be stored in dry, high or locked-up place – out of reach of the children and infirm persons. Store tools and charger in a place where the temperature is less than 40°C. 5. Don’t force tool. It will do the job better and safer at the rate for which it was designed. 6. Use right tool. Don’t force small tool or attachment to do the job of a heavy duty tool. 7. Wear proper apparel. Do not wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves and non-skid footwears are recommended when working outdoor. 8. Use eye protection with most tools. Also use face or dust mask if cutting operation is dusty. 9. Don’t abuse cord. Never carry charger by cord or yank it to disconnect from receptacle. Keep cord from heat, oil and sharp edges. 10. Secure work. Use clamps or a vise to hold work. It’s safer than using your hand and it frees both hands to operate tool. 11. Don’t overreach. Keep proper footing and balance at all times. 12. Maintain tools with care. Keep tools sharp at all times, and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 13. When the charger is not in use, or when being maintained and inspected, disconnect its power cord from the receptacle. 14. Remove chuck wrenches and wrenches. Form habit of checking to see that wrenches are removed from tool before turning it on. 15. Avoid accidental starting. Don’t carry tool with finger on switch. 16. To avoid danger, always use only the specified charger. 17. Use only genuine HITACHI replacement parts. 18. Do not use power tools for applications other than those specified in the Handling Instructions. 19. To avoid personal injury, use only the accessories or attachment recommended in these handling instructions or in the HITACHI catalog. 20. Let only the authorized service center do the repairing. The Manufacturer will not be responsible for any damages or injuries caused by repair by the unauthorized persons or by mishandling of the tool. 21. To ensure the designed operational integrity of power tools and charger, do not remove installed covers or screws. 22. Always use the charger at the voltage specified on the nameplate. 23. Do not touch movable parts or accessories unless the power source has been disconnected.

PRECAUTIONS FOR CORDLESS IMPACT DRIVER

1. This is portable tool for tightening and loosenig screws. Use it only for these operation. 2. Use the earplugs if using for a long time. 3. One-hand operation is extremely dangerous; hold the unit firmly with both hands when operating. 4. After installing the driver bit, pull lightly out the bit to make sure that it does not come loose. If the bit is not installed properly, it can come loose during use, which can be dangerous. 5. Use the bit that matches the screw. 6. Tightening a screw with the impact driver at an angle to that screw can damage the head of the screw and the proper force will not be transmitted to the screw. Tighten with this impact driver lined up straight with the screw. 7. Always charge the battery at a temperature of 0 – 40°C. A temperature of less than 0°C will result in over charging which is dangerous. The battery cannot be charged at a temperature greater than 40°C. The most suitable temperature for charging is that of 20 – 25°C. 8. Do not use the charger continuously. When one charging is completed, leave the charger for about 15 minutes before the next charging of battery. 9. Do not allow foreign matter to enter the hole for connecting the rechargeable battery. 10. Never disassemble the rechargeable battery and charger. 11. Never short-circuit the rechargeable battery. Short-circuiting the battery will cause a great electric current and overheat. It results in burn or damage to the battery. 12. Do not dispose of the battery in fire. If the battery burnt, it may explode. 13. Do not insert object into the air ventilation slots of the charger. Inserting metal objects or inflammables into the charger air ventilation slots will result in electrical shock hazard or damaged charger. 14. Bring the battery to the shop from which it was purchased as soon as the post-charging battery life becomes too short for practical use. Do not dispose of the exhausted battery. 15. Using an exhausted battery will damage the charger.

Page 8 of the InFocus VR 9DM2 user manual — SPECIFICATIONS
Pagina 8 · clicca per ingrandire
Pagina 8

PRECAUTIONS FOR CORDLESS IMPACT WRENCH

You could get hurt or the movement of the socket could shake the impact wrench so much as to make you drop it. 10. Always charge the battery at a temperature of 0 – 40°C. A temperature of less than 0°C will result in over charging which is dangerous. The battery cannot be charged at a temperature greater than 40°C. The most suitable temperature for charging is that of 20 – 25°C. 11. Do not use the charger continuously. When one charging is completed, leave the charger for about 15 minutes before the next charging of battery. 12. Do not allow foreign matter to enter the hole for connecting the rechargeable battery. 13. Never disassemble the rechargeable battery and charger. 14. Never short-circuit the rechargeable battery. Short-circuiting the battery will cause a great electric current and overheat. It results in burn or damage to the battery. 15. Do not dispose of the battery in fire. If the battery burnt, it may explode. 16. Do not insert object into the air ventilation slots of the charger. Inserting metal objects or inflammables into the charger air ventilation slots will result in electrical shock hazard or damaged charger. 17. Bring the battery to the shop from which it was purchased as soon as the post-charging battery life becomes too short for practical use. Do not dispose of the exhausted battery. 18. Using an exhausted battery will damage the charger.

