


This page left blank intentionally

The signals listed on the following pages are used for initial setup, however the signal timings of some computer models may be different. In such a case, adjust V POSITION and H POSITION in the IMAGE menu.
Back porch (B) Front porch (D) Back porch (b) Front porch (d)
Data Data H. Sync. V. Sync.
Sync (A) Sync (a)
Active video (C) · Active video (c)

*1) Supported except for HDMI input. *2) Only supported on HDMI inputs.
Initial set signals

*1) Supported except for HDMI input. *2) Only supported on HDMI inputs.
Initial set signals





Connection to the ports (continued)




Connection to the ports (continued)


6 2 4 8 16 10 12 14 18
13 15 11 7 19 17 5 9 3
* HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
Ø3.5 stereo mini jack • 200 mVrms, 47kΩ terminator
Ø3.5 stereo mini jack

Connection to the ports (continued)


USB A type jack 4 3 2 1

D-sub 9pin plug • About the details of RS-232 communication, please refer to the section "RS-232 Communication".
RJ-45 jack 8 7 6 5 4 3 2 1

Pin Signal · 3 + Data · 4 Ground

Connection to the ports (continued)
To input SCART RGB signal; ex.

To input SCART RGB signal to the projector, use a SCART to RCA cable. Connect the plugs refer to above example. For more reference, please consult your dealer.

When the projector connects to the computer by RS-232 communication, the projector can be controlled with RS-232 commands from the computer. For details of RS-232 commands, refer to RS-232 Communication / Network command table (&16).
Connection 1. Turn off the projector and the computer.

of the projector RS-232 port of the computer
1 2 4 3
5 4 3 2 1
CD (1) (1) -- RD(2) (2) RD TD (3) (3) TD DTR (4) (4) -- GND (5) (5) GND DSR (6) (6) -- RTS (7) (7) RTS DTS (8) (8) CTS RI (9) (9) --
RS-232 Communication · RS-232C Cable (cross) · CONTROL port

Command Control via the Network
When the projector is connected to the network, the projector can be controlled with RS-232 commands from the computer with a web browser.
For RS-232 command information, refer to the RS-232 Communication / Network command table (&16).
Connection 1. Turn off the projector and the computer.
LAN cable (CAT-5 or greater)


Command Control via the Network (continued)
Communication Port The following port is assigned for command control.
Configure the following items from a web browser when command control is used.
Click the [Enable] check box to open [Network Control Port1 (Port: 23)] to use TCP #23. Default setting is “Enable”.
Click the [Enable] check box for the [Authentication] setting when authentication is required. Default setting is “Disable”.
When the authentication setting is enabled, the following settings are required.
Authentication Password Enter the desired authentication password. This setting will be the same for [Network Control Port1 (Port: 23)]. Default setting is blank. Re-enter Authentication Password
Port open · Authentication

Command Control via the Network (continued)
Communication Configuration Visit our website for additional RS-232 settings and information. To control this projector via RS-232, connect a null modem cable and set the control system serial port settings to match the following communication configuration:
RS-232 Port Settings Setting Value Bits per second 19,200 Data bits 8 Parity None Stop bits 1 Flow control None Emulation VT100
Command Format All commands consist of 3 alpha characters followed by a request, all enclosed in parentheses. The request can be a read request (indicated by a "?") or a write request (indicated by 1 to 4 ASCII digits).
(AAA?) where (starts the command AAA denotes the command ? denotes the read request ) ends the command A read command returns the range and the current setting, for example:
Read Command Examples Function Command Response Brightness (BRT?) (96-160, 128) Volume (VOL?) (0-32, 0) Lamp Hours (LMP?) (0-32766, 42)

