Manuale d’uso / di manutenzione del prodotto 175 del fabbricante Husqvarna
Vai alla pagina of 40
E E E E n n n n g g g g l l l l i i i i s s s s h h h h Rider 175 Rider 175 A WD Oper ator ′ s manual Please r ead the operator’ s manual carefull y and make sur e you understand the instructions before using the machine.
2 – English CONTENTS Contents CONTENTS Contents ...................................................................... 2 Ser vice journal Pre-deliv er y ser vice ..................................................... 3 After the first 8 hours ......
English – 3 Ser vice journal Pre-deliver y service 1 1a. Dry-charged battery (506788801) Fill the batter y with batter y acid and charge for 4 hours at max. 6 amp. 1b. Wet-charged battery (510138501) Charge the batter y for 4 hours at max. 3 amp. 2 Fit steering wheel, seat and any optional equipment.
4 – English INTR ODUCTION Dear Customer , Thank y ou f or choosing a Husqvarna Rider . Husqvarna Riders are built to a unique design with a front-mounted cutting unit and a patented rear-wheel steering system. Riders are designed for maximum efficiency e ven in small or confined areas.
English – 5 INTR ODUCTION Good ser vice Husqv arna products are sold all over the world and only through servicing dealers. This is to ensure that you, the customer , get the best suppor t and ser vice. For e xample, bef ore this machine was deliv ered it was inspected and adjusted b y your dealer .
6 – English KEY T O SYMBOLS Symbols These symbols are on the machine and in the instr uctions. W ARNING! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine .
English – 7 KEY T O SYMBOLS Chec k the engine’ s oil lev el Check tr ansmission oil lev el Lift up the cutting unit Apply the parking brake . If the engine is cold, use the choke Release the parki.
8 – English SAFETY INSTR UCTIONS Saf ety instructions These instr uctions are f or your saf ety . Read them carefully . Insure y our Rider • Check the insur ance cov erage f or your ne w Rider.
English – 9 SAFETY INSTR UCTIONS • Ne ver allo w children or other persons not trained in the use of the machine to use or ser vice it. Local laws ma y regulate the age of the user . • Use hearing protection to minimise the r isk of hearing impairment.
10 – English SAFETY INSTR UCTIONS • When mowing, k eep aw a y from bushes and other objects . • Follo w the manuf acturer’ s recommendations regarding wheel weights or counterbalance weights to increase machine stability .
English – 11 SAFETY INSTR UCTIONS • Make sure all nuts and bolts are tightened correctly and that the equipment is in good condition. • Do not modify safety equipment.
12 – English WHA T IS WHA T? Location of the contr ols 3 4 5 91 1 1 2 6 21 13 10 8 7 1 Throttle control/choke control 2 Ignition lock 3 Cutting height adjustment le ver 4 Lifting le ver f or the cutting unit 5 Speed limiter f or rev ersing 6 Speed limiter f or driving forward 7 P arking brake 8 Lock b utton f or parking brake 9 Seat adjustment.
English – 13 PRESENT A TION Presentation Cong ratulations on y our choice of an e xcellent quality product that will give y ou great pleasure for man y years . This operator’ s manual describes Rider 175 and Rider 175 A WD . The machines are equipped with a 17,5 horse power engine from Briggs & Stratton.
14 – English PRESENT A TION Lifting le ver f or the cutting unit The lift le ver is used to set the cutting unit in tr anspor t or mowing position. If the le ver is pulled bac kwards the unit is r aised and the blades automatically stop rotating (tr anspor t position).
English – 15 PRESENT A TION Release le ver The release control must be pulled out in order f or the machine to be mov ed when the engine is shutoff . Should you attempt to driv e the machine with the clutch controls pulled out it will not mov e. The drive on the axle is disengaged when one of the controls is pulled out.
16 – English Driving Bef ore star ting • Read the safety instructions and inf ormation concer ning the placement of controls and functions bef ore star ting. • P erf orm daily maintenance before star ting as set out in the Maintenance schedule. Start the engine 1 Make sure that the clutch control is depressed.
English – 17 Driving 5 When the engine star ts release the ignition ke y immediately back to neutr al position. 6 Push the throttle control to full throttle position. Let the engine run at moderate speed or half throttle for 3-5 minutes bef ore subjecting it to heavy load.
18 – English Driving Driving the Rider 1 Release the parking brake b y first pressing down the parking brake pedal and then releasing it. 2 Carefully press down one of the pedals until the required speed is obtained. P edal (1) is used to drive f orwards, and pedal (2) to drive bac kwards.
English – 19 Driving Stop the engine Pref erably allo w the engine to idle f or a minute to obtain normal wor king temperature bef ore stopping it if it has been working hard. Av oid idling the engine for long periods, as there is a risk of carbon build-up on the spark plugs.