1. This is a portable tool for tightening and loosening bolts and nuts. Use it only for these operation. 2. Use the earplugs if using for a long time. 3. One-hand operation is extremely dangerous; hold the unit firmly with both hands when operating. 4. Check that the socket is not cracked or broken. Broken or cracked sockets are dangerous. Check the socket before using it. 5. Secure the socket with the socket pin and the ring. If the socket pin or ring securing the socket is damaged, the socket may come off from the impact wrench, which is quite dangerous. Do not use socket pins or rings that are deformed, worn out, cracked, or in any other way damaged. Always make sure to install the socket pin and ring in the correct position. 6. Check the tightening torque. The appropriate torque for tightening a bolt depends on the material the bolt is made of, its dimensions, grade, etc. Also, the tightening torque generated by this impact wrench depends on the materials and dimensions of the bolt, how long the impact wrench is applied for the way in which the socket is installed, etc. Also the torque when the battery has just been charged and when it is about to run out are slightly different. Use a torque wrench to check that the bolt has been tightened with the appropriate torque. 7. Stop the impact wrench before switching the direction of rotation. Always release the switch and wait for impact wrench to stop before switching the direction of rotation. 8. Never touch the turning part. Do not allow the turning socket section to get near your hands or any other part of your body. You could be cut or caught in the socket. Also, be careful not to touch the socket after using continuously it for a long time. It gets quite hot and could burn you. 9. Never let the impact wrench turn without a load when using the universal joint. If the socket turns without being connected to a load, the universal joint causes the socket to turn wildly.

MODEL

WH12DM2: with charger and case WH9DM2: with charger and case WH12DMR: with charger and case WR12DM2: with charger and case WR9DM2: with charger and case

SPECIFICATIONS

ModelWH9DM2 (9.6 V)WH12DM2 (12 V)WH12DMR (12 V) No-load speed0 – 2800 min–10 – 2600 min–1 CapacityM4 – M8 (Small screw) M5 – M12 (Ordinary bolt) M5 – M10 (High tension bolt) Tightening torqueMaximum 80 N·m {820 kgf·cm} Tightening is M12 high tension bolt (strength grade 12.9), when fully charged at 20°C temp. Tightening time: 3 sec.Maximum 135 N·m {1375 kgf·cm}Maximum 130 N·m {1330 kgf·cm} Tightening is M14 high tension bolt (strength grade 12.9), when fully charged at 20°C temp. Tightening time: 3 sec. Rechargeable batteryEB9B: Ni-Cd battery, 9.6 V (2.0 Ah 8 cells)EB1220BL: Ni-Cd battery, 12 V (2.0 Ah 10 cells) EB926H: Ni-MH battery, 9.6 V (2.6 Ah 8 cells)EB1226HL: Ni-MH battery, 12 V (2.6 Ah 10 cells) EB930H: Ni-MH battery, 9.6 V (3.0 Ah 8 cells)EB1230HL: Ni-MH battery, 12 V (3.0 Ah 10 cells) Weight1.2 kg1.6 kg

Cordless Impact Driver

Page 9 of the InFocus VR 9DM2 user manual — OPTIONAL ACCESSORIES (Sold separately)
Pagina 9 · clicca per ingrandire
Pagina 9
ModelWR9DM2 (9.6 V)WR12DM2 (12 V) No-load speed0 – 2600 min–1 CapacityM6 – M14 (Ordinary bolt) M6 – M16 (Ordinary bolt) M6 – M10 (High tension bolt) M6 – M12 (High tension bolt) Tightening torqueMaximum 120 N·m {1220 kgf·cm} Tightening is M12 high tension bolt (strength grade 12.9), when fully charged at 20°C temp. Tightnening time: 3 sec.Maximum 165 N·m {1685 kgf·cm} Tightening is M16 (F10T), when fully charged at 20°C temp. Tightening time: 3 sec. Rechargeable batteryEB9B: Ni-Cd battery, 9.6 V (2.0 Ah 8 cells)EB1220BL: Ni-Cd battery, 12 V (2.0 Ah 10 cells) EB930H: Ni-MH battery, 9.6 V (3.0 Ah 8 cells)EB1230HL: Ni-MH battery, 12 V (3.0 Ah 10 cells) Weight1.4 kg1.6 kg

CHARGER

ModelUC14YFA Charging timeEB9B, EB1220BL: Approx. 50 min. (at 20°C) EB926H, EB1226HL: Approx. 65 min. (at 20°C) EB930H, EB1230HL: Approx. 70 min. (at 20°C) Charging voltage7.2 – 14.4 V Weight0.6 kg
Part NameEngraved charactersLBCode No. 10 mm Hexagonal socket (small type)146514996180 10 mm Hexagonal socket166516996181 10 mm Hexagonal socket176517996182 1/2" Hexagonal long socket2116621996197

STANDARD ACCESSORIES

1. Charger (UC14YFA) 1 2. Plastic case 1 Standard accessories are subject to change without notice.

OPTIONAL ACCESSORIES (Sold separately)