Command Control via the Network (continued)
(AAA####) where (starts the command AAA denotes the command #### denotes the value to be written (leading zeros not necessary) ) ends the command
Some commands have ranges, while others are absolute. If a number greater than the maximum range is received, it is automatically set to the maximum number for that function. If a command is received that is not understood, a "?" is returned. With absolute settings, "0" is off, 1-9999 is on. The one exception is the Power command, where 0 is off and 1 is on.
To assure the projector can process a command, wait 3 seconds before entering the next command.
Read Command Examples Function Command Response Brightness (BRT140) Sets the brightness to 140 Power (PWR0) Turns power on Power (PWR1) Turns power off
Error Conditions Not all commands are supported for all projectors. If an unsupported command is issued, the command will be ignored. If a command is received that is not understood, a ‘?’ character will be returned indicating the command was not understood.
Limitations The projector cannot respond to commands coming in at a high-rate. Therefore, a delay must occur between commands to ensure that the command gets properly executed. To assure the projector can process a command, wait 3 seconds before entering the next command.
The Step column refers to increasing or decreasing the menu bar position since the On-screen Display is not an exact match of values. For example, Step 2 changes the data by 2 through the CLI (Command Line Interface). The menu bar is up (or down) by 1.

This projector is equipped with NETWORK BRIDGE function. When the projector connects to the computer by LAN communicaton, an external device that is connected with this projector by RS-232 communication can be controlled from the computer as a network terminal. For details, see the 6. Network Bridge function in the Network Guide.
Connection 1. Connect the computer's LAN port and the projector's LAN port with a LAN cable. 2. Connect the projector's CONTROL port and the RS-232 port of the devices that you want to control with a RS-232 cable. 3. Turn the computer on, and after the computer has started up, turn the projector on. 4. Set the COMMUNICATION TYPE to NETWORK BRIDGE. (&OPTION menu - SERVICE - COMMUNICATION in the User's Manual)


Network Bridge Communication

Communication settings For communication setting, use the OPTION - SERVICE - COMMUNICATION menu. (&OPTION menu - SERVICE - COMMUNICATION in the User's Manual)
BAUD RATE 4800bps / 9600bps / 19200bps / 38400bps
Data length 8 bit (fixed)
Start bit 1 bit (fixed)
Stop bit 1 bit (fixed)
Network Bridge Communication · Item Condition · Transmission method HALF-DUPLEX/FULL-DUPLEX

RS-232 Communication / Network command table
Function Command RW Min Max Default Step BASIC MENU Aspect Ratio 0: Auto 1: Native (IN5124 only) 2: 4:3 3: 16:9 6: 16:10
Horizontal Keystone DKH RW 38 218 128 1 Vertical Keystone DKV RW 38 218 128 1 Corner Correction Enable 0: Disable 1: Enable CNE RW 0 1 0
Corner Correction Top Left corner -H CN1 RW 0 511 (IN5122) 639 (IN5124) 0 1
Corner Correction Top Left corner -V CN2 RW 0 550 0 1
Corner Correction Top Right corner -H CN3 RW 0 511 (IN5122) 639 (IN5124) 0 1
Corner Correction Top Right corner -V CN4 RW 0 550 0 1
Corner Correction Bottom Left corner - H CN5 RW 0 511 (IN5122) 639 (IN5124) 0 1
Corner Correction Bottom Left corner - V CN6 RW 0 550 0 1
Corner Correction Bottom Right corner - H CN7 RW 0 511 (IN5122) 639 (IN5124) 0 1
Corner Correction Bottom Right corner - V CN8 RW 0 550 0 1
Corner Correction all corners reset 1: enable CNR RW 0 1 n/a
Side Correction Left Gain SC1 RW 98 158 128 1 Side Correction Right Gain SC2 RW 98 158 128 1
Side Correction V Position SC3 RW 0 768 (IN5122) 800 (IN5124) 384 (IN5124) 400 (IN5124) 1
Side Correction Top Gain SC4 RW 98 158 128 1 Side Correction Bottom Gain SC5 RW 98 158 128 1
Side Correction H Position SC6 RW 0 1024 (IN5122) 1280 (IN5124) 512 (IN5124) 640 (IN5124) 1

