IT
InFocus logo
Manuale d'uso ufficiale

InFocus DS 12DM

78 pagine·1.2 MB·Trapano a batteria·PDF·ENJA
InFocus DS 12DM
Indice dei contenuti 10 sezioni GENERAL OPERATIONAL PRECAUTIONS · PRECAUTIONS FOR CORDLESS DRIVER DRILL · SPECIFICATIONS · POWER TOOL · … MostraNascondi
Page 1 of the InFocus DS 12DM user manual — PRECAUTIONS FOR CORDLESS DRIVER DRILL
Pagina 1 · clicca per ingrandire
Pagina 1

GENERAL OPERATIONAL PRECAUTIONS

22. Always use the charger at the voltage specified on the nameplate. 23. Do not touch movable parts or accessories unless the battery has been removed. 24. Always charge the battery before use. 25. Never use a battery other than that specified. Do not connect a usual dry cell, a rechargeable battery other than that specified or a car battery to the power tool. 26. Do not use any transformer that has a booster. 27. Do not charge the battery from an engine electric generator or DC power supply. 28. Always charge indoors. Because the charger and battery heat slightly during charging, charge the battery in a place not exposed to direct sunlight; where the humidity is low and the ventilation is good. 29. When working in a high place, pay attention to the activities below to make sure there are no people below. 30. Use the exploded assembly drawing on this handling instructions only for authorized servicing. 31. If the supply cord is damaged, it must be replaced by the manufacture or its service agent or a similarly qualified person in order to avoid a hazard.

1. Keep work area clean. Cluttered areas and benches invite accidents. 2. Avoid dangerous environment. Don’t expose power tools and charger to rain. Don’t use power tools and charger in damp or wet locations. And keep work area well lit. Never use power tools and charger near flammable or explosive materials. Do not use tool and charger in presence of flammable liquids or gases. 3. The appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure that they do not play with the appliance. All visitors should be kept safe distance from work area. 4. Store idle tools and charger. When not in use, tools and charger should be stored in dry, high or locked- up place – out of reach of the children and infirm persons. Store tools and charger in a place where the temperature is less than 40°C. 5. Don’t force tool. It will do the job better and safer at the rate for which it was designed. 6. Use right tool. Don’t force small tool or attachment to do the job of a heavy duty tool. 7. Wear proper apparel. Do not wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves and non-skid footwears are recommended when working outdoor. 8. Use eye protection with most tools. Also use face or dust mask if cutting operation is dusty. 9. Don’t abuse cord. Never carry charger by cord or yank it to disconnect from receptacle. Keep cord from heat, oil and sharp edges. 10. Secure work. Use clamps or a vise to hold work. It’s safer than using your hand and it frees both hands to operate tool. 11. Don’t overreach. Keep proper footing and balance at all times. 12. Maintain tools with care. Keep tools sharp at all times, and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 13. When the charger is not in use, or when being maintained and inspected, disconnect its power cord from the receptacle. 14. Remove chuck wrenches and wrenches. Form habit of checking to see that wrenches are removed from tool before turning it on. 15. Avoid accidental starting. Don’t carry tool with finger on switch. 16. To avoid danger, always use only the specified charger. 17. Use only genuine HITACHI replacement parts. 18. Do not use power tools for applications other than those specified in the Handling Instructions. 19. To avoid personal injury, use only the accessories or attachment recommended in these handling instructions or in the HITACHI catalog. 20. If the supply cord of this charger is damaged, the charger must be returned to the HITACHI authorized service center for the cord to be replaced. Let only the authorized service center do the repairing. The Manufacturer will not be responsible for any damages or injuries caused by repair by the unauthorized persons or by mishandling of the tool. 21. To ensure the designed operational integrity of power tools and charger, do not remove installed covers or screws.

PRECAUTIONS FOR CORDLESS DRIVER DRILL

1. Always charge the battery at a temperature of 10 – 40°C. A temperature of less than 10°C will result in over charging which is dangerous. The battery cannot be charged at a temperature higher than 40°C. The most suitable temperature for charging is that of 20 – 25°C. 2. When one charging is completed, leave the charger for about 15 minutes before the next charging of battery. Do not charge more than two batteries consecutively. 3. Do not allow foreign matter to enter the hole for connecting the rechargeable battery. 4. Never disassemble the rechargeable battery and charger. 5. Never short-circuit the rechargeable battery. Short- circuiting the battery will cause a great electric current and overheat. It results in burn or damage to the battery. 6. Do not dispose of the battery in fire. If the battery is burnt, it may explode. 7. When drilling in wall, floor or ceiling, check for buried electric power cord, etc. 8. Bring the battery to the shop from which it was purchased as soon as the post-charging battery life becomes too short for practical use. Do not dispose of the exhausted battery. 9. Using an exhausted battery will damage the charger. 10. Do not insert object into the air ventilation slots of the charger. Inserting metal objects or inflammables into the charger air ventilation slots will result in electrical shock hazard or damaged charger. 11. When mounting a bit into the keyless chuck, tighten the sleeve adequately. If the sleeve is not tight, the bit may slip or fall out, causing injury.