<For WH12DM2, WH9DM2, WH12DMR> 1. Plus driver bit

InFocus VR 9DM2 — OPTIONAL ACCESSORIES (Sold separately) diagram (page 9)
Fig. 10 · OPTIONAL ACCESSORIES (Sold separately)
Bit No.Code No. No. 2992671 No. 3992672 2. Hexagonal socket Part NameEngraved charactersLBCode No. 5 mm Hexagonal socket8658996177 6 mm Hexagonal socket106510985329 5/16" Hexagonal socket126512996178 8 mm Hexagonal socket136513996179
InFocus VR 9DM2 — OPTIONAL ACCESSORIES (Sold separately) diagram (page 9)
Fig. 11 · OPTIONAL ACCESSORIES (Sold separately)
3. Wood working drill: Code No. 959183
InFocus VR 9DM2 — OPTIONAL ACCESSORIES (Sold separately) diagram (page 9)
Fig. 12 · OPTIONAL ACCESSORIES (Sold separately)
4. Drill chuck adapter set: Code No. 321823 Use the drills available on the local market.
InFocus VR 9DM2 — OPTIONAL ACCESSORIES (Sold separately) diagram (page 9)
Fig. 13 · OPTIONAL ACCESSORIES (Sold separately)

Cordless Impact Wrench · Engraved characters

Page 10 of the InFocus VR 9DM2 user manual — CHARGER
Pagina 10 · clicca per ingrandire
Pagina 10

<For WR12DM2, WR9DM2> 1. Sockets

InFocus VR 9DM2 — CHARGER diagram (page 10)
Fig. 14
Square head drive dimensions S (mm)Part NameCode No.Suitable Bolt Diameter High ISO ISO Inch tension (ordinary) (small) bolts fHexagonal width across lats H (mm)FormMain Socket Dimensions (mm) High tension (oISO I rdinary) (sSO mall) L L1 øF 12.7Hexagonal Socket10 mm944291M610B408 18 12 mm873632M8 W5/16"12B408 20 13 mm873539M813B409 25 14 mm873540M1014B409 25 17 mm873536M10M12W3/8"17C328 28 19 mm873624M12M14 W7/16"19C349 28 21 mm873626W1/2"21D36 10 32 22 mm873627M12M14M1622D40 14 35 24 mm873629M16M1824D40 15 38
InFocus VR 9DM2 — CHARGER diagram (page 10)
Fig. 15

<For WR9DM2> Table 2

Square head drive dimensions S (mm)Part Name Code No.Suitable Bolt Diameter ISO ISO Inch w (ordinary) (small) bolts flaHexagonal idth across ts H (mm)FormMain Socket Dimensions (mm) ISO (ordinarISO y) (small L L1 øF H 9.5exagonal Socket8 mm996125M58B335 13 10 mm996126M610B336 16 12 mm996127M8W5/16"12C337 19 13 mm996128M813B338 20 14 mm996129M1014B338 21 16 mm996130M1016D339 24 17 mm996131M10M12W3/8"17D33 10 25 18 mm996132M1218D33 10 26 19 mm996133M12W7/16"19D33 12 27.5
InFocus VR 9DM2 — CHARGER diagram (page 10)
Fig. 16
2. Long Socket
InFocus VR 9DM2 — CHARGER diagram (page 10)
Fig. 17

<For WR12DM2> · Table 1

Page 11 of the InFocus VR 9DM2 user manual — CHARGER
Pagina 11 · clicca per ingrandire
Pagina 11
Square head drive dimensions S (mm)Part NameCode No.Suitable Bolt DiameterHexagonal width acros flats H (mms Form )Main Socket Dimensions (mm) High tensionISO (ordinary)ISO (small)Inch bolts LL1L2øF 12.7Long Socket12 mm955138M8W5/16"12B52203420 13 mm955139M813B52203421.5 14 mm955140M1014B52203422 17 mm955141M10M12W3/8"17B52243425 17 mm955149M10M12W3/8"17B75245725 19 mm955142M12M14W7/16"19B52243428 19 mm955150M12M14W7/16"19B75245728 21 mm955143W1/2"21D52243431 21 mm955151W1/2"21D75245731 21 mm991480W1/2"21D1252410731 22 mm955144M12M14M1622D52243432.5 24 mm955146M16M1824D52253434

<For WR9DM2> Table 4

Square head drive dimensions S (mm)Part NameCode No.Suitable Bolt DiameterHexagonal width acros flats H (mms Form )Main Socket Dimensions (mm) ISO (ordinary)ISO (small)Inch bolts LL1L2øF 9.5Long Socket8 mm996134M58B60124813 10 mm996135M610B60124816 12 mm996136M8W5/16"12C60144818.4 13 mm996137M813B60144818.9 14 mm996138M1014B60154819.5 16 mm996139M1016D60154824 17 mm996140M10M12W3/8"17D60154825 18 mm996141M1218D60164826 19 mm996142M12W7/16"19D60174827.5
3. Extension bar: WR12DM2: Code No. 873633 WR9DM2: Code No. 996143 The extension bar is convenient for working in very restricted spaces or when the socket provided cannot reach the bolt to be tightened. CAUTION:
5. Duct Socket: (WR12DM2) This is used for tightening bolts and nuts on flange sections of air conditioners, type ducts, etc.

When the extension bar is used, the tightening torque is reduced slightly compared with the ordinary socket.

