Manuale d’uso / di manutenzione del prodotto YT155 del fabbricante Husqvarna
Vai alla pagina of 68
YT155 Manuale di istruzioni Prima di utilizzare la macchina leggete queste istruzioni con attenzione ed accertatevi di averle comprese bene. Instructieboekje Lees deze instructies aandachtig en zorg dat u ze begrijpt voordat u deze machine gebruikt.
2 3 18 25 33 36 43 61 64 Safety rules. Reglas de seguridad. Sicherheitsvorschriften. Norme antinfortunistiche. Règles de sécurité. Veiligheidsregels. Assembly. Montaje. Zusammenbau. Montaggio. Montage. Montering. Functional description. Descripción del funcionamiento.
3 1. Safety Rules Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I .
4 IV. Maintenance and Storage • Keep all nuts, bolts and screws tight to be sure the equipment is in safe working condition. • Never store the equipment with petrol in the tank inside a building where fumes may reach an open flame or spark. • Allow the engine to cool before storing in any enclosure.
5 • Vor dem Gebrauch immer mit einer Sichtprüfung sicherstellen, daß Mähmesser, Messerschrauben und die Mäheinheit nicht abgenutzt oder beschädigt sind. Abgenutzte oder beschädigte Messer und Schrauben ersetzen, um Auswuchtung zu gewährleisten.
6 • Vor dem Verlassen der Bedienungsstation: - Die Zapfwelle abstellen und alle Anbaugeräte absenken. - In Leerlauf schalten und die Feststellbremse einlegen. - Den Motor abstellen und den Zündschlüssel abziehen. • Alle Anbaugeräte-Antriebe ausschalten, den Motor abstellen und das (die) Zündkerzenkabel abziehen bzw.
7 III. UTILISATION • Ne démarrez jamais le moteur à l'intérieur d'un bâtiment où des vapeurs dangereuses de monoxyde de carbone pourraient s'être accumulées. • Tondez uniquement à la lumiére du jour ou avec une bonne lumière artificielle.
8 • Débrayez les lames, arrêtez le moteur, et débranchez le (s) fil (s) de la bougie d'allumage ou enlevez la clef de contact: - avant de retirer l'insert broyeur ou avant de retirer la goulotte d'éjection pour la nettoyer.
9 1. Reglas De Seguridad Prácticas de Operación Seguras para las Segadoras Conducibles IMPORTANTE: ESTA MAQUINA CORTADORA ES CAPAZ DE AMPUTAR LAS MANOS Y LOS PIES Y DE LANZAR OBJETOS. SI NO SE OBSERVAN LAS INSTRUCCIONES DE SEGURIDAD SIGUIENTES SE PUEDEN PRODUCIR LESIONES GRAVES O LA MUERTE.
10 • Desenganche la transmisión a los accesorios, pare el motor, y desconecte el (los) cable (s) de la bujía o remueva la llave de ignición - antes de limpiar bloqueos o desatrancar del conducto; - antes de inspeccionar, limpiar o trabajar sobre la segadora; - después de golpear un objeto extraño.
11 I . ADDESTRAMENTO ALL’USO • Studiare attentamente le istruzioni. Acquisire dimestichezza con i comandi e conoscere a fondo l’uso corretto dell’equipaggiamento. • Non consentire mai l’uso dei trattorini tosaerba ai bambini né agli adulti che non abbiano dimestichezza con le istruzioni sull’uso.
12 • Disinnestare la trasmissione del moto agli accessori, spegnere il motore e scollegare i fili delle candele oppure togliere la chiavetta di accensione: - prima di pulire eventuali intasamenti e .
13 I . TRAINING • Lees de instructies aandachtig. Zorg dat u vertrouwd bent met de bedieningselementen en het juiste gebruik van de machine. • Laat kinderen of mensen die niet bekend zijn met de instructies, de maaimachine niet gebruiken. Het is mogelijk dat plaatselijke voorschriften een beperking stellen aan de leeftijd van de bestuurder.
