Manuale d’uso / di manutenzione del prodotto MWM 1801 del fabbricante Impex
Vai alla pagina of 29
NOTE: Please read all i nstructions caref ully befor e using this product Table of Contents Safety Notice Hardware Pack Assembly Instruc tion Parts L ist Resistance Chart Warranty Ordering Parts Model MW M 1801 Retain This Manual for Reference 08-18-03 OWNER'S MANUAL MARCY HOME GYM MWM 1801 IMPEX FITNESS PRODUCTS 14777 DON JULIAN RD.
TA BLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFET Y NOTICES...................................................................……….. 2 HARDW ARE PACK……….
IMPORTANT SAFETY NOTICE PRECA UTIONS This exerci se machine is bui lt for optimum safety. How ever , certain precauti ons apply whenev er you operate a piece of exer cise equi pment. Be sure to read the entir e manual before you assemble or operate your machine.
HARDWARE PACK 3.
HARDWARE PACK 4.
A SSEMBLY INSTRUCTION Tools Required A ssembling the Machine: Tw o Adj ustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended this machine to be assembled by tw o or more people to avoid possible inj ury. STEP 1 (See Diagram 1) A.) Attach the Lef t Base Frame (#3) to the Ri ght Base Frame ( #1).
STEP 2 (See Diagram 2) A.) Attach the Right Vertical Beam (#2) to the Ri ght Base Frame ( #1). Secure it w ith two M10 x 2 ½” Carri age Bolts ( #82), ∅ ¾” W ashers (#93), and M10 Ai rcraft Nuts (#90) . NOTE: Do not tighten the N uts and Bolts yet.
STEP 3 (See Diagram 3) A.) Alig n four ∅ 2 ½ ” x 1” Rubber Bumper s (#68) to the holes on the R ight Base Fr ame (#1). Insert four Gui de Rods (#5) thr ough the Rubber Bumpers into the holes on the Right Base Fr ame. Slide tw o Selector Stems (#35) onto the Guide Rods.
DIAGRAM 3 8.
STEP 4 (See Diagram 4) A.) Attach the Left Vertical Beam (#4) to the Left Base Frame (#3) . Secure it w ith two M10 x 2 ½ ” Carriage Bol ts (#82), ∅ ¾” W ashers (#93), and M 10 Aircr aft Nuts (#90). B.) Attach the Left Upper Frame (#11) to the Top Socket Assembly (#7) and the Left Vertical Beam.
DIAGRAM 4 10.
STEP 5 (See Diagram 5) A.) Attach the Front Press Base (#15) to the Left Base Frame (#3). Secure i t wi th a M10 x 9 ¼ ” Axle (#50), tw o ∅ ¾” W ashers (#93), and tw o M10 Aircraft Nuts (#90). B.) Attach the two Front Presses (#16) to the Front Press Base (#15) .
STEP 6 (See Diagram 6) A.) Insert the axle on the Left Butterfly ( #12) throug h the hole on the Left Upper Frame (#11) from the bottom up. Sli de a ∅ 1 ½” W asher (#54) and ∅ 1 3/8” Lock Ri ng (#53) onto the Axle. Al ign the hol es and secure the Ring wi th a M6 x 1 5/8” Hex Bolt (#87) and M6 Aircr aft Nut (#91).
Cable Loop Diagram f or Butterfly Stat ion 13.
Cable Loop Diagram f or Bench Press Station 14.
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach the two Swiv el Pulley Brackets ( #42) to the Left Upper Frame ( #11). Secure each Bracket w ith one M12 x 4 3/8” Allen Bol t (#76), tw o ∅ 1” W ashers (#92) and one M12 Air craft Nut (#89).
STEP 8 (See Diagram 8 & Cable Loop Diagram) A.) Attach a Chain (#51) to the Left Vertical Beam (#4) . Secure it w ith one M10 x 1 3/8” Allen Bolt ( #83), tw o ∅ 3/4” W ashers (#93), and one M10 Aircr aft Nut (#90). Attach one end of the 136” Butterfly Support C able (#31) to the C hain using a C-cli p (#63).
STEP 9 (See Diagram 9 & Cable Loop Diagram) A.) Attach one end of the140” Leg Press C able (#28) to the openi ng hole on the Left Seat Support (#14), under neath the rubber bumper . Secure it w ith one M10 x 2 3/8” All en Bolt (#79), tw o ∅ ¾” W ashers (#93), and one M 10 Aircraft Nut ( #90).
DIAGRAM 9 18.
STEP 10 (See Diagram 10 & Cable Loop Diagram) A.) Attach the 114” Upper Cable (#26) to the f ront opening on the Ri ght Upper Frame (#6). NOTE: The Ball Stopper on the Cabl e needs to be underneath the Frame. B.) Attach a Pulley (#65) to the opening.
STEP 11 (See Diagram 11 & Cable Loop Diagram) A.) Attach the 39” AB Cable (#30) to the opening on the Right Vertical Beam (#2). Attach a Pulley to the opening. Secur e the Pulley wi th one M10 x 2 3/8” Allen Bol t (#79), tw o ∅ 5/8” x ½ ” Pulley Bushing s (#58), and one M 10 Aircr aft Nut (#90).
DIAGRAM 11 21.
STEP 12 (See Diagram 12) A.) Now move the machine to its fina l p o sition. Af ter insta llin g th e weight stack, it will be too he avy to move. Check and ti ghten all N uts and Bolts prev iously installed. B.) Install 9 W eight Plates (#36) to each set of Guide Rods (#5).
STEP 13 (See Diagram 13) A.) Insert one Foam Tube (#34) halfway through the hol e on the Rig ht Seat Support (#8) . Insert one Foam Tube (#34) halfway through the hole on the Leg D eveloper (#9). Push four Foam Rolls ( #38) onto the Tubes from both sides.
STEP 14 (See Diagram 14) A.) Attach a Backrest Board (#23) to the Left Vertical Beam (#4). Secur e it wi th two M 8 x 2 1/8” Allen Bolts ( #84) and ∅ 5/8” W ashers (#94). B.) Place the Seat (#22) onto the Left Seat Support (#14). Secur e it w ith two M 8 x 2 1/8” Allen Bolts (#84) and tw o ∅ 5/8” W ashers (#94).
HOW TO USE How to u se the qu ick release con nector. The Clip is removed from the Connector. Connector Clip Place the chain in between the connector and insert the Clip through the holes.
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Right Base Fram e 1 2 Right Vertical Beam 1 3 Left Base F ram e 1 4 Left Vertic al Beam 1 5 Guide Rod 4 6 Right Upper Fram e 1 7 Top Soc ket As sem bly 1 8 Righ.
MWM 1801 Weight Resistance Chart Weight Plate Station 1 2 3 4 5 6 7 8 9 Low Pulley 30 42 54 66 78 90 102 114 126 Lat Pu ll 31 42 53 64 75 86 97 108 119 Ab Strap 30 42 54 66 78 90 102 114 126 Butterfly 20 26 32 38 44 50 56 62 68 Leg Press 66 100 134 168 202 236 270 304 338 Front Press 44 63 82 101 120 139 158 177 196 *Each plate weights 10 lb.
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ( "IMPEX") warrants this produc t to be f ree from def ects in work m ans hip and m aterial, under norm al use and s ervic e conditions , f or a per iod of two years on the F ram e f r om the date of purchase.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Impex MWM 1801 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Impex MWM 1801 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Impex MWM 1801 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Impex MWM 1801 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Impex MWM 1801, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Impex MWM 1801.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Impex MWM 1801. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Impex MWM 1801 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