Code No.Hexagonal width across flats (mm) 99365812 99261313 99261514
4. Universal joint: WR12DM2: Code No. 992610 WR9DM2: Code No. 996147 The universal joint is convenient for impacting nuts when there is an angle between the socket and wrench, or when working in a very narrow space.
6. Corner attachment (Model EW-14R) (WR12DM2) Use this attachment only when the machine is applied to the nut or bolt at the right angle.

<For WR12DM2> · Table 3

Page 12 of the InFocus VR 9DM2 user manual — APPLICATION
Pagina 12 · clicca per ingrandire
Pagina 12
7. Bit adaptor: Code No. 322752 (WR12DM2) This is used for tightening small screws (M6 – M8). NOTE: (1) This adaptor is set only on the anvil (drive angle) of

BATTERY REMOVAL/INSTALLATION

1. Battery removal Hold the handle tightly and push the battery latch to remove the battery. (See Fig. 1 and 2 ) CAUTION:

the main unit. The bit adapter cannot be attached to the special accessory anvil (square drive). (2) Before starting work with the adapter, tighten a few

Never short-circuit the battery. 2. Battery installation Insert the battery while observing its polarities. (See Fig. 2)

screws with it to make sure it’s tightening with the appropriate torque. (3) Tightening speed will be greatly reduced when driving

wood, tapping or other similar screws.

CHARGING

Before using the impact driver, charge the battery as follows. 1. Connect the charger’s power cord to a receptacle. When the power cord is connected, the charger’s pilot lamp will blink in red. (At 1-second intervals.) 2. Insert the battery into the charger. Insert the battery firmly, in the direction shown in Fig. 3, until it contacts the bottom of the charger compartment. CAUTION: If the battery is inserted in the reverse direction, not

Optional accessories are subject to change without notice.

APPLICATION

< WH12DM2, WH9DM2, WH12DMR > Driving and removing of small screws, small bolts,

only recharging will become impossible, but it may also cause problems in the charger such as deformed recharging terminal. 3. Charging When inserting a battery in the charger, charging will commence and the pilot lamp will light up continuously in red. When the battery becomes fully recharged, the pilot lamp will blink in red. (At 1-second intervals.) (See Table 5) (1) Pilot lamp indication

etc. < WR12DM2, WR9DM2 > Tightening and loosening of all types of bolts and

nuts, used for securing structural items

The indications of the pilot lamp will be as shown in Table 5, according to the condition of the charger or the rechargeable battery.

Indications of the lamps Before chargingBlinks Lights for 0.5 seconds. Does not light for (RED) 0.5 seconds. (off for 0.5 seconds) While chargingLights Lights continuously (RED) Charging completeBlinks Lights for 0.5 seconds. Does not light for (RED) 0.5 seconds. (off for 0.5 seconds) Charging impossibleFlikers Lights for 0.1 seconds. Does not light for (RED) 0.1 seconds. (off for 0.1 seconds)Malfunction in the battery or the charger Charging impossibleLights Lights continuously (GREEN)The battery temperature is high, making recharging impossible.

Table 5

Page 13 of the InFocus VR 9DM2 user manual — NOTE:
Pagina 13 · clicca per ingrandire
Pagina 13

(2) Regarding the temperatures of the rechargeable battery

used, the pilot lamp of the charger lights up green. In such a case, first let the battery cool, then start charging. When the pilot lamp flikers in red quickly (at 0.2-

The temperatures for rechargeable batteries are as shown in the table below, and batteries that have become hot should be cooled for a while before being recharged.

second intervals), check for and take out any foreign objects in the charger’s battery installation hole. If there are no foreign objects, it is probable that the battery or charger is malfunctioning. Take it to your Authorized Service Center. Since the built-in micro computer takes about 3

Table 6 Recharging ranges of batteries

Temperatures at Rechargeable batteries which the battery can be recharged

seconds to confirm that the battery being charged with UC14YFA is taken out, wait for a minimum of 3 seconds before reinserting it to continue charging. If the battery is reinserted within 3 seconds, the battery may not be properly charged.

EB1220BL, EB9B –5°C – 60°C

EB1226HL, EB1230HL, EB926H, EB930H 0°C – 45°C

(3) Regarding recharging time

Depending on the combination of the charger and batteries, the charging time will become as shown in Table 7.

PRIOR TO OPERATION

1. Preparing and checking the work environment Make sure that the work site meets all the conditions laid forth in the precautions. 2. Checking the battery Make sure that the battery is installed firmly. If it is at all loose it could come off and cause an accident. 3. Installing the bit (WH12DM2, WH9DM2, WH12DMR) Always follow the following procedure to install driver bit. (Fig. 4) (1) Pull the guide sleeve away from front of the tool. (2) Insert the bit into the hexagonal hole in the anvil. (3) Release the guide sleeve and it returns to its original

Table 7 Charging time (At 20°C)

EB1220BL, EB9B Approx. 50 min.

EB1226HL, EB926H Approx. 65 min.

EB1230HL, EB930H Approx. 70 min.