14 • Schakel de aandrijving naar de hulpstukken uit, stop de motor en maak de bougiekabel(s) los of verwijder het contactsleuteltje, - voordat u opgehoopt materiaal weghaalt of een verstopte afvoer leeg maakt; - voordat u de maaimachine controleert, schoonmaakt of eraan werkt; - nadat u een ongewenst voorwerp heeft geraakt.
15 BATTERY BATTERIE BATTERIE ACCU BATERÍA BATTERIA CAUTION VORSICHT DANGER OPGELET PRECAUCIÓN ATTENZIONE BEWARE OF THROWN OBJECTS VORSICHT, HOCHGESCHLEUDERT GEGENSTÄNDE ATTENTION AUX PROJECTILES LE.
16 These symbols may appear on your tractor or in the literature supplied with the product. Learn and understand their meaning. Diese Symbole finden Sie auf Ihrer Maschine oder in Unterlagen, die mit dem Produkt ausgehändigt wurden. Bitte machen Sie sich mit deren Bedeutung vertraut.
17 GEFAHR AUGEN SCHÜTZEN EXPLOSIVE GASE KÖNNEN ERBLINDUNG UND KÖRPERVERLETZUNGEN VERURSAC-HEN. GEVAAR OGEN BESCHERMEN EXPLOSIEVE GASSEN KUNNEN BLINDHEID OF LETSEL VEROORZAKEN. PELIGRO PROTEJE SUS OJOS GASES EXPLOSIVOS PUEDEN CAUSAR CEGUE-DAD O LESIONES.
18 2. Assembly . 2. Zusammenbau. 2. Montage. 2. Montaje 2. Montaggio. 2. Montering. Before the tractor can be used certain parts must be as- sembled, which for transportation reasons are enclosed in the packing. The picture shows which parts must be as- sembled.
19 2 VOLANTE DE DIRECCIÓN • Introduzca el eje de extensión (1). Apriete en forma segura. • Montar la cubierta del eje del volant. Assegurarse de que las espigas de guía de la cubierta encajan en los orificios respectivos. • Remueva el adaptador del volante y deslice el adaptador sobre la extensión del eje de dirección.
20 2 NOTE! Check that the flex is correctly connected to the safety switch (3) on the seat holder. HINWEIS! Prüfen, daß das Kabel richtig an dem Sicherheitsschalter (3) auf dem Halter des Sitzes angeschlossen ist. REMARQUE! Vérifier que le cordon est correctement branché à l’interrupteur de sécurité (3) sur le support du siège.
21 2 Install battery NOTE: If battery is put into service after month and year indicated on label, charge battery for minimum of one hour at 6-10 amps. WARNING: Before installing battery remove metal brace- lets, wrist watch bands, rings, etc. from your person.
22 2 1. Asiento 2. Cubierta Terminal 3. Cable 4. Cable A. Frontal de tractor 5. Protección 6. Terminal de batería 7. Batería 1. Vando sedile 2. Coprimorsetti 3. Cavo 4. Cavo A. Lato anteriore del trattore 5. Paraurti 6. Polo della batteria 7. Batteria 1.
23 2 WARNING: Positive terminal must be connected first to prevent sparks from accidental grounding. Remove terminal caps and discard. Connect the red cable to + and then the black earth cable to -. Screw tight the cables. Grease the battery poles with vaseline to prevent corrosion.
24 2 Eng TO ADJUST GAUGE WHEELS Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain con- ditions.
25 7 5 8 4 2 3 6 1 Positioning of controls 1. Light Switch. 2. Throttle control. 3. Brake and clutch pedal. 4. Gear shift lever. 5. Connection/disconnection of the cutting unit. 6. Quick lifting/lower of the cutting unit. 7. Ignition lock. 8. Parking Brake.
