Manuale d’uso / di manutenzione del prodotto P76 del fabbricante IBM
Vai alla pagina of 38
3-867-449- 11 (1) Operating Instructions Mode d’emploi Bedienungsanleitung Manual de instrucciones Istruzioni per l’uso P76 Color Monitor FR GB DE ES IT.
.
i Getting Started Getting Started DANGER To avoid shock hazard: • Do not remove the covers. • Do not operate this product unless the stand is attached. • Do not connect or disconnect this product during an electrical storm. • The power cord plug must be connected to a properly wired and grounded power outlet.
ii PELIGRO Para evitar riesgos de descargas eléctricas: • No retire bajo ningún concepto las cubiertas. • No maneje el monitor sin antes acoplar el soporte. • No conecte ni desconecte el equipo de una toma de alimentación durante una tormenta eléctrica.
iii Getting Started Getting Started FARE Slik unngår du fare for elektrisk støt: • Ikke ta av dekslene. • Ikke bruk produktet dersom sokkelen ikke er montert. • Ikke koble produktet til eller fra under tordenvær. • Pluggen på strømledningen må kobles til korrekt montert og jordet strømuttak.
iv TEHLİKE Elektrik çarpması tehlikesinden kaçınmak için: • Kapakları çıkarmayınız. • Bu cihazı kaidesine takılı durumda değilken çalıştırmayınız. • Bu cihazı elektriksel fırtına sırasında prize takmayınız veya prizden çıkarmayınız.
Getting Started Getting Started F GB ES C English.
Edition 1 This publication could contain technical inaccuracies or typographical errors. Changes are made periodically to the information herein; these changes will be made in later editions. IBM may make improvements and/or changes in the product(s) and/or program(s) at any time.
1 Getting Started F GB ES C T ABLE OF CONTENTS • E NERGY S TAR is a U.S. registered mark. • Trinitron ® is a registered trademark of Sony Corporation. • VGA is a registered trademark of IBM Corporation of the U.S.A. • VESA is a trademark of Video Electronics Standard Association.
2 Getting Started Use of the Tilt-Swivel This monitor can be adjusted within the angles shown below. To find the center of the monitor’s turning radius, align the center of the monitor’s screen with the centering dots on the stand. Hold the monitor at the bottom with both hands when you turn it horizontally or vertically.
3 Getting Started Getting Started F GB ES C Identifying P arts and Contr ols See the pages in parentheses for further details. Front 1 ? (reset) button (page 13) Resets the adjustments to the factory settings. 2 ¨ (brightness) down and up ( . / > ) buttons (pages 5 – 13) Adjust the picture brightness.
4 Getting Started to a power outlet to AC IN Power cord To a computer with an HD15 video output Setup This monitor works with platforms running at horizontal frequencies between 30 and 96 kHz.
5 Getting Started F GB ES C Customizing Your Monitor Before adjusting • Connect the monitor and the computer, and turn them on. Selecting the On-scr een Display Language If you need to change the OSD language, see “Using the LANGUAGE On-screen Display” on page 10.
Customizing Your Monitor 6 To adjust the horizontal centering of the picture adjust the vertical centering of the picture adjust the horizontal size of the picture adjust the vertical size of the pict.
7 Getting Started F GB ES C Customizing Your Monitor Using the GEOMETR Y On- screen Display The GEOMETRY settings allow you to adjust the shape and orientation of the picture. Once the (Rotation) is adjusted, it will be stored in memory for all input signals received.
8 Customizing Your Monitor 9300 K 5000 K C OLO R Using the COLOR On-scr een Display You can change the monitor’s color temperature. For example, you can adjust or change the colors of a picture on the screen to match the actual colors of the printed picture.
Getting Started Customizing Your Monitor F GB ES C 9 Using the CONVERGENCE On- screen Display The CONVERGENCE settings allow you to adjust the quality of the picture by controlling the convergence. The convergence refers to the alignment of the red, green, and blue color signals.