NOTE:

The charging time may vary according to the ambient temperature and power source voltage. 4. Disconnect the charger’s power cord from the receptacle. 5. Hold the charger firmly and pull out the battery. NOTE:

position. CAUTION:

If the guide sleeve does not return to its original position, then the bit is not installed properly. 4. Selecting the socket matched to the bolt (WR12DM2, WR9DM2) Be sure to use a socket which is matched to the bolt to be tightened. Using an improper socket will not only result in insufficient tightening but also in damage to the socket or nut. A worn or deformed hex. or square-holed socket will not give an adequate tightness for fitting to the nut or anvil, consequently resulting in loss of tightening torque. Pay attention to wear of socket hole, and replace before further wear has developed. Finally, install the socket prescribed in Item 5. The section on “Optional Accessories” details the relationship between bolt sizes and sockets. Sockets are named according to the dihedral width of the hexagonal hole. 5. Installing a socket (WR12DM2, WR9DM2) Select the socket to be used. Pin, O-ring type (Fig. 5 and 6) (1) Align the hole in the socket with the hole in the anvil

Be sure to pull out the battery from the charger after use, and then keep it.

Regarding electric discharge in case of new batteries, etc.

As the internal chemical substance of new batteries and batteries that have not been used for an extended period is not activated, the electric discharge might be low when using them the first and second time. This is a temporary phenomenon, and normal time required for recharging will be restored by recharging the batteries 2 – 3 times.

How to make the batteries perform longer

(1) Recharge the batteries before they become completely

exhausted. When you feel that the power of the tool becomes weaker, stop using the tool and recharge its battery. If you continue to use the tool and exhaust the electric current, the battery may be damaged and its life will become shorter. (2) Avoid recharging at high temperatures.

and insert the anvil into the socket. (2) Insert the pin into the socket. (3) Attach the ring to the groove on the socket. Plunger type (Fig. 7)

A rechargeable battery will be hot immediately after use. If such a battery is recharged immediately after use, its internal chemical substance will deteriorate, and the battery life will be shortened. Leave the battery and recharge it after it has cooled for a while. CAUTION: If the battery is charged while it is heated because it

Align the plunger located in the square part of the anvil with the hole in the hex. socket. Then push the plunger, and mount the hex. socket on the anvil. Check that the plunger is fully engaged in the hole. When removing the socket, reverse the sequence.

has been left for a long time in a location subject to direct sunlight or because the battery has just been

Charger · UC14YFA Battery

Page 14 of the InFocus VR 9DM2 user manual — HOW TO USE
Pagina 14 · clicca per ingrandire
Pagina 14

Retaining ring type (Fig. 8) (1) Align the square portions of the socket and the anvil

(4) Replacing the batteries

(a) Loosen the hook screw with a phillips-head

with each other. (2) Make sure to firmly install the socket by pushing it all

screwdriver (No. 1). (Fig. 14) Remove the hook cover by pushing in the direction of the arrow. (Fig. 15) (b) Remove the old batteries and insert the new

the way into the anvil. (3) When removing the socket, pull it out of the anvil.

batteries. Align with the hook indications and position the plus (+) and minus (–) terminals correctly. (Fig. 16) (c) Align the indentation in the hook main body with

listed in the operations manual and Hitachi’s catalog. Accidents or injuries could result from not doing so. Make sure to firmly install the socket in the anvil. If

the protuberance of the hook cover, press the hook cover in the direction opposite to that of the arrow shown in Fig. 15 and then tighten the screw. Use commercially available AAAA batteries (1.5 V). NOTE:

the socket is not firmly installed it might come out and cause injuries.

HOW TO USE

Do not tighten the screw excessively. Such action could strip the screw threads. CAUTION: Failure to observe the following can result in battery

leakage, rust or malfunction. Position the plus (+) and minus (–) terminals correctly. Replace both batteries at the same time. Do not mix old and new batteries. Remove exhausted batteries from the hook immediately. Do not discard batteries together with normal trash

main unit when carrying the tool main unit with the light equipped hook suspended from a waist belt. Injury may result if you carry the equipment suspended from the waist belt with sharp tipped components such as drill bit attached. 1. Using the light equipped hook The light equipped hook can be installed on the right or left side and the angle can be adjusted in 5 steps between 0° and 80°. (1) Operating the hook

and do not throw batteries into fire. Store batteries out of the reach of children. Use batteries correctly in accordance with the battery

specifications and indications. 2. Check the rotational direction The bit rotates clockwise (viewed from the rear side) by pushing the R-side of the push button. The L-side of the push button is pushed to turn the bit counterclockwise. (See Fig. 17) (The L and R marks are provided on the body.) CAUTION:

(a) Pull out the hook toward you in the direction of

arrow (A) and turn in the direction of arrow (B). (Fig. 9) (b) The angle can be adjusted in 5 steps (0°, 20°, 40°,

60°, 80°). Adjust the angle of the hook to the desired position for use. (2) Switching the hook position CAUTION:

The push button cannot be switched while the impact driver is turning. To switch the push button, stop the impact driver, then set the push button. 3. Switch operation When the trigger switch is depressed, the tool rotates.