Function Command RW Min Max Default Step Presets 1: User 5: Presentation 7: Video 10: Bright 11: Whiteboard 12: Blackboard 13: Greenboard 15: Dynamic
5 (Computer in 1) 5 (Computer in 2) 5 (LAN) 5 (USB Type A) 5 (USB Type B) 15 (HDMI) 15 (Component) 15 (S-Video) 15 (Video) Low Power 0: Disable 1: Enable LPE RW 0 1 0
Language 0: English 1: French 2: German 3: Italian 5: Korean 6: Norwegian 7: Portuguese 8: Russian 9: Simplified Chinese 10: Spanish 11: Traditional Chinese 12: Swedish 13: Dutch 14: Polish 15: Turkish 16: Danish 17: Finnish
ADVANCED MENU: PICTURE Brightness BRT RW 96 160 128 1 Contrast CON RW 96 160 128 1

Function Command RW Min Max Default Step Gamma 32: 1 Default 16: 1 Custom 33: 2 Default 17: 2 Custom 34: 3 Default 18: 3 Custom 35: 4 Default 19: 4 Custom 36: 5 Default 20: 5 Custom 37: 6 Default 21: 6 Custom
32 (Computer in 1) 32 (Computer in 2) 32 (LAN) 32 (USB Type A) 32 (USB Type B) 34 (HDMI) 34 (Component) 34 (S-Video) 34 (Video)
Gamma Custom-1 Point 1 G11 RW 112 144 128 1 Gamma Custom-1 Point 2 G12 RW 112 144 128 1 Gamma Custom-1 Point 3 G13 RW 112 144 128 1 Gamma Custom-1 Point 4 G14 RW 112 144 128 1 Gamma Custom-1 Point 5 G15 RW 112 144 128 1 Gamma Custom-1 Point 6 G16 RW 112 144 128 1 Gamma Custom-1 Point 7 G17 RW 112 144 128 1 Gamma Custom-1 Point 8 G18 RW 112 144 128 1 Gamma Custom-2 Point 1 G19 RW 112 144 128 1 Gamma Custom-2 Point 2 G20 RW 112 144 128 1 Gamma Custom-2 Point 3 G21 RW 112 144 128 1 Gamma Custom-2 Point 4 G22 RW 112 144 128 1 Gamma Custom-2 Point 5 G23 RW 112 144 128 1 Gamma Custom-2 Point 6 G24 RW 112 144 128 1 Gamma Custom-2 Point 7 G25 RW 112 144 128 1 Gamma Custom-2 Point 8 G26 RW 112 144 128 1 Gamma Custom-3 Point 1 G27 RW 112 144 128 1 Gamma Custom-3 Point 2 G28 RW 112 144 128 1 Gamma Custom-3 Point 3 G29 RW 112 144 128 1 Gamma Custom-3 Point 4 G30 RW 112 144 128 1 Gamma Custom-3 Point 5 G31 RW 112 144 128 1 Gamma Custom-3 Point 6 G32 RW 112 144 128 1 Gamma Custom-3 Point 7 G33 RW 112 144 128 1 Gamma Custom-3 Point 8 G34 RW 112 144 128 1 Gamma Custom-4 Point 1 G35 RW 112 144 128 1 Gamma Custom-4 Point 2 G36 RW 112 144 128 1 Gamma Custom-4 Point 3 G37 RW 112 144 128 1 Gamma Custom-4 Point 4 G38 RW 112 144 128 1 Gamma Custom-4 Point 5 G39 RW 112 144 128 1 Gamma Custom-4 Point 6 G40 RW 112 144 128 1

