Manuale d’uso / di manutenzione del prodotto CG 1400 del fabbricante Impex
Vai alla pagina of 24
NOTE: Please read all i nstructions caref ully befor e using this product Table of Contents Safety Notice Hardware Identifier Assembly Instruc tion Parts L ist Resistance Chart Warranty Ordering Parts Model CG 1400 Retain This Manual for Reference 07-23-04 OWNER'S MANUAL COMPETITOR HOME GYM CG 1400 IMPEX FITNESS PRODUCTS 14777 DON JULIAN RD.
TA BLE OF CONTENTS BEFORE YOU BEGIN....................................................................................……….. 1 IMPORTANT SAFET Y NOTICE...................................................................……….. 2 HARDW ARE IDENTIFIER.
IMPORTANT SAFETY NOTICE PRECA UTIONS This exerci se machine is bui lt for optimum safety. How ever , certain precauti ons apply whenev er you operate a piece of exer cise equi pment. Be sure to read the entir e manual before you assemble or operate your machine.
HA RDWA RE PA CK 3.
HA RDWA RE PA CK 4.
HA RDWA RE PA CK 5.
A SSEMBLY INSTRUCTION Tools Required A ssembling the Machine: Tw o Adj ustable Wrenches, two Allen Wrenches, and one Flat Head Screw driver. NOTE: It is strongly recommended this machine to be assembled by tw o or more people to avoid possible inj ury.
STEP 2 (See Diagram 2) A.) Attach the Front Upper Vertical Beam (#5) to the Front Low er Vertical Beam (#82) . Secure it with tw o M10 x 2 ½” Carri age Bolts ( #42), ∅ ¾” W ashers (#53), and M10 Air craft Nuts (#55).
STEP 3 (See Diagram 3) A.) Attach the Front Lower Verti cal Beam (#82) , both Left and Right Storag e Frames (#15)&(#16) to the Main Base Frame ( #6). Secure them tog ether w ith tw o M10 x 3” Carriage Bolts (#73), ∅ ¾ ” W ashers (#53) and M10 Aircr aft Nuts (#55).
STEP 4 (See Diagram 4) A.) Slide the W eight Hol der (#2) onto the R ear Verti cal Beam (#1) from the top. B.) Attach the rear end of Upper Frame (#4) to the R ear Upper Ver tical Beam ( #1). Secure the upper hole w ith a Small Bracket (#20), M 10 x 2 3/8” Al len Bolt ( #46), and ∅ ¾” W asher (#53).
STEP 5 (See Diagram 5) A.) Attach the Front Press Base (#12) to the Upper Frame ( #4). Secure it w ith one 5 7/8” Axle (#60), tw o ∅ 1” Axle W ashers (#64), and two M10 Ai rcraft Nuts (#55) . Do not ov er tighten the nuts. Make sure the Base is abl e to swiv el.
STEP 6 (See Diagram 6) A.) Attach the Leg Developer (#11) to the bracket on the M ain Seat Support (#7) . Secure it w ith one M10 x 3” Allen Bolt (#44), tw o ∅ ¾” W ashers (#53), and one M10 Air craft Nut (#55). D o not over ti ghten the Bolt. M ake the Leg Dev eloper is able to sw ivel .
STEP 7 (See Diagram 7) A.) Insert the axle on the Ri ght Butterfly Arm (#14) through the r ight piv ot hole on the Front Press Base (#12). Sl ide a ∅ 1 ½” W asher (#54) and Ri ng Cap ( #68) onto the ax le. Secure the Cap w ith a M6 x 1 ¼” Al len Bolt (#63) and M6 Airc raft Nut (#56).
Cable Loop Diagram 13.
STEP 8 (See Cable Loop Diagram & Diagram 8) A.) Attach the 129.9” Upper Cable (#31) to the open bracket in the front of Upper Frame ( #4). Attach a Pulley (#28) to the open bracket. Secur e it w ith one M10 x 1 ¾” Allen Bolt (#45), two ∅ ¾ ” W ashers (#53), and one M10 Airc raft Nut (#55).
DIAGRAM 8 15.
STEP 9 (See Cable Loop Diagram & Diagram 9) A.) Attach one end of the 116” Butterfly C able (#29) to the Hook on the Rig ht Butterfly Ar m (#14).
STEP 10 (See Cable Loop Diagram & Diagram 10) A.) Insert the 151.6” Lower Cable (#30) through the opening on bottom of the Leg Devel oper (#11). Attach a Pul ley (#28) to the opening . Secure it with one M10 x 2 3/8” Allen Bol t (#46), tw o ∅ 7/8” Pulley Bushing s (#51), and one M10 Aircr aft Nut (#55).
DIAGRAM 10 18.
STEP 11 (See Diagram 11) A.) Attach a Butterfly Arm Pad (#24) to the R ight Butter fly Arm ( #14). Secure it w ith two M8 x 2” Allen Bol ts (#74) and ∅ 5/8” W ashers (#52). Repeat the same pr ocedure to install the other side. B.) Attach the Backrest Board (#23) to the Front Upper Vertical Frame (#5).
STEP 12 (See Diagram 12) A.) Insert two Foam Roll Tubes (#27) halfway through the holes on the Main Seat Suppor t (#7) and Leg Dev eloper (#11). Push four Foam Rolls ( #26) onto the tubes. B.) Connect the Arm Curl Handl e (#70) to the Low er Cable wi th two C -clips ( #57) and one Long Chain (#79) .
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Rear Upper Vertic al Beam 1 2 W eight Holder 1 3 Rear Stabilizer 1 4 Upper Fram e 1 5 Front Upper Ver tical Beam 1 6 Main Base Fram e 1 7 Main Seat Support 1 8 .
WEIGHT RESISTANCE CHART The following chart shows the approxim ate weight resistance ratio at each station. Weight resistance shows for the butterfly station is for each butterfly arm. The actual resistance at each station m ay vary due to friction and differences in each individual plate .
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ( "IMPEX") warrants this produc t to be f ree from def ects in work m ans hip and m aterial, under norm al use and service c onditions, for a per iod of two y ear s on the Fram e from the date of purchase.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Impex CG 1400 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Impex CG 1400 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Impex CG 1400 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Impex CG 1400 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Impex CG 1400, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Impex CG 1400.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Impex CG 1400. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Impex CG 1400 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