Incomplete installation of the hook may result in bodily injury when used. (a) Securely hold the main unit and remove the screw

When the trigger is released, the tool stops. The rotational speed can be controlled by varying the

using a slotted head screwdriver or a coin. (Fig. 10) (b) Remove the hook and spring. (Fig. 11) (c) Install the hook and spring on the other side and

amount that the trigger switch is pulled. Speed is low when the trigger switch is pulled slightly and increases as the trigger switch is pulled more. 4. Tightening and loosening screws (WH12DM2, WH9DM2, WH12DMR) Install the bit that matches the screw, line up the bit in the grooves of the head of the screw, then tighten it. Push the impact driver just enough to keep the bit fitting the head of the screw. CAUTION:

securely fasten with screw. (Fig. 12) NOTE:

Pay attention to the spring orientation. Install the spring with larger diameter away from you. (Fig. 12) (3) Using as an auxiliary light

(a) Press the switch to turn off the light.

If forgotten, the light will turn off automatically after 15 minutes. (b) The direction of the light can be adjusted within

Applying the impact driver for too long tightens the screw too much and can break it. Tightening a screw with the impact driver at an angle to that screw can damage the head of the screw and the proper force will not be transmitted to the screw. Tighten with this impact driver lined up straight with the screw.

the range of hook positions 1 - 5. (Fig. 13) Lighting time

AAAA manganese batteriesapprox. 15 hrs. AAAA alkali batteries: approx. 30 hrs. CAUTION:

Do not look directly into the light. Such actions could result in eye injury.

Page 15 of the InFocus VR 9DM2 user manual — OPERATIONAL CAUTIONS
Pagina 15 · clicca per ingrandire
Pagina 15
5. Number of screws tightenings possible (WH12DM2, WH9DM2, WH12DMR) Please refer to the table below for the number of screw tightened possible with one charge.

the electronic circuit parts may overheat and be damaged. 3. Tightening torque Refer to Fig. 22, 23, 24, 25 and Fig. 26 for the tightening torque of bolts (according to size), under the conditions shown in Fig. 27. Please use this example as a general reference, as tightening torque will vary according to tightening conditions. NOTE: If a long striking time is used, screws will be strongly

WH12DM2, WH12DMR (EB1230HL)

No. of tightenings

WH12DM2 WH12DMR

Wood screw ø4 × 50 Approx. 790 Approx. 750 (Soft wood)

tightened. This may cause the screw to break, or may damage the tip of the bit. If the unit is held at an angle to the screw being

Machine screw M8 × 16 Approx. 1750 Approx. 1660

tightened, the head of the screw may be damaged, or the specified torque may not be transmitted to the screw. Always keep the unit and the screw being tightened in a straight line. 4. Use a tightening time suitable for the screw The appropriate torque for a screw differs according to the material and size of the screw, and the material being screwed etc., so please use a tightening time suitable for the screw. In particular, if a long tightening time is used in the case of screws smaller than M8, there is a danger of the screw breaking, so please confirm the tightening time and the tightening torque beforehand. 5. Work at a tightening torque suitable for the bolt under impact The optimum tightening torque for nuts or bolts differs with material and size of the nuts or bolts. An excessively large tightening torque for a small bolt may stretch or break the bolt. The tightening torque increases in proportion to the operaton time. Use the correct operating time for the bolt. 6. Holding the tool Hold the impact wrench firmly with both hands. In this case hold the wrench in line with the bolt. It is not necessary to push the wrench very hard. Hold the wrench with a force just sufficient to counteract the impact force. 7. Confirm the tightening torque The following factors contribute to a reduction of the tightening torque. So confirm the actual tightening torque needed by screwing up some bolts before the job with a hand torque wrench. Factors affecting the tightening torque are as follows. (1) Voltage

WH9DM2 (EB930H)

Screw used No. of tightenings

Wood screw ø4 × 50 Approx. 530 (Soft wood)

Machine screw M8 × 16 Approx. 1690

These values may vary slightly, according to surrounding temperature and battery characteristics. 6. Number of bolt tightened possible (WR12DM2, WR9DM2) Please refer to the table below for the number of bolt tightened possible with one charge.

WR12DM2 (EB1230HL)

Bolt used No. of tightenings

M12 Hightension bolt Approx. 180

WR9DM2 (EB930H)

Bolt used No. of tightenings

M12 Hightension bolt Approx. 120

These values may vary slightly, according to surrounding temperature and battery characteristics. NOTE:

The use of the battery EB1230HL, EB930H in a cold condition (below 0 degree Centigrade) can sometimes result in the weakened tightening torque and reduced amount of work. This, however, is a temporary phenomenon, and returns to normal when the battery warms up.

When the discharge margin is reached, voltage decreases and tightening torque is lowered. (2) Operating time

OPERATIONAL CAUTIONS

The tightening torque increases when the operating time increases. But the tightening torque does not increase above a certain value even if the tool is driven for a long time. (See Fig. 22, 23, 24, 25 and 26) (3) Diameter of bolt

1. Resting the unit after continuous work After use for continuous bolt-tightening work, rest the unit for 15 minutes or so when replacing the battery. The temperature of the motor, switch, etc., will rise if the work is started again immediately after battery replacement, eventually resulting in burnout. NOTE:

The tightening torque differs with the diameter of the bolt as shown in Fig. 22, 23, 24, 25 and 26. Generally a larger diameter bolt requires larger tightening torque. (4) Tightening conditions

Do not touch the protector, as it gets very hot during continuous work. 2. Cautions on use of the speed control switch This switch has a built-in, electronic circuit which steplessly varies the rotation speed. Consequently, when the switch trigger is pulled only slightly (low speed rotation) and the motor is stopped while continuously driving in screws, the components of

The tightening torque differs according to the torque ratio; class, and length of bolts even when bolts with the same size threads are used. The tightening torque also differs according to the condition of the surface of workpiece through which the bolts are to be tightened. When the bolt and nut turn together, torque is greatly reduced.

