Manuale d’uso / di manutenzione del prodotto HDR600 del fabbricante Humminbird
Vai alla pagina of 16
Thank you for choosing Humminbird, America’s #1 name in depthsounders. Humminbird has built its reputation by designing and manufacturing top - quality, thoroughly reliable marine equipment. Your Humminbird is designed for trouble - free use in even the har shest marine environment.
Transom Mounting Inside The Hull Mounting Installing the HDR 600 Testing the Installation Section 3: USING THE HDR 600 What You See On Screen Control Functions Section 5: MAINTENANCE AND WARRANTY Main.
GENERAL INFORMATION TRANSDUCER EXCHANGE As the HDR 600 transducer receives sonar signals, it converts them to a digital depth that is displayed on your HDR 600.
INSTALLATION PARTS SUPPLIED Before installing your HDR 600, please ensure thet the following parts are included in the box: • HDR 600 Depth sounder • Transducer with 20 feet of cable • Transduce.
Determining the Proper Location Follow the steps below if you are mounting t he transducer on the transom. As a boat moves through the water, turbulence is generated by the weight of he boat, and the thrust of the propeller(s).
horizontal lines on the template. If not, tilt the template slightly so that the lower edge of the transom falls within the allowable range. Using a pencil or punch, mark the three mounting holes onto the transom. Using a 5/32” bit, drill the three holes to a depth of approximately 1”.
Assembling the Transducer Body Attach the Pivot to the tra nsducer body, as shown in the illustration below, using the two ¼’ - 20 x 5/8” machine screws, toothed washers, and square nuts. The toothed washers must fit on the inside of the transducer ears.
Installing The Transducer Body To The Boat Slide the assembled transducer into the metal bracket from the bottom, alignin g the large hole at the top of the bracket with the hole in the pivot. Insert the pin the pivot holes in the bracket and pivot. The headed pin can be inserted from either side of the bracket.
The screw has a thread - locking compound on the threads to prevent loosening, and should not be fully tightened until a ll adjustments are made. Adjusting The Running Position Of The Transducer The running position of the transducer is now completely adjustable.
Note: On some hulls, it may be necessary to angle the transducer so that the back end is ¼” lower than the front. Next, adjust the height of the assembly so the face of the transducer is 1/8” to ¼” beneath the bottom of the transom, and fully tighten the three mounting screws.
Inside the boat there is often a channel or conduit used for other wiring, which can be used to route the transducer cable forward. The transducer cable should not be cut or shortened, and care sh ould be used not to damage the cable insulation.
Insert the HDR 600 from the front of the panel. Install the “U” bracket and wing nut from the rear of the panel ensuring that the face of the HDR 600 is rotated upright. If the panel into which you are mounting the unit is greater than ¼” thick, the “U” bracket may appear too long.
CAUTION: Some boats have 24 or 36 - volt electric systems. Be sure your HDR 600 i s connected to a 12 VDC power supply. If you must wire the HDR 600 directly to a battery, be sure to install an in - line fuse holder and one amp fuse (not included), for the protection of the unit.
When in an active function, a single press to an arrow button will result in a single incremental adjustme nt. Pressing and holding an arrow button will sequence through a range of adjustments. If no adjustment is made for 5 seconds, the unit will return to normal operation.
After your selection is made, the unit will return to normal operation after 5 seconds. The selected units icon should now be visible as shown in figure 8.
2. There is no bottom reading visible on the display. There are a number of possible causes for this condition. If the loss of bottom information occurs only at high speeds, then a transducer adjustment is needed.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Humminbird HDR600 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Humminbird HDR600 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Humminbird HDR600 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Humminbird HDR600 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Humminbird HDR600, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Humminbird HDR600.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Humminbird HDR600. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Humminbird HDR600 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