Function Command RW Min Max Default Step Gamma Custom-4 Point 7 G41 RW 112 144 128 1 Gamma Custom-4 Point 8 G42 RW 112 144 128 1 Gamma Custom-5 Point 1 G43 RW 112 144 128 1 Gamma Custom-5 Point 2 G44 RW 112 144 128 1 Gamma Custom-5 Point 3 G45 RW 112 144 128 1 Gamma Custom-5 Point 4 G46 RW 112 144 128 1 Gamma Custom-5 Point 5 G47 RW 112 144 128 1 Gamma Custom-5 Point 6 G48 RW 112 144 128 1 Gamma Custom-5 Point 7 G49 RW 112 144 128 1 Gamma Custom-5 Point 8 G50 RW 112 144 128 1 Gamma Custom-6 Point 1 G51 RW 112 144 128 1 Gamma Custom-6 Point 2 G52 RW 112 144 128 1 Gamma Custom-6 Point 3 G53 RW 112 144 128 1 Gamma Custom-6 Point 4 G54 RW 112 144 128 1 Gamma Custom-6 Point 5 G55 RW 112 144 128 1 Gamma Custom-6 Point 6 G56 RW 112 144 128 1 Gamma Custom-6 Point 7 G57 RW 112 144 128 1 Gamma Custom-6 Point 8 G58 RW 112 144 128 1 Color Temperature 0: 1 High 1: 1 Custom 2: 2 Mid 3: 2 Custom 4: 3 Low 5: 3 Custom 6: 4 Hi-Bright-1 7: 4 Custom 8: 5 Hi-Bright-2 9: 5 Custom 10: 6 Hi-Bright-3 11: 6 Custom
2 (Computer in 1) 2 (Computer in 2) 2 (LAN) 2 (USB Type A) 2 (USB Type B) 0 (HDMI) 0 (Component) 0 (S-Video) 0 (Video)
Color Temperature - 1 Red Gain RG1 RW 96 160 128 1 Color Temperature - 2 Red Gain RG2 RW 96 160 128 1 Color Temperature - 3 Red Gain RG3 RW 96 160 128 1 Color Temperature - 4 Red Gain RG4 RW 96 160 128 1 Color Temperature - 5 Red Gain RG5 RW 96 160 128 1 Color Temperature - 6 Red Gain RG6 RW 96 160 128 1 Color Temperature - 1 Green Gain GG1 RW 96 160 128 1 Color Temperature - 2 Green Gain GG2 RW 96 160 128 1 Color Temperature - 3 Green Gain GG3 RW 96 160 128 1 Color Temperature - 4 Green Gain GG4 RW 96 160 128 1 Color Temperature - 5 Green Gain GG5 RW 96 160 128 1 Color Temperature - 6 Green Gain GG6 RW 96 160 128 1 Color Temperature - 1 Blue Gain BG1 RW 96 160 128 1 Color Temperature - 2 Blue Gain BG2 RW 96 160 128 1 Color Temperature - 3 Blue Gain BG3 RW 96 160 128 1 Color Temperature - 4 Blue Gain BG4 RW 96 160 128 1 Color Temperature - 5 Blue Gain BG5 RW 96 160 128 1

Function Command RW Min Max Default Step Color Temperature - 6 Blue Gain BG6 RW 96 160 128 1 Color Temperature - 1 Red Offset RF1 RW 96 160 128 1 Color Temperature - 2 Red Offset RF2 RW 96 160 128 1 Color Temperature - 3 Red Offset RF3 RW 96 160 128 1 Color Temperature - 4 Red Offset RF4 RW 96 160 128 1 Color Temperature - 5 Red Offset RF5 RW 96 160 128 1 Color Temperature - 6 Red Offset RF6 RW 96 160 128 1 Color Temperature - 1 Green Offset GF1 RW 96 160 128 1 Color Temperature - 2 Green Offset GF2 RW 96 160 128 1 Color Temperature - 3 Green Offset GF3 RW 96 160 128 1 Color Temperature - 4 Green Offset GF4 RW 96 160 128 1 Color Temperature - 5 Green Offset GF5 RW 96 160 128 1 Color Temperature - 6 Green Offset GF6 RW 96 160 128 1 Color Temperature - 1 Blue Offset BF1 RW 96 160 128 1 Color Temperature - 2 Blue Offset BF2 RW 96 160 128 1 Color Temperature - 3 Blue Offset BF3 RW 96 160 128 1 Color Temperature - 4 Blue Offset BF4 RW 96 160 128 1 Color Temperature - 5 Blue Offset BF5 RW 96 160 128 1 Color Temperature - 6 Blue Offset BF6 RW 96 160 128 1 Color CLR RW 96 160 128 1 Tint TNT RW 96 160 128 1 Sharpness SHP RW 125 131 128 1
1 1 (Computer in 1) 1 (Computer in 2) 1 (LAN) 1 (USB Type A) 1 (USB Type B) 2 (HDMI) 2 (Component) 2 (S-Video) 2 (Video) User Preset 1 0: Load 1: Save
US1 W 0 1 n/a
US2 W 0 1 n/a
US3 W 0 1 n/a
US4 W 0 1 n/a


