Manuale d’uso / di manutenzione del prodotto 43045 del fabbricante Hunter Fan
Vai alla pagina of 18
43045-01 10/15/2009 1 Installation Guide Energy Star Bath Fan Models 82043 READ and SA VE THESE INSTRUCTIONS ENGLISH See page 2 ESp añoL V ea la página 19.
43045-01 10/15/2009 2 1) Read all instructions before attempting to install or use this appliance. This appliance is for general ventilating use only .
43045-01 10/15/2009 3 6) Never place a switch where it can be reached from a tub or shower . Do not install this appliance in a tub or shower enclosure. 7) Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction codes and standards.
43045-01 10/15/2009 4 F G I L M x2 N x6 * * A B C 98141-01-000 03242-07-133 98142-01-000 x2 D 97134-01-000 74508-03-133 Housing Wiring Co ver F an Assembly 3/8” Cable Connector Light F ixture Wiring Co ver Screw Check all the parts. If damag ed , call 1-888-830-1326 for replacement.
43045-01 10/15/2009 5 Loosen the wiring cover screw . Remove the fan assembly from the housing. Remove the wiring cover . D E C Choose Installation Option For New Construction - attaching to joist, go to step A1, page 5. For New Construction - suspended between, joists go to step B1, page 7.
43045-01 10/15/2009 6 A 1 Section A - New Construction - attaching to joist Drive mounting screws (supplied) into joist or framing. Position the correct depth mark at the bottom edge of the joist based upon the the thickness of your sheetrock. 5/8 1/2 5/8 1/2 A 2 Pop out a wiring access slug.
43045-01 10/15/2009 7 A 6 Connect 6” duct and vent to the outside. Use duct tape to secure joints. If ducting does not fit securely , an adapter may need to be purchased. Vaya a la sección E – Instalación Final en la página 14. Section B - New Construction – suspended between joists Pop out a wiring access slug.
43045-01 10/15/2009 8 Mark position of screws by using holes as a template. Drill a pilot hole at the TOP of each outline. B4 1/16” bit B5 Insert mounting screws, leaving space between the screw head and the joist. (Screws are supplied.) Attach the rails onto the screws.
43045-01 10/15/2009 9 B10 Install the wiring and the strain relief into the wiring access hole you made earlier . B11 Connect 6” duct and vent to the outside. Use duct tape to secure joints. If ducting does not fit securely , an adapter may need to be purchased.
43045-01 10/15/2009 10 Slide the mounting rails into brackets. C3 5/8 1/2 5/8 1/2 C4 Using the depth markings on the housing, position the bottom edge of the housing so that it will be flush with the sheetrock. Pop out a wiring access slug. C6 C5 Mark position of screws by using holes as a template.
43045-01 10/15/2009 1 1 C7 Insert mounting screws, leaving space between the screw head and the joist. (Screws are supplied.) Attach the rails onto the screws. C8 C9 Tighten screws. 3” C 1 0 Run the power supply wire through the strain relief, leaving 3” between the end of the wire and the strain relief.
43045-01 10/15/2009 12 Vaya a la sección E – Instalación Final en la página 14. Section D - Existing Construction – accessible from below Remove one of the wiring access slugs on the top of the housing. Use a second wiring access plug if needed.
43045-01 10/15/2009 13 Connect 6” duct and vent to the outside. Use duct tape to secure joints. If ducting does not fit securely , an adapter may need to be purchased. Install the wiring and the strain relief into the wiring access hole you made earlier .
43045-01 10/15/2009 14 E2 E 3 Connect fan wiring harness. DO NOT ALLOW THE F AN TO HANG FROM THE WIRING HARNESS. INST ALLA TION IS EASIER IF TWO PEOPLE ARE INVOL VED. Install the wiring cover box. Make sure all wiring connec- tions are inside the wiring cover box.
43045-01 10/15/2009 15 E5 Secure the fan assembly by tightening the two fan mounting screws. E7 Install the strain relief bracket. DO NOT ALLOW THE LIGHT FIXTURE TO HANG FROM THE WIRING HARNESS. INST ALLA TION IS EASIER IF TWO PEOPLE ARE INVOL VED. E8 E6 E6 E7 Remove thumbnuts.
43045-01 10/15/2009 16 E15 Complete. E9 E13 Install light bulb cover . Restore power at the source. E11 E12 Secure the fan assembly by tightening the two fan mounting thumbnuts.
43045-01 10/15/2009 17 T rouble Shooting Problem: Fan does not come on. Solution: • T urn power on, replace fuse, or reset breaker. • Hunter Fan Bath V entilators are extremely quiet. T o conrm that the fan is running, place your hand near the vents to feel the air movement.
43045-01 10/15/2009 18 Hunter Fan Company Bath Fan LIMITED W ARRANTY Hunter Fan Company makes the following limited warranty to the original user or consumer purchaser of this Hunter Bath Fan: If any .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Hunter Fan 43045 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Hunter Fan 43045 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Hunter Fan 43045 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Hunter Fan 43045 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Hunter Fan 43045, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Hunter Fan 43045.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Hunter Fan 43045. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Hunter Fan 43045 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