20 – English Maintenance Maintenance sc hedule The f ollowing is a list of the maintenance which should be conducted on the machine. For those points not described in this manual, visit an authorised ser vice workshop. 1) First change after 5 hours.
English – 21 Maintenance Cleaning Clean the machine directly after use. It is much easier to wash off grass cuttings bef ore they dr y . Oily dir t can be remov ed using a cold degreasing agent. Spra y on a thin la yer . Rinse at normal water pressure.
22 – English Maintenance Chec king and adjusting the steering wires The steering is controlled by means of wires. These can in time become slack, which implies that the adjustment of the steering becomes altered. Check and adjust the steering as f ollows: 1 Remov e the frame plate b y loosening the two scre ws.
English – 23 Maintenance 2 Loosen the locking n uts (1). 3 T ension the cable using the adjuster screw (2) until the pla y in the cable is tak en up . 4 Tighten the locking n uts (1). 5 The brak e should be check ed again after adjustment 6 Assemble the left-hand wing co ver .
24 – English Maintenance Replacing the air filter If the engine seems to lack po wer or does not run smoothly this ma y be because the air filter is clogged. It is therefore impor tant to replace the air filter at regular inter vals (see Maintenance/Maintenance Schedule f or the correct ser vice inter val).
English – 25 Maintenance Chec king the fuel pump’ s air filter Check regularly that the fuel pump’ s air filter is free from dir t. The filter can when necessar y be cleaned with a brush. Contr olling the acid level in a dry- char ged battery Check that the le vel of the battery acid lies between the markings.
26 – English Maintenance Chec k the safety system The machine is equipped with a saf ety system that pre vents star ting or driving under the following conditions . The engine should only be possible to start when the cutting unit is in its raised position and the h ydrostat pedals are in the neutral position.
English – 27 Maintenance Main fuse The main fuse is placed in a detachable holder under the batter y case’ s cover , in front of the batter y . T ype: Flat pin, 15 A. Do not use any other type of fuse when replacing. A blo wn fuse is indicated by a b urnt connector .
28 – English Maintenance Make sure that the tongue (3) on the cutting unit engages correctly . 3 Inser t the bolt and secure it with a locking pin. 4 Press down the frame and insert the pin. Fit the dr ive belt around the drive wheels of the cutting unit.
English – 29 Maintenance Remo ving the cutting unit 1 Carr y out points 1-9 to put the cutting unit in the ser vice position, see Ser vice position f or the cutting unit.
30 – English Maintenance Replacing the cutting unit belts On these cutting units with collision-proof blades , the blades are driven b y one V -belt. Do as f ollows to change the V -belt: 1 Remov e the cutting unit. 2 Undo the bolt on the lift strut and the two screws on the cov er .
English – 31 Maintenance 5 Disengage the spring for the drive belt tensioning wheel. Rider 175 Rider 175 A WD 6 Place a f oot on the front edge of the cutting unit near the wheel and raise the front edge of the unit to mak e it easier to remov e the lift strut.
32 – English Maintenance Chec king the blades T o achiev e the best mowing results it is important that the blades are undamaged and w ell-shar pened. Check that the b lades’ attachment screws are tight. The blades should be balanced after sharpening.
English – 33 Lubrication Chec king the engine’ s oil level. Check the oil le vel in the engine when the Rider stands horizontal with the engine s witched off. Open the engine cov er . Loosen the dipstick, pull it up and wipe it off . Now insert the dipstick again.
34 – English Lubrication Changing the oil filter The oil filter must be replaced after e v er y 200 hours running time. T urn the old oil filter anti-clockwise to remov e. If necessar y , use a filter remov er . Lightly lubricate the r ubber seal on the ne w oil filter using new oil.
English – 35 T roub leshooting schedule Prob lem Procedure Engine does not start There is no fuel in the fuel tank Spark plug def ective F aulty spark plug connections or interchanged cab les Dir t .
36 – English Storage Winter stora ge At the end of the season, or if the machine is going to stand idle f or more than 30 days , it should immediately be made ready f or storage. Fuel which is left to stand for long periods (30 da ys or more) can leav e tacky deposits which can b lock the carburettor and interf ere with the engine.
English – 37 T echnical data 1) As rated b y the engine manuf acturer Rider 175 Rider 175 A WD Dimensions Length without cutting unit, mm/ft 2020/6,61 2020/6,61 Width without cutting unit, mm/ft 880.
38 – English T echnical data ´®z+R?T¶6&¨ ´®z+R?T¶6&¨ EC-dec laration of conf ormity (Applies to Eur ope only) Husqvarna AB, SE-561 82 Huskv ar na, Sweden, tel.
.
´®z+R?T¶6&¨ 2009-06-02 ´®z+R?T¶6&¨ 1150315-26.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Husqvarna 175 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Husqvarna 175 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Husqvarna 175 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Husqvarna 175 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Husqvarna 175, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Husqvarna 175.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Husqvarna 175. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Husqvarna 175 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