26 3 Emplacement des commandes 1. Interrupteur des phares. 2. Commande de gaz. 3. Pédale de frein et d'embrayage. 4. Levier de changement de vitesse. 5. Embrayage et débrayage du groupe de coupe. 6. Abaissement et relevage du plate au de coupe.
27 3 Eng Esp 1. Light switch 1. Lichtschalter 1. Interrupteur des phares 1. Interruptor de alumbrado 1. Interruttore luci 1. Schakelaar verlichting F NL 2. Throttle control The throttle control regulates the engine revs and thus the rotation speed of the blades.
28 3. Brake and clutch pedal When the pedal is pushed down the brake is applied and the motor is disengaged. 3. Brems- und Kupplungspedal Beim Vorwärtsdrücken des Pedals wird das Fahrzeug abge- bremst. Gleichzeitig wird der Motor ausgekuppelt und das Fahrzeug rollt aus.
29 3 5. Connection/disconnection of the cutting unit Move the lever forward to connect the drive to the cutting unit, whereby the drive belt is tensioned and the blades begin to rotate. If the lever is moved backwards the drive will be disconnected and the rotation of the blades slowed down by the action of the brake shoes on the pulley.
30 3 OFF ON START 7. Serrure de contact La clé de contact peut être à trois positions : O F F Le courant électrique est coupé ON Le courant électrique est branché START Le démarreur est en circuit ATTENTION! Quand la machine reste sans surveillance, ne jamais laisser la clef de contact dans le contacteur.
31 3 8. Frein de parking Pour enclencher le frein de parking : 1. Enfoncer à fond la pédale de frein/embrayage. 2. En même temps, relever vers le haut le levier du frein de parking et le maintenir dans cette position. 3. Relâcher la pédale de frein.
32 3 10. Choke control When the engine is cold the choke should be pulled out before starting. When the engine has started and is running smoothly push the choke in. 10. Kaltstartregler Bei kaltem Motor ist der Kaltstartregler herauszuziehen, bevor ein Startversuch gemacht wird.
33 4.Before Starting. 4. Maßnahmen vor dem Anlassen. 4. A vant de démarrer . 4. Antes del arranque. 4. Prima dell' avviamento. 4. Maatregelen vóór het starten. Eng Esp Filling up The engine should be run of pure (not oil mixed) unleaded petrol.
34 4 ADD FULL CAUTION - DO Oil level The combined oil refilling cap and the oil stick is accessible when the bonnet is lifted forwards. The oil level in the engine should be checked before each run. Make sure that the tractor is horizontal. Unscrew the oil stick and wipe clean.
35 4 Tire air pressure Check the tire pressure regularly. The pressure in the front tires should be 1 bar (14 PSI) and 0.8 bar (12 PSI) in the back tires. Reifendruck Den Luftdruck in den Reifen regelmäßig prüfen. Der Druck in den Vorderreifen soll 1 bar betragen, in den Hinterreifen 0,8 bar.
36 5. Driving. 5. Betrieb. 5. Conduite. 5. Conducción. 5. Guida. 5. Rijden. Press down the clutch/brake pedal completely and hold down. Set the gear lever in neutral ”N”. Kupplungs- und Bremspedal ganz durchtreten und in dieser Stellung halten. Getriebeschalthebel auf Leerlauf ”N” stellen.
37 5 Warm motor: Push the gas control half-way to full gass position " ". Eng F Esp NL Turn the ignition key to “START position”. NOTE! Do not run the start motor more than 5 seconds at once. If the engine will not start, wait about 10 seconds before the next try.
38 5 NOTA! La máquina tiene un interruptor de seguridad que corta la corriente al motor si el conductor sale del asiento con el motor en marcha y con la palanca de acoplamiento/ desacoplamiento en la posición de acoplamiento.
39 5 Cutting tips • Clear the lawn from stones and other objects which can be thrown away by the blades. • Localize and mark stones and other fixed objects to avoid collision. • Begin with a high cutting height and reduce until the required cutting result is obtained.