Screw used

Page 16 of the InFocus VR 9DM2 user manual — M12 × 45
Pagina 16 · clicca per ingrandire
Pagina 16

(5) Using optional parts (WR12DM2, WR9DM2)

(7) Tightening torque varies, depending on the battery’s

The tightening torque is reduced a little when an extension bar, universal joint or a long socket is used. (6) Clearance of the socket (WR12DM2, WR9DM2)

charge level. (WR12DM2, WR9DM2) Fig. 28 and 29 show examples of the relationship between tightening torque and the number of tightenings, for WR12DM2 and WR9DM2. As shown, tightening torque gradually weakens with the increase in the number of tightenings. In particular, as the torque decreases very close to the complete discharge (“a” margin in graph), the unit’s impact weakens, the number of time impacts declines and tightening torque drops off abruptly. If this occurs, check torque level, then recharge the battery if necessary.

A worn or deformed hex. or a square-holed socket will not give an adequate tightness to the fitting between the nut or anvil, consequently resulting in loss of tightening torque. Using an improper socket which does not match to the bolt will result in an insufficient tightening torque. Matching socket and bolt sizes are shown in Table 1, 2, 3 and 4.

M12 × 45

M14 × 50

M10 × 30 kgf·cm N·m

High tension bolt High tension bolt

0 0 1 2 3

0 1 2 3

0 1 2 3

Tightening timesec. (Steel plate thickness t = 10 mm)
Tightening timesec. (Steel plate thickness t = 25 mm)
Tightening timesec. (Steel plate thickness t = 25 mm)

M12 × 45 kgf·cm

M10 × 30 kgf·cm

M8 × 30 kgf·cm

High tension bolt High tension bolt

Ordinary bolt Ordinary bolt

0 0 1 2 3

0 0 1 2 3

00 1 2 3

Tightening timesec. (Steel plate thickness t = 10 mm)
Tightening timesec. (Steel plate thickness t = 25 mm)
Tightening timesec. (Steel plate thickness t = 25 mm)
Show 12 more labels / short text on this page
For WH12DM2 · kgf·cm N·m · kgf·cm N·m 1400 · High tension bolt · Ordinary bolt · Ordinary bolt · Ordinary bolt · For WH9DM2 · N·m · N·m · N·m · High tension bolt
Page 17 of the InFocus VR 9DM2 user manual — M12 × 45
Pagina 17 · clicca per ingrandire
Pagina 17

M12 × 45

M14 × 50

M10 × 30 kgf·cm N·m

0 0 1 2 3

0 1 2 3

0 1 2 3

Tightening timesec. (Steel plate thickness t = 10 mm)
Tightening timesec. (Steel plate thickness t = 25 mm)
Tightening timesec. (Steel plate thickness t = 25 mm)

M10 × 30 kgf·cm N·m

M12 × 45 kgf·cm N·m

M14 × 50 kgf·cm N·m

Ordinary bolt Ordinary bolt

0 0 1 2 3

0 0 1 2 3

0 0 1 2 3

Tightening timesec. (Steel plate thickness t = 10 mm)
Tightening timesec. (Steel plate thickness t = 25 mm)
Tightening timesec. (Steel plate thickness t = 25 mm)

M12 × 45 kgf·cm

M8 × 30 kgf·cm

M10 × 30 kgf·cm

00 1 2 3

0 0 1 2 3

0 0 1 2 3

Tightening timesec. (Steel plate thickness t = 10 mm)
Tightening timesec. (Steel plate thickness t = 10 mm)
Tightening timesec. (Steel plate thickness t = 25 mm)
Show 23 more labels / short text on this page
For WH12DMR · kgf·cm N·m · kgf·cm N·m 1400 · High tension bolt · High tension bolt · High tension bolt · Ordinary bolt · Ordinary bolt · Ordinary bolt · For WR12DM2 · High tension bolt · High tension bolt · High tension bolt · Ordinary bolt · For WR9DM2 · N·m · High tension bolt · N·m · N·m · High tension bolt · Ordinary bolt · Ordinary bolt · High tension bolt
Page 18 of the InFocus VR 9DM2 user manual — MAINTENANCE AND INSPECTION
Pagina 18 · clicca per ingrandire
Pagina 18
InFocus VR 9DM2 — ) ( diagram (page 18)
Fig. 18

*The following bolt is used. Ordinary bolt: Strength grade 4.8 High tensile bolt: Strength grade 12.9

Steel plate thickness t

) (

Explanation of strength grade: 4 — Yield point of bolt: 32 kgf/mm2 8 — Pulling strength of bolt: 40 kgf/mm2

M16 × 55 F10T (tighening time 3 sec) 2000

0 0 20 40 60 80 100 120 140

Number of tightenings (PCS)/charging

M14 × 50 High tension bolt

(tighening time 3 sec)

0 0 20 40 60 80 100 120 140 160

Number of tightenings (PCS)/charging

MAINTENANCE AND INSPECTION

3. Inspecting the mounting screws Regularly inspect all mounting screws and ensure that they are properly tightened. Should any of the screws be loose, retighten them immediately. Failure to do so may result in serious hazard. 4. Maintenance of the motor The motor unit winding is the very “heart” of the power tool. Exercise due care to ensure the winding does not become damaged and/or wet with oil or water.