Page 2 of the InFocus DS 12DM user manual — CHARGING
Pagina 2 · clicca per ingrandire
Pagina 2

SPECIFICATIONS

POWER TOOL

ModelDS9DMDS12DM No-load speed (Low/High)0 – 330 / 0 – 1150 min–10 – 350 / 0 – 1200 min–1 CapacityWoo (Thick Drilling Meta (Thickd ness 18 mm)21 mm27 mm l ness 1.6 mmSteel: 10 mm, ) Aluminum: 10 mmSteel: 13 mm, Aluminum: 13 mm Mac Driving Woohine screw6 mm6 mm d screw6.2 mm (diameter) × 56 mm (length) (Requires a pilot hole)6.8 mm (diameter) × 50 mm (length) (Requires a pilot hole) Rechargeable batteryEB9B : Ni-Cd 9.6 V (2.0 Ah, 8 cells) EB926H : Ni-MH 9.6 V (2.6 Ah, 8 cells) EB930H : Ni-MH 9.6 V (3.0 Ah, 8 cells)EB1220BL : Ni-Cd 12 V (2.0 Ah, 10 cells) EB1226HL : Ni-MH 12 V (2.6 Ah, 10 cells) EB1230HL : Ni-MH 12 V (3.0 Ah, 10 cells) Weight1.5 kg1.7 kg
CHARGER APPLICATIONS Model UC14YFA UC18YG Driving and removing of machine screws, wood Charging voltage 7.2 – 14.4 V 7.2 – 18 V screws, tapping screws, etc. Weight 0.6 kg 0.3 kg Drilling of various metals. Drilling of various woods. STANDARD ACCESSORIES BATTERY REMOVAL/INSTALLATION 1 Plus driver bit (No. 2) 1 1. Battery removal DS9DM 2 Charger (UC14YFA or UC18YG) 1 Hold the handle tightly and push the battery latch DS12DM to remove the battery (See Figs. 1 and 2). 3 Plastic case 1 CAUTION DS9DM DS12DM1 Plus driver bit (No. 2) 1 2 Charger (UC14YFA or UC18YG) 1 3 Plastic case 1
Model UC14YFAUC18YG Charging voltage 7.2– 14.4 V7.2 – 18 V Weight 0.6 kg0.3 kg

Standard accessories are subject to change without notice.

Never short-circuit the battery. 2. Battery installation Insert the battery while observing its polarities (See Fig. 2).

OPTIONAL ACCESSORIES (sold separately)

1. Battery (EB914, EB9B, EB9H, EB926H, EB930H) (For DS9DM)

CHARGING

〈UC14YFA〉 Before using the driver drill, charge the battery as follows. 1. Connect the charger’s power cord to a receptacle When the power cord is connected, the charger’s pilot lamp will blink in red (At 1-second intervals). 2. Insert the battery into the charger Firmly insert the battery into the charger till it contacts the bottom of the charger and checking the polarities as shown in Fig. 3. CAUTION

2. Battery (EB1214L, EB1220BL, EB1222HL, EB1226HL, EB1230HL) (For DS12DM)

If the batteries are inserted in the reverse direction, not only recharging will become impossible, but it may also cause problems in the charger such as a deformed recharging terminal. 3. Charging When inserting a battery in the charger, charging will commence and the pilot lamp will light continuously in red. When the battery becomes fully recharged, the pilot lamp will blink in red (At 1-second intervals.) (See Table 1). (1) Pilot lamp indication

The indications of the pilot lamp will be as shown in Table 1, according to the condition of the charger or the rechargeable battery.

Optional accessories are subject to change without notice.