40 5 Consigli per il taglio dell’erba • Pulire il prato da pietre e altri corpi estranei. • Individuare ostacoli fissi. • Cominciare con un’altezza di taglio elevata e scendere progressivamente. • I migliori risultati si ottengono con un elevato regime del motore (lame che girano veloci) e marcia bassa (la macchina si muive lentamente).
41 5 Drive in right turns so that the cut grass is thrown away from flower beds and paths, etc. For larger lawns the drive direc- tion should be changed after 2-3 turns so that the cut grass is thrown towards the area that has already been cut as shown in the illustration.
42 5 WARNING! Do not leave the ignition key in the machine when not in use to prevent children and other unauthorized persons starting the engine. WARNUNG! Den Zündschlüssel niemals im Zündschloß sitzen lassen, wenn die Machine unbeaufsichtigt verlassen wird, damit nicht Kinder und unbefugte Personen den Motor anlassen können.
43 1 2 6. Maintenance, adjustment. 6. W ar tung (Instandhaltung), Einstellung. 6. Entretien, réglages. 6. Mantenimiento, ajuste. 6. Manutenzione. 6. Onderhoud, afstelling. WARNING! Before servicing the engine or cutting unit the following shall be carried out: • Press down the clutch/brake pedal and engage the parking brake lever.
44 6 1 2 Capot moteur • Soulever le capot. • Déconnecter les phares, • Se placer devant le tracteur, prendre le capot par les côtés, l'incliner à l'avant, puis le soulever pour le .
45 6 Maintenance NOTE : Periodic maintenance should be performed on a regular basis in order to keep your tractor in good running condition. WARNING : Disconnect spark plug wire to prevent accidental starting before attempting any repair, inspection, or mainte- nance.
46 6 To service engine See engine manual. Oil drain valve • Remove cap and install drain tube. • To open valve, push in slightly, turn counterclockwise and pull out. • To close valve, push in and turn clockwise . • Remove drain tube and install cap.
47 6 Change engine oil ................................................................................................ • Lubricate pivot points ........................................................................ • Check brake operation .....
48 INFORME DE SERVICIO ANOTE LAS FECHAS CUANDO HA HECHO EL SERVICIO NORMAL Cuando sea C a d a C a d a C a d a C a d a Ca d a necesario 8 h or as 25 horas 50 horas 100 horas 200 horas Cambiar el aceite del motor ........................................
49 6 DATI DI SERVIZIO COMPILARE OGNI QUALVOLTA SI ESEGUE UN REGOLARE SERVIZIO Necessità Ogni Ogni Ogni . Ogni Ogni 8 ore 25 ore 50 ore 100 ore 200 ore Cambio dell'olio .............................................................................
50 6 Blades For best results mower blades must be kept sharp. Replace bent or damaged blades. Sharpening can be carried out with a file or grinding disc. NOTE! It is very important that both blades are sharpened equally to avoid imbalance. BLADE REMOVAL: • Raise mower to highest position to allow access to blades.
51 6 Cuchillas Para alcanzar resultados mejores las cuchillas de la segadora hay que mantenerlos afilados. Sustituya las cuchillas torcidos y estropeados. El afilado puede hacerse con lima o muela. NOTA! Es muy importante que los dos lados de la cuchilla sean afilados igual a in de impedir desequilibrios.
52 6 1-1/2" Brakes The brakes are located inside the right rear wheel. The wheel should be dismantled for best access. • Press down the clutch/brake pedal and engage the parking brake. Bremse Die Bremse sitzt innerhalb des rechten Hinterrades. Für beste Zugänglichkeit ist das Rad auszubauen.
53 Dismantling of the cutting unit Work from the right side of the machine. 1. Take off the belt from the engine pulley (1). 2. Remove the small retainer spring (2) and lift clutch spring off the pulley bolt. 3. Remove the large retainer spring (3), slide collar off and push housing guide out of the bracket.