Function Command RW Min Max Default Step ADVANCED MENU: IMAGE Aspect Ratio 0: Auto 1: Native (IN5124 Only) 2: 4:3 3: 16:9 6: 16:10
Horizontal Position HPS RW Def:- 128 Def:+128 auto 1
1 (HDMI) 2 (Video/ S-Video) 2 (Component) Color Space 0: RGB 1: REC709 2: REC601 3: RGB Video 4: Auto

Function Command RW Min Max Default Step S-Video Standard 0: Auto 1: NTSC 2: PAL 3: SECAM 4: NTSC4.43 5: M-PAL 6: N-PAL
Horizontal Keystone DKH RW 38 218 128 1 Vertical Keystone DKV RW 38 218 128 1 Corner Correction Enable 0: Disable 1: Enable
Corner Correction Top Left corner -H CN1 RW 0 511 (IN5122) 639 (IN5124) 0 1
Corner Correction Top Left corner -V CN2 RW 0 550 0 1
Corner Correction Top Right corner -H CN3 RW 0 511 (IN5122) 639 (IN5124) 0 1
Corner Correction Top Right corner -V CN4 RW 0 550 0 1
Corner Correction Bottom Left corner -H CN5 RW 0 511 (IN5122) 639 (IN5124) 0 1
Corner Correction Bottom Left corner -V CN6 RW 0 550 0 1
Corner Correction Bottom Right corner -H CN7 RW 0 511 (IN5122) 639 (IN5124) 0 1
Corner Correction Bottom Right corner -V CN8 RW 0 550 0 1

Function Command RW Min Max Default Step Corner Correction all corners Reset 0: n/a 1: enable
CNR RW 0 1 n/a
Side Correction Left Gain SC1 RW 98 158 128 1 Side Correction Right Gain SC2 RW 98 158 128 1
Side Correction V Position SC3 RW 0 768 (IN5122) 800 (IN5124) 384(IN5124) 400(IN5124) 1
Side Correction Top Gain SC4 RW 98 158 128 1 Side Correction Bottom Gain SC5 RW 98 158 128 1
Side Correction H Position SC6 RW 0 1024 (IN5122) 1280 (IN5124) 512(IN5124) 640(IN5124) 1
SCR W 0 1 n/a
Monitor Out for Source 0 (Computer in 1) 1: Computer in 1 255: Off
Monitor Out for Source 1 (Computer in 2) 2: Computer in 2 255: Off
Monitor Out for Source 2 (LAN) 1: Computer in 1 2: Computer in 2 255: Off
Monitor Out for Source 3 (USB Type A) 1: Computer in 1 2: Computer in 2 255: Off
Monitor Out for Source 4 (USB Type B) 1: Computer in 1 2: Computer in 2 255: Off