10 Customizing Your Monitor Using the LANGU AGE On- scr een Display English, French, German, Spanish, Italian, Dutch, Swedish, Russian and Japanese versions of the OSDs are available. 1 Press the button. The MENU OSD appears. 2 Press the . / > buttons to select “ LANGUAGE,” and press the button again.
11 Getting Started F GB ES C Customizing Your Monitor Changing the on-screen display position You can change the OSD position (for example, when you want to adjust the picture behind the OSD). 1 Press the button. The MENU OSD appears. 2 Press the . / > buttons to select “ OPTION,” and press the button again.
12 Customizing Your Monitor Locking the controls You can protect adjustment data by locking the controls. 1 Press the button. The MENU OSD appears. 2 Press the . / > buttons to select “ OPTION,” and press the button again. The OPTION OSD appears.
13 Getting Started F GB ES C Customizing Your Monitor Resetting the Adjustments Resetting an adjustment item 1 Press the , . / > buttons to select the OSD containing the item you want to reset. 2 Press the . / > buttons to select the item you want to reset.
14 Technical Features Plug & Play This monitor complies with the DDC 1, DDC2B and DDC2Bi Display Data Channel (DDC) standards of VESA. When a DDC1 host system is connected, the monitor synchronizes with the V. CLK in accordance with the VESA standards and outputs the EDID (Extended Display Identification Data) to the data line.
15 Getting Started F GB ES C Technical Features Preset Modes No. 1 2 3 4 5 6 7 8 Resolution (dots × lines) 640 × 480 640 × 480 640 × 480 800 × 600 800 × 600 1024 × 768 1024 × 768 1280 × 1024 Horizontal Frequency 31.5 kHz 37.5 kHz 43.3 kHz 46.
16 Additional Information T roubleshooting This section may help you isolate the cause of a problem and as a result, eliminate the need to contact technical support.
17 Getting Started F GB ES C Additional Information Additional Information Symptom Check these items Screen image is not centered or sized properly Edges of the image are curved White lines show red o.
18 Additional Information Specifications Picture tube 0.24 mm aperture grille pitch 17 inches measured diagonally 90-degree deflection Viewable image size Approx. 327 × 243 mm (w/h) (12 7 / 8 × 9 5 / 8 inches) 16.0” viewable diagonal Resolution Horizontal: Max.
I Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
II MPRII This product complies with Swedish National Council for Metrology (MPR) standards issued in December 1990 (MPRII) for very low frequency (VLF) and extremely low frequency (ELF).
III European Union (EU) Statement This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to CISPR 22 / European Standard EN 55022.
IV Statement of Limited Warranty U.S., Canada and Puerto Rico The warranties provided by IBM in this Statement of Limited Warranty apply only to Machines you originally purchase for your use, and not for resale, from IBM or your reseller.
V Extent of Warranty IBM does not warrant uninterrupted or error-free operation of a Machine. The warranties may be voided by misuse, accident, modification, unsuitable physical or operating environme.
VI Congratulations! You have just purchased a TCO’95 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also, to the further development of environmentally adapted electronics products.
Getting Started Appendix VII On this page, you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from: TCO Development Unit S-114 94 Stockholm Sweden Fax: +46 8 782 92 07 Email (Internet): development@tco.
VIII Congratulations! You have just purchased a TCO’99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
Getting Started Appendix IX Labelled products must meet strict environmental demands, for example, in respect of the reduction of electric and magnetic fields, physical and visual ergonomics and good usability. Below you will find a brief summary of the environmental requirements met by this product.
X Service Information The following parts are for use by IBM service, or IBM authorized dealers, to support customer warranty. Parts are for service use only.
Getting Started Getting Started XI.
Printed in Japan P202 User Guide P ar t Number 61H0239 EC D03285 *61H0239*.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il IBM P76 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del IBM P76 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso IBM P76 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul IBM P76 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il IBM P76, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del IBM P76.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il IBM P76. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo IBM P76 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