1. Inspecting the driver bit (WH12DM2, WH9DM2, WH12DMR) Using a broken bit or one with a worn out tip is dangerous because the bit can slip. Replace it. 2. Inspecting the socket (WR12DM2, WR9DM2) A worn or deformed hex. or a square-holed socket will not give an adequate tightness to the fitting between the nut or anvil, consequently resulting in loss of tightening torque. Pay attention to wear of a socket holes periodically, and replace with a new one if needed.

Show 11 more labels / short text on this page
Bolt · Nut · For WR12DM2 · kgf·cm N·m · When full recharged · When completely discharged · For WR9DM2 · kgf·cm · N·m · When full recharged · When completely discharged
Page 19 of the InFocus VR 9DM2 user manual — ) (
Pagina 19 · clicca per ingrandire
Pagina 19
5. Inspecting the carbon brushes (Fig. 18) The motor employs carbon brushes which are consumable parts. Since and excessively worn carbon brush can result in motor trouble, replace the carbon brush with new ones when it becomes worn to or near the “wear limit”. In addition, always keep carbon brushes clean and ensure that they slide freely whthin the brush holders. NOTE:

When replacing the carbon brush with a new one, be sure to use the Hitachi Carbon Brush Code No. 999054. 6. Replacing carbon brushes Take out the carbon brush by first removing the brush cap and then hooking the protrusion of the carbon brush with a slotted head screw driver, etc., as shown in Fig. 20. When installing the carbon brush, choose the direction so that the nail of the carbon brush agrees with the contact portion outside the brush tube. Then push it in with a finger as illustrated in Fig. 21. Lastly, install the brush cap. CAUTION:

Blue: –Neutral Brown: –Live As the colours of the wires in the mains lead of this tool may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire coloured blue must be connected to the terminal marked with the letter N or coloured black. The wire coloured brown must be connected to the terminal marked with the letter L or coloured red. Neither core must be connected to the earth terminal. NOTE: This requirement is provided according to BRITISH STANDARD 2769: 1984. Therefore, the letter code and colour code may not be applicable to other markets except United Kingdom.

Be absolutely sure to insert the nail of the carbon brush into the contact portion outside the brush tube. (You can insert whichever one of the two nails provided.) Caution must be exercised since any error in this operation can result in the deformed nail of the carbon brush and may cause motor trouble at an early stage. 7 Cleaning of the outside When the impact driver is stained, wipe with a soft dry cloth or a cloth moistened with soapy water. Do not use chloric solvents, gasoline or paint thinner, as they melt plastics. 8. Storage Store the impact driver in a place in which the temperature is less than 40°C, and out of reach of children. 9. Service parts list A : Item No. B : Code No. C : No. Used D : Remarks CAUTION:

Information concerning airborne noise and vibration The measured values were determined according to EN50144. The typical A-weighted sound pressure level:

95 dB (A)(WH12DM2, WH12DMR) 95 dB (A)(WH9DM2) 96 dB (A)(WR12DM2) 96 dB (A)(WR9DM2) The typical A-weighted sound power level:

108 dB (A)(WH12DM2, WH12DMR) 108 dB (A)(WH9DM2) 109 dB (A)(WR12DM2) 109 dB (A)(WR9DM2) Wear ear protection.

The typical weighted root mean square acceleration value: 10.8 m/s2 (WH12DM2, WH12DMR) 9.7 m/s2 (WH9DM2) 12.1 m/s2 (WR12DM2) 10.9 m/s2 (WR9DM2)

Repair, modification and inspection of Hitachi Power Tools must be carried out by an Hitachi Authorized Service Center. This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance. In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed. MODIFICATIONS:

Hitachi Power Tools are constantly being improved and modified to incorporate the latest technological advancements. Accordingly, some parts (i.e. code numbers and/or design) may be changed without prior notice.

Fai una domanda su InFocus VR 9DM2

I possessori del prodotto e il nostro team di solito rispondono entro 24 ore, e la tua domanda sarà utile anche ad altri.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Nessuna domanda ancora per il dispositivo InFocus VR 9DM2

Invia la prima domanda: risponderanno altri possessori o il nostro team.

Documento originale

InFocus VR 9DM2 manuale in PDF

130 pagine·2.4 MB·Avvitatore a impulsi·PDF
Clicca su qualsiasi pagina in alto per aprirla qui
Pagina 1 / …
100%
Caricamento pagine…