Page 3 of the InFocus DS 12DM user manual — NOTE
Pagina 3 · clicca per ingrandire
Pagina 3
Indications of the pilot lamp Before chargingLights for 0.5 seconds. Does not light for 0.5 Blinks seconds. (off for 0.5 seconds) (RED) While chargingLights Lights continuously (RED) Charging completeLights for 0.5 seconds. Does not light for 0.5 Blinks seconds. (off for 0.5 seconds) (RED) Charging impossibleLights for 0.1 seconds. Does not light for 0.1 Flickers seconds. (off for 0.1 seconds) (RED)Malfunction in the battery or the charger. Charging impossibleLights Lights continuously (GREEN)The battery temperature is high, making recharging impossible.

(2) Regarding the temperatures of the rechargeable

NOTE

battery The temperatures for rechargeable batteries are as shown in the table below, and batteries that have become hot should be cooled for a while before being recharged.

After operation, pull out batteries from the charger first, and then keep the batteries properly.

Regarding electric discharge in case of new batteries, etc.

As the internal chemical substance of new batteries and batteries that have not been used for an extended period is not activated, the electric discharge might be low when using them the first and second time. This is a temporary phenomenon, and normal time required for recharging will be restored by recharging the batteries 2 – 3 times.

Table 2 Recharging ranges of batteries

Rechargeable batteriesTemperatures at which the battery can be recharged EB912S, EB914S, EB914, EB9B, EB1212S, EB1214S, EB1214L, EB1220BL–5°C – 60°C EB9H, EB926H, EB930H, EB1222HL, EB1226HL, EB1230HL0°C – 45°C

How to make the batteries perform longer.

(1) Recharge the batteries before they become

completely exhausted. When you feel that the power of the tool becomes weaker, stop using the tool and recharge its battery. If you continue to use the tool and exhaust the electric current, the battery may be damaged and its life will become shorter. (2) Avoid recharging at high temperatures.

(3) Regarding recharging time

Depending on the combination of the charger and batteries, the charging time will become as shown in Table 3.

Table 3 Charging time (At 20°C)

A rechargeable battery will be hot immediately after use. If such a battery is recharged immediately after use, its internal chemical substance will deteriorate, and the battery life will be shortened. Leave the battery and recharge it after it has cooled for a while. CAUTION If the battery is charged while it is heated because

Charger BatteryUC14YFA EB912S, EB914S, EB914, EB1212S, EB1214S, EB1214LApprox. 30 min. EB9B, EB1220BLApprox. 50 min. EB9H, EB1222HLApprox. 55 min. EB926H, EB1226HLApprox. 60 min. EB930H, EB1230HLApprox. 70 min.

it has been left for a long time in a location subject to direct sunlight or because the batetery has just been used, the pilot lamp of the charger lights up green. In such a case, first let the battery cool, then start charging. When the pilot lamp flickers in red (at 0.2-second

NOTE

The charging time may vary according to temperature and power source voltage. 4. Disconnect the charger’s power cord from the receptacle 5. Hold the charger firmly and pull out the battery

intervals), check for and take out any foreign objects in the charger’s battery installation hole. If there are no foreign objects, it is probable that the battery or charger is malfunctioning. Take it to your authorized Service Center.

Table 1

Page 4 of the InFocus DS 12DM user manual — HOW TO USE
Pagina 4 · clicca per ingrandire
Pagina 4

Since the built-in micro computer takes about 3

Regarding electric discharge in case of new batteries, etc.

seconds to confirm that the battery being charged with UC14YFA is taken out, wait for a minimum of 3 seconds before reinserting it to continue charging. If the battery is reinserted within 3 seconds, the battery may not be properly charged. 〈UC18YG〉 Before using the driver drill, charge the battery as follows. 1. Connect the charger power cord to the receptacle Connecting the power cord will turn on the charger. 2. Insert the battery into the charger Insert the battery firmly while observing its direction, until it contacts the bottom of the charger (the pilot lamp lights up) (See Fig. 4). CAUTION

As the internal chemical substance of new batteries and batteries that have not been used for an extended period is not activated, the electric discharge might be low when using them the first and second time. This is a temporary phenomenon, and normal time required for recharging will be restored by recharging the batteries 2 – 3 times.

How to make the batteries perform longer.

(1) Recharge the batteries before they become completely

exhausted. When you feel that the power of the tool becomes weaker, stop using the tool and recharge its battery. If you continue to use the tool and exhaust the electric current, the battery may be damaged and its life will become shorter. (2) Avoid recharging at high temperatures.

If the pilot lamp does not light up, pull out the power cord from the receptacle and check the battery mounting condition. (1) Regarding the temperatures of the rechargeable

battery The temperatures for rechargeable batteries are as shown in Table 4.