54 Assembly of the cutting unit • Push in the cutting unit under the machine. The ejector opening should be to the right. • Assemble in the reverse order to dismantling. Einbau des Mähdecks • Mähdecks unter den Traktor schieben. Die Auswurfoffnung muß nach rechts.
55 6 Replacement of drive belt for cutting unit 1. Dismantle the cutting unit as described previously. 2. Work off the belt from the unit's left pulley and then from the other wheels. 3. Pull the belt away from the cutting unit. 4. The new belt is mounted in the reverse order.
56 6 B A 1 2 Adjustment of the cutting unit A. In the direction of travel 1. Check that the air pressure is correct in all four tires. 2. Make sure that the machine is on a horizontal surface. 3. Lift up the cutting unit to its highest position. 4. Measure the distances A and B.
57 6 “A” REGLAGE TRANSVERSAL • Relever le carter de coupe dans sa position la plus haute. • Calculer la distance au sol à partir des milieux des bords extérieurs gauche et droite du carter de coupe. • La distance A doit être la mêne des deux côtés à 6 mm près.
58 6 Replacement of drive belt Dismantle the cutting unit as described previously Engage the parking brake and work off the belt upwards from the pulley (1), the clutch pulley (2) and the engine's drive wheel (3). Work off the belt upwards from the pulley at the rear axle (4).
59 6 EINSTELLUNG DES SCHALTHEBELS DES DIFFERENTIALGETRIEBES Das Differentialgetriebe muß sich in Leerlaufstellung befinden, wenn der Schalthebel in der Neutral-Stellung (N) (Verschlußsperre) steht. Diese Einstellung wird bereits vom Hersteller im Werk durchgeführt.
60 6 REGOLAZIONE DELLA LEVA DEL MECCANISMO DEL CAMBIO di velocità CON DIFFERENZIALE Il meccanismo del cambio con differenziale deve essere in posizione di folle quando la relativa leva è in posizione di folle (N) (blocco). Tale condizione viene impostata al momento della fabbricazione.
61 7. T roubleshooting. 7. Störungssuche. Engine will not start 1. No fuel in fuel tank. 2. Plug defective. 3. Plug connection defective. 4. Dirt in carburetor or fuel pipe. Start motor will not turn engine 1. Battery flat. 2. Poor contact between cable and battery pole.
62 7. Recherche des pannes. 7. Búsqueda de averías. Le moteur ne démarre pas 1. Manque d’essence dans le réservoir. 2. Bougie d’allumage défectueuse. 3. Raccord de bougie défectueux. 4. Impuretés dans le carburateur ou la canalisation de carburant Le démarreur n’entraîne pas le moteur 1.
63 7. Ricerca guasti. 7. Het localiseren van fouten. Il motore non parte 1. Manca il carburante. 2. Difetto di candela. 3. Collegamento della candela difettoso. 4. Sporco nel sistema di alimentazione e o nel carburatore. Il motorino di avviamento non fa girare il motore 1.
64 The following steps should be taken when mowing season is over: • Clean the entire machine, especially underneath the cutting unit cover. • Touch up all chipped paint surfaces in order to avoid corrosion. • Change engine oil. • Drain the fuel tank.
65 8. Rismessaggio. 8. Stallen. Al termine della stagione effettuare i seguenti interventi: • Pulire tutto il tagliaerba e particolarmente sotto il coper- chio della falciatrice. • Ritoccare danni alla verniciatura per evitare ossidazione. • Cambiare l’olio del motore.
66.
67.
532 18 25-21 1.10.02 rad Printed in U.S.A..
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Husqvarna YT155 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Husqvarna YT155 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Husqvarna YT155 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Husqvarna YT155 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Husqvarna YT155, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Husqvarna YT155.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Husqvarna YT155. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Husqvarna YT155 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