Function Command RW Min Max Default Step Monitor Out for Source 5 (HDMI) 1: Computer in 1 2: Computer in 2 255: Off
Monitor Out for Source 6 (Component) 1: Computer in 1 2: Computer in 2 255: Off
Monitor Out for Source 7 (S-Video) 1: Computer in 1 2: Computer in 2 255: Off
Monitor Out for Source 8 (Video) 1: Computer in 1 2: Computer in 2 255: Off
Volume for Source 1 (Computer in 2) VL1 RW 0 48 24 1
Volume for Source 2 (LAN) VL2 RW 0 48 24 1
Volume for Source 3 (USB Type A) VL3 RW 0 48 24 1
Volume for Source 4 (USB Type B) VL4 RW 0 48 24 1
Volume for Source 5 (HDMI) VL5 RW 0 48 24 1
Volume for Source 6 (Component) VL6 RW 0 48 24 1
Volume for Source 7 (S-Video) VL7 RW 0 48 24 1
Volume for Source 8 (Video) VL8 RW 0 48 24 1
Volume for Standby VLS RW 0 48 24 1 Internal Speakers 0: Disable 1: Enable

Function Command RW Min Max Default Step Audio for Source 0 (Computer in 1) 0: Audio 1 1: Audio 2 2: Audio 3 5: Mute
Audio for Source 1 (Computer in 2) 0: Audio 1 1: Audio 2 2: Audio 3 5: Mute
Audio for Source 2 (LAN) 0: Audio 1 1: Audio 2 2: Audio 3 5: Mute
Audio for Source 3 (USB Type A) 0: Audio 1 1: Audio 2 2: Audio 3 5: Mute
Audio for Source 4 (USB Type B) 0: Audio 1 1: Audio 2 2: Audio 3 5: Mute
Audio for Source 5 (HDMI) 0: Audio 1 1: Audio 2 2: Audio 3 4: HDMI Audio 5: Mute
Audio for Source 6 (Component) 0: Audio 1 1: Audio 2 2: Audio 3 5: Mute
Audio for Source 7 (S-Video) 0: Audio 1 1: Audio 2 2: Audio 3 5: Mute
Audio for Source 8 (Video) 0: Audio 1 1: Audio 2 2: Audio 3 5: Mute


Function Command RW Min Max Default Step HDMI Noise Cancel 0: Disable 1: Enable
Menu Positon H OFH RW 0 10 0 (left) 1 Menu Positon V OFV RW 0 10 10 (top) 1 Blank Screen 0: Blue 3: Black 4: white 5: Factory Logo 6: SnapShot
Ruled Lines 0: Lines on White 1: Lines on Black 2: Grids on White 3: Grids on Black 4: Circle on White 5: Circle on Black 6: Map 1 7: Map 2 8: Stack 9: Test Pattern

Function Command RW Min Max Default Step
Custom Key (Effect) 0: Blank 1: Mute 2: Aspect Ratio 3: Source 4: Auto Image 5: Freeze 6: Magnify 7: Source Info 8: Service Info 15: AV Mute 18: Ruled Lines 19: Slideshow 20: MyImage 21: Messenger 22: Auto Keystone 23: Active Iris 24: Re
Source 1 0: Computer in 1 1: Computer in 2 2: LAN 3: USB Type A 4: USB Type B 5: HDMI 6: Component 7: S-Video 8: Video
Source 2 0: Computer in 1 1: Computer in 2 2: LAN 3: USB Type A 4: USB Type B 5: HDMI 6: Component 7: S-Video 8: Video
Source 3 0: Computer in 1 1: Computer in 2 2: LAN 3: USB Type A 4: USB Type B 5: HDMI 6: Component 7: S-Video 8: Video

Function Command RW Min Max Default Step
Source 4 0: Computer in 1 1: Computer in 2 2: LAN 3: USB Type A 4: USB Type B 5: HDMI 6: Component 7: S-Video 8: Video
Power-up Source 0: Computer in 1 1: Computer in 2 2: LAN 3: USB Type A 4: USB Type B 5: HDMI 6: Component 7: S-Video 8: Video
Ghost Red GSR RW 118 138 128 1 Ghost Green GSG RW 118 138 128 1 Ghost Blue GSB RW 118 138 128 1 Reset Lamp Hours 1: reset LRT W 0 1 n/a
Key Lock - Control Panel 0: Disable 1: Enable
RST W 0 1 n/a
ADVANCED MENU: NETWORK IP Address (1st octet) IP1 R 0 255 192 IP Address (2nd octet) IP2 R 0 255 168 IP Address (3rd octet) IP3 R 0 255 1 IP Address (4th octet) IP4 R 0 255 254