A rechargeable battery will be hot immediately after use. If such a battery is recharged immediately after use, its internal chemical substance will deteriorate, and the battery life will be shortened. Leave the battery and recharge it after it has cooled for a while.

Table 4 Recharging ranges of batteries

Rechargeable batteriesTemperatures at which the battery can be recharged EB912S, EB914S, EB914, EB9B, EB1212S, EB1214S, EB1214L, EB1220BL0°C – 45°C

PRIOR TO OPERATION

1. Setting up and checking the work environment Check if the work environment is suitable by following the precautions.

(2) Regarding recharging time

Depending on the combination of the charger and batteries, the charging time will become as shown in Table 5.

HOW TO USE

1. Confirm the clutch dial position (See Fig. 5) The tightening torque of this unit can be adjusted according to the clutch dial position, at which the clutch dial is set. (1) When using this unit as a screwdriver, line up the

Table 5 Charging time (At 20°C)

Charger BatteryUC18YG EB912S, EB914S, EB914, EB1212S, EB1214S, EB1214LApprox. 30 min. EB9B, EB1220BLApprox. 50 min.

one of the numbers “1, 3, 5 ... 22” on the clutch dial, or the dots, with the triangle mark on the outer body. (2) When using this unit as a drill, align the clutch dial

” with the triangle mark on the outer body. CAUTION The clutch dial cannot be set between the numerals

The pilot lamp goes off to indicate that the battery is fully charged. The battery charging time becomes longer when a temperature is low or the voltage of the power source is too low. When the pilot lamp does not go off even if more than 120 minutes have elapsed after starting of the charging, stop the charging and contact your HITACHI AUTHORIZED SERVICE CENTER. CAUTION

“1, 3, 5 ... 22” or the dots. Do not use with the clutch dial numeral between

“22” and the line at the middle of the drill mark. Doing so may cause damage (See Fig. 6). 2. Tightening torque adjustment (1) Tightening torque

Tightening torque should correspond in its intensity to the screw diameter. When too strong torque is used, the screw head may be broken or be injured. Be sure to adjust the clutch dial position according to the screw diameter. (2) Tightening torque indication

If the battery is heated due to direct sunlight, etc., just after operation, the charger pilot lamp may not light up. At that time, cool the battery first, then start charging. 3. Disconnect the charger’s power cord from the receptacle 4. Hold the charger firmly and pull out the battery NOTE

The tightening torque differs depending on the type of screw and the material being tightened. The unit indicates the tightening torque with the numbers “1, 3, 5 ... 22” on the clutch dial, and a dots. The tightening toque at position “1” is the weakest and the torque is strongest at the highest number (See Fig. 5).

After charging, pull out batteries from the charger first, and then keep the batteries properly.

drill mark “

Page 5 of the InFocus DS 12DM user manual — NOTE
Pagina 5 · clicca per ingrandire
Pagina 5

(3) Adjusting the tightening torque

Rotate the clutch dial and line up the numbers “1, 3, 5 ... 22” on the clutch dial, or the dots, with the triangle mark on the outer body. Adjust the clutch dial in the weak or the strong torque direction according to the torque you need. CAUTION The motor rotation may be locked to cease while

knob, confirm that the switch is off. Changing the speed while the motor is rotating will damage the gears. When setting the shift knob to “HIGH” (high speed)

and the position of the clutch dial is “17” or “22”, it may happen that the clutch does not engaged and that the motor is locked. In such a case, please set the shift knob to “LOW” (low speed). If the motor is locked, immediately turn the power

the unit is used as drill. While operating the driver drill, take care not to lock the motor. Too long hammering may cause the screw broken

due to excessive tightening. 3. Change rotation speed Operate the shift knob to change the rotational speed. Move the shift knob in the direction of the arrow (See Figs. 7 and 8). When the shift knob is set to “LOW”, the drill rotates at a low speed. When set to “HIGH”, the drill rotates at a high speed.

off. If the motor is locked for a while, the motor or battery may be burnt. 4. The scope and suggestions for uses The usable scope for various types of work based on the mechanical structure of this unit is shown in Table 6.

Drilling Steel Use for drilling purpose.

Machine screw Use the bit or socket matching the screw diameter. Driving

Wood screw Use after drilling a pilot hole.

5. How to select tightening torque and rotational speed

Rotating speed selection (Position of the shift knob)

LOW (Low speed) HIGH (High speed)

Machine screw 1 – 22 For 4 mm or smaller diameter screws.

