Manuale d’uso / di manutenzione del prodotto 43042-01 del fabbricante Hunter Fan
Vai alla pagina of 21
43042-01 02/21/2008 1 FRANÇAIS Consulter la page 45 ENGLISH See page 2 ESP AÑOL V ea la p á gina 23 82048 T urino Bath V entilator with Light READ and SA VE THESE INSTRUCTIONS Installation Guide.
43042-01 02/21/2008 2 TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: PREVENT A TIVE MAINTENANCE A clean fan provides better service. Disconnect the power supply and clean the fan as listed below . TO CLEAN GRILLE: Use a mild detergent, such as dishwashing liquid, and a soft cloth.
43042-01 02/21/2008 3 D 95044-01-000 N 75184-01-133 L 97959-01-000 K 65219-01-000 J 77521-01-000 E 95029-01-000 A x4 F 75191-01-000 G 03242-07-133 I H 74508-03-133 98037-01-000 x2 O 97960-01-000 M 75729-01-000 P 77535-01-000 Check all the parts. If damaged, call 1-888-830-1326 for replacements.
43042-01 02/21/2008 4 Remove the motor/blower from the housing. Remove the pre-loaded screw tip covers. Back out the pre-loaded screw tips until flush with the side of the housing. Remove packing material. T urn off the power source. Before Installation Loosen screws.
43042-01 02/21/2008 5 7 G Pop out the first wiring access slug. Use second if needed. Insert the strain relief into the housing and secure with the washer .
43042-01 02/21/2008 6 5/8 1/2 A1 1 A13 A12 E Connect wires as shown. Pull wires through the strain relief. Position the correct depth mark at the bottom edge of the joist based on the thickness of your sheetrock. New Construction – attaching to joist Screw pre-loaded screws into joist or framing.
43042-01 02/21/2008 7 0 0 0 0 0 0 0 0 0 A15 A18 A20 A19 A17 A16 F H I G E Connect wiring from the motor to the wiring cover plate. Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing.
43042-01 02/21/2008 8 5/8 1/2 5/8 1/2 1/8" Bit Slide the mounting rails into brackets. Mark position of screws by using holes as a template. New Construction – suspended between joists Position the correct depth mark at the bottom edge of the joist based on the thickness of your sheetrock.
43042-01 02/21/2008 9 Connect wires as shown. T ighten screws. Pull wires through the strain relief. Insert screws, leaving space between the screw head and the joist.
43042-01 02/21/2008 10 Connect wiring from the motor to the wiring cover plate. Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing. T urn on the power source. Secure the motor by tightening the 2 screws.
43042-01 02/21/2008 11 8” 8.5” B26 C1 1 C12 B27 E1 Go to step on page 18 to attach grille. Existing Construction – accessible from above OR Remove an existing fan and check to make sure the opening is large enough to accommodate the new motor housing (8”x 8.
43042-01 02/21/2008 12 1/8" Bit 5/8 1/2 5/8 1/2 C13 C14 C15 C16 C17 C18 Drill a hole in the center of each outline. Insert screws, leaving space between the screw head and the joist. Screws are not provided. Attach the rails onto the screws. T ighten screws.
43042-01 02/21/2008 13 C19 C20 C21 T ighten the strain relief screws. Connect 4” duct and vent to the outside. T ape joints. If ducting does not fit securely , an adapter may need to be purchased. Pull wires through the strain relief. Connect wires as shown.
43042-01 02/21/2008 14 Secure the motor by tightening the 2 screws. T urn on the power source. T est the motor . If the motor does not run, check the plug connection. Install the wiring cover plate. Make sure all wiring connections are inside the box or under the wiring cover plate.
43042-01 02/21/2008 15 2 1 Existing Construction – accessible only from below Pull wires through strain relief . Remove an existing fan and check to make sure the opening is large enough to accommodate the new motor housing (8”x 8.5”). Move the housing into position above the ceiling.
43042-01 02/21/2008 16 D15 E D16 D17 D18 F G F H A Fan Motor Light 2 Pin Black Ground Green Bare Copper White Black Main Switch 1 (AC In) Black Switch 2 (AC In) Black Light *Option White White 3 Pin *Option Fan & Main Light T ogether Connect wiring from the motor to the wiring cover plate.
43042-01 02/21/2008 17 D19 D20 H I D21 D22 D23 E1 Go to step on page 18 to attach grille. T est the motor . If the motor does not run, check the plug con- nection. T urn on the power source. Reinstall the motor by inserting the tabs and pushing up into position.
43042-01 02/21/2008 18 E1 E3 E4 E5 E6 E2 K K J L Align posts A, B, C and D (stamped into motor housing) with posts A, B, C and D (stamped into light fixture). Slide light fixture over posts. Remove the strain relief bracket screw . Position the strain relief bracket under the motor as shown.
43042-01 02/21/2008 19 Align glass dome and push up. Screw glass stop into position. Screw Finial into position Complete. Attach thumbscrews. W ARNING: T o reduce the risk of electrical shock, all 4 thumbscrews MUST be properly installed. Install 2 Max 60 W att A15 bulbs (Not Included).
43042-01 02/21/2008 20 T rouble Shooting Problem: Fan does not come on. Solution: • Hunter Fan Bath V entilators are extremely quiet. T o conrm that the fan is running, place your hand near the vents to feel the air movement. • T urn power on, replace fuse, or reset breaker .
43042-01 02/21/2008 21 W arranty © 2008 Hunter Fan Company Hunter Fan Company Bath Exhaust Fan LIMITED W ARRANTY Hunter Fan Company makes the following limited warranty to the original user or consum.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Hunter Fan 43042-01 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Hunter Fan 43042-01 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Hunter Fan 43042-01 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Hunter Fan 43042-01 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Hunter Fan 43042-01, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Hunter Fan 43042-01.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Hunter Fan 43042-01. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Hunter Fan 43042-01 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