Function Command RW Min Max Default Step My Image Display 0: Off 1: Image-1 2: Image-2 3: Image-3 4: Image-4
Magnify MAG RW 0 48 8 1 Magnify Enable 0: Disable 1: Enable
Magnify Position Horizontal MPH RW 0 6 0 1 Magnify Position Vertical MPV RW 0 6 0 1 Mute 0: Disable 1: Enable
Source 0: Computer in 1 1: Computer in 2 2: LAN 3: USB Type A 4: USB Type B 5: HDMI 6: Component 7: S-Video 8: Video

Function Command RW Min Max Default Step Freeze 0: Off 1: On
INFOCUS UNIQUE About (Source Info) 0: n/a 1: enable
ABT W 0 1 n/a
Number of Lamp Resets LMR R 0 32766 0 Lamp Total On Time (All Bulbs) LMT R 0 2147483646 0 Time In Hours Last Bulb1 Lasted LB1 R 0 32766 0
Time In Hours Last Bulb2 Lasted LB2 R 0 32766 0
Time In Hours Last Bulb3 Lasted LB3 R 0 32766 0
Lamp Hours LMP R 0 32766 0 Filter Hours FLT R 0 32766 0 Unit Total Time On ONL R 0 2147483646 0 Error Status 0: No Error 1: Lamp won't strike 2: reserved 3: Lamp unexpectedly goes out 4: Fan failure 5: Over Temp Condition 6: reserved 7: Lamp Cover Error 8: Overheating alarm 9: Lamp Time Over 10: Temp Sensor out 11: Filter Time Over 12: Unidentifiable Error (system failure)


POWR Power Control 0 = Standby 1 = Power On
0 = Standby 1 = Power On 2 = Cool Down
11 = COMPUTER IN 1 12 = COMPUTER IN 2 21 = COMPONENT 22 = S-VIDEO 23 = VIDEO 31 = HDMI 41 = USB TYPE A 51 = LAN 52 = USB TYPE B
11 = COMPUTER IN 1 12 = COMPUTER IN 2 21 = COMPONENT 22 = S-VIDEO 23 = VIDEO 31 = HDMI 41 = USB TYPE A 51 = LAN 52 = USB TYPE B
10 = BLANK off 11 = BLANK on 20 = Mute off 21 = Mute on 30 = AV Mute off 31 = AV Mute on
10 = BLANK off 11 = BLANK on 20 = Mute off 21 = Mute on 30 = AV Mute off 31 = AV Mute on

Commands Control Description Parameter or Response
3rd byte: Refers to Temperature error; one of 0 to 2 4th byte: Refers to Cover error; one of 0 to 2 5th byte: Refers to Filter error; one of 0 to 2 6th byte: Refers to Other error; one of 0 to 2
ERST ? Error Status inquiry
The mearning of 0 to 2 is as given below 0 = Error is not detected; 1 = Warning; 2 = Error
LAMP ? Lamp Status inquiry 1st number (digits 1 to 5): Lamp Time 2nd number : 0 = Lamp off, 1 = Lamp on INST ? Input Source List inquiry 11 12 21 22 23 31 41 51 52
NAME ? Projector Name inquiry Responds with the name set in "PROJECTOR NAME" of "NETWORK"
INF1 ? Manufucturer's Name
INF2 ? Model Name inquiry Your model name, "IN5122", or "IN5124"
INFO ? Other Information inquiry Responds with the factory information and so on CLSS ? Class Information inquiry 1
inquiry INFOCUS
I possessori del prodotto e il nostro team di solito rispondono entro 24 ore, e la tua domanda sarà utile anche ad altri.
Invia la prima domanda: risponderanno altri possessori o il nostro team.