For 6 mm or smaller diameter screws.

For 6.2 mm or smaller nominal diameter screws. (DS9DM) For 6.8 mm or smaller nominal diameter screws. (DS12DM)

Wood screw 1 –

For 3.8 mm or smaller nominal diameter screws.

For 21 mm or smaller diameters. (DS9DM) For 27 mm or smaller diameters. (DS12DM)

For 18 mm or smaller diameters.

For drilling with a metal working drill bit.

NOTE

The use of the battery EB9H, EB926H, EB930H, EB1222HL, EB1226HL and EB1230HL in a cold condition (below 0 degree Centigrade) can sometimes result in the weakened tightening torque and reduced amount of work. This, however, is a temporary phenomenon, and returns to normal when the battery warms up. 6. Using the hook CAUTION When using the hook, pay sufficient attention so that

be considered as general standard. As different types of tightening screws and different materials to be tightened are used in actual works proper adjustments are naturally necessary. When using the driver drill with a machine screw

at HIGH (high speed), a screw may damage or a bit may loose due to the tightning torque is too strong. Use the driver drill at LOW (low speed) when using a machine screw.

the main equipment does not fall. If the tool falls, there is a risk of accident.

Show 10 more labels / short text on this page
Table 6 · Work Suggestions · Wood · Aluminum · Table 7 · Use Clutch Position · Driving · Wood · Drilling · Metal
Page 6 of the InFocus DS 12DM user manual — MAINTENANCE AND INSPECTION
Pagina 6 · clicca per ingrandire
Pagina 6

Do not attach the tip tool except phillips bit to the tool

NOTE

main unit when carrying the tool main unit with the hook suspended from a waist belt. Injury may result if you carry the equipment suspended from the waist belt with sharp tipped components such as drill bit attached.

If the sleeve is tightened in a state where the clip of the keyless chuck is opened to a maximum limit, a click noise may occur. This is the noise that occurs when the loosening of the keyless chuck is prevented and is not a malfunction. CAUTION

When it is no longer possible to loosen the sleeve, use a vise or similar instrument to secure the bit. Set the clutch mode between 1 and 11 and then turn the sleeve to the loose side (left side) while operating the clutch. It should be easy now to loosen the sleeve. 8. Automatic spindle-lock mechanism This unit has automatic spindle-lock mechanism for quick bit changes. 9. Confirm that the battery is mounted correctly 10. Check the rotational direction The bit rotates clockwise (viewed from the rear side) by pushing the R-side of the selector button. The L-side of the selector button is pushed to turn the bit counterclockwise (See Fig. 16) (The L and

The hook can be installed on the right or left side and the angle can be adjusted in 5 steps between 0° and 80°. (1) Operating the hook

(a) Pull out the hook toward you in the direction

of arrow (A) and turn in the direction of arrow (B) (Fig. 9). (b) The angle can be adjusted in 5 steps (0°, 20°,

40°, 60°, 80°). Adjust the angle of the hook to the desired position for use. (2) Switching the hook position CAUTION

Incomplete installation of the hook may result in bodily injury when used. (a) Securely hold the main unit and remove the

R marks are provided on the body). 11. Switch operation When the trigger switch is depressed, the tool

screw using a slotted head screwdriver or a coin (Fig. 10). (b) Remove the hook and spring (Fig. 11). (c) Install the hook and spring on the other side and

rotates. When the trigger is released, the tool stops. The rotational speed of the drill can be controlled

securely fasten with screw (Fig. 12). NOTE

by varying the amount that the trigger switch is pulled. Speed is low when the trigger switch is pulled slightly and increases as the trigger switch is pulled more. NOTE

Pay attention to the spring orientation. Install the spring with larger diameter away from you (Fig. 12). (3) Using the bit holder Installing the bit

Slide the bit from the side in the direction of Fig. 13, and then insert firmly until the groove on the bit locks in the protruded section of the hook. Removing the bit

A buzzing noise is produced when the motor is about to rotate; This is only a noise, not a machine failure.

Securely hold the main unit and pull out the bit by holding the tip with your thumb (Fig. 14). CAUTION The bit may come loose from the hook and cause

MAINTENANCE AND INSPECTION

1. Inspecting the tool Since use of as dull tool will degrade efficiency and cause possible motor malfunction, sharpen or replace the tool as soon as abrasion is noted. 2. Inspecting the mounting screws Regularly inspect all mounting screws and ensure that they are properly tightened. Should any of the screws be loose, retighten them immediately. Failure to do so could result in serious hazard. 3. Maintenance of the motor The motor unit winding is the very “heart” of the power tool. Exercise due care to ensure the winding does not become damaged and/or wet with oil or water. 4. Inspecting the carbon brushes (Fig. 17) The motor employs carbon brushes which are consumable parts. Since and excessively worn carbon brush can result in motor trouble, replace the carbon brush with new ones when it becomes worn to or near the “wear limit”. In addition, always keep carbon brushes clean and ensure that they slide freely whthin the brush holders. NOTE

bodily injury when reversing the direction of the bit as shown in Fig. 13 or when using the driver with the bit stored incomplete. Only Hitachi OPTIONAL ACCESSORIES plus driver

bits (Bit No. 2; Code No. 992671, Bit No. 3; Code No. 992672) may be used. Do not use other bits since they may come loose. 7. Mounting and dismounting of the bit (1) Mounting the bit

Loosen the sleeve by turning it toward the left (in the counterclockwise direction as viewed from the front) to open the clip on the keyless chuck. After inserting a driver bit, etc., into the keyless drill chuck, and tighten the sleeve by turning it toward the right (in the clockwise direction as viewed from the front) (See Fig. 15). If the sleeve becomes loose during operation, tighten it further. The tightening force becomes stronger when the sleeve is tightened additionally. (2) Dismounting the bit

When replacing the carbon brush with a new one, be sure to use the Hitachi Carbon Brush Code No. 999054.

Loosen the sleeve by turning it toward the left (in the counterclockwise direction as viewed from the front), and then take out the bit etc. (See Fig. 15).

Page 7 of the InFocus DS 12DM user manual — MAINTENANCE AND INSPECTION
Pagina 7 · clicca per ingrandire
Pagina 7

5. Replacing carbon brushes Take out the carbon brush by first removing the brush cap and then hooking the protrusion of the carbon brush with a flat head screw driver, etc., as shown in Fig. 19. When installing the carbon brush, choose the direction so that the nail of the carbon brush agrees with the contact portion outside the brush tube. Then push it in with a finger as illustrated in Fig. 20. Lastly, install the brush cap. CAUTION

Be absolutely sure to insert the nail of the carbon brush into the contact portion outside the brush tube (You can insert whichever one of the two nails provided). Caution must be exercised since any error in this operation can result in the deformed nail of the carbon brush and may cause motor trouble at an early stage. 6. Cleaning on the outside When the driver drill is stained, wipe with a soft dry cloth or a cloth moistened with soapy water. Do not use chloric solvents, gasoline or paint thinner, for they melt plastics. 7. Storage Store the driver drill in a place in which the tempera ture is less than 40°C and out of reach of children. 8. Service parts list A : Item No. B : Code No. C : No. Used D : Remarks CAUTION

Repair, modification and inspection of Hitachi Power Tools must be carried out by a Hitachi Authorized Service Center. This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance. In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed. MODIFICATIONS

Hitachi Power Tools are constantly being improved and modified to incorporate the latest technological advancements. Accordingly, some parts (i.e. code numbers and/or design) may be changed without prior notice.

Information concerning airborne noise and vibration The measured values were determined according to EN50144.

The typical A-weighted sound pressure level: 70 dB (A). (DS12DM) Wear ear protection.

The typical weighted root mean square acceleration value: 2.0m/s2. (DS12DM)

Codici sul display

Codici di errore

Il significato dei codici di errore mostrati sul display e come cancellarli.

CodiceSignificatoRisolvi
EB926HNi-MH 9.6 V (2.6 Ah, 8 cells) EB1226HL : Ni-MH 12 V (2.6 Ah, 10 cells) p.2
EB930HNi-MH 9.6 V (3.0 Ah, 8 cells) EB1230HL : Ni-MH 12 V (3.0 Ah, 10 cells) p.2

Fai una domanda su InFocus DS 12DM

I possessori del prodotto e il nostro team di solito rispondono entro 24 ore, e la tua domanda sarà utile anche ad altri.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Nessuna domanda ancora per il dispositivo InFocus DS 12DM

Invia la prima domanda: risponderanno altri possessori o il nostro team.

Documento originale

InFocus DS 12DM manuale in PDF

78 pagine·1.2 MB·Trapano a batteria·PDF
Clicca su qualsiasi pagina in alto per aprirla qui
Pagina 1 / …
100%
Caricamento pagine…