Manuale d’uso / di manutenzione del prodotto M671111 del fabbricante Huffy
Vai alla pagina of 25
1 07/05 ID# M671111 © COPYRIGHT 2005 by HUFFY SPORTS Toll-Free Customer Service Number for U.S: 1-800-558-5234, For Canada: 1-800-284-8339 , For Europe: 00 800 555 85234 (Sweden: 009 555 85234 ), For Australia: 1-800-333 061 Internet Address: http://www.
2 ID# M671111 07/05 BEFORE YOU ST ART! T o ensure optimal playability of backboard system, a close tolerance fit between the elevator component s and hardware is required. T est-fit large bolt s into large holes of elevator tubes, backboard bracket s, and triangle plates.
07/05 ID# M671111 3 Owner must ensure that all players know and follow these rules for safe operation of the system. W ARNING • DO NOT HANG on the rim or any part of the system including backboard, support braces or net.
4 ID# M671111 07/05 SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system.
07/05 ID# M671111 5 IMPORT ANT! Remove all content s from boxes. Be sure to check inside pole sections; hardware and additional p arts are p acked inside. NOTICE T O ASSEMBLERS ALL Huffy Sport s Basketball Systems, including those used for DISPLA YS, MUST be assembled and ballasted with sand or water according to the instructions.
6 ID# M671111 07/05 Get to know the basic parts of your basketball system..... FRONT P ANEL BACKBOARD FRONT RIM BASE POLE.
07/05 ID# M671111 7 P ARTS LIST - (See Hardware Identifier) Item Qty. Part No. Description 1 1 203470 Washer, Flat, 1.5” O.D. 2 1 806620 Base Assembly 3 1 804833 Exacta Height Assembly 4 1 908006 To.
8 ID# M671111 07/05 HARDW ARE IDENTIFIER (BOL TS & SCREWS) * You may have extra parts with this model. #7 (2) #40 (1) #39 (2) Item #23 (1) #29 (6) #16 (2) #12 (1) #44 (4)* #19 (4) #47 (4) #49 (1) .
07/05 ID# M671111 9 HARDW ARE IDENTIFIER (NUTS & W ASHERS) HARDW ARE IDENTIFIER (PLASTIC SP ACERS CAPS & CLIPS) HARDW ARE IDENTIFIER (OTHER) #13 (2) #20 (2) #26 (4) #30 (4) #36 (2) #1 1(4)* #1.
10 ID# M671111 07/05 T OOLS REQUIRED FOR THIS SECTION SECTION A: ASSEMBLE THE BASE And/Or: This is what your system will look like when you’ve finished this section: 1/2” 9/16” Wrenches (2) 1/2.
07/05 ID# M671111 11 1A. Check the following pre-assembled base areas for tightness: Eye bolt s P/N 203452, W asher P/N 203218 , Nut P/N 203100, Carriage Bolts P/N 203223 .
12 ID# M671111 07/05 Check the following pre-assembled handle areas for tightness: Screw P/N 204803, Nut P/N 203100, Carriage Bolt s P/N 203103 . Carriage Bolt P/N 203103 Nut P/N 203100 Nut P/N 203100.
07/05 ID# M671111 13 6 5 4 3. WOOD SCRAP (NOT SUPPLIED) 5 4 While maintaining alignment, bounce middle pole section (5) into top section (4) using a wood scrap as shown until the top pole no longer moves toward the pole identification sticker on the middle pole.
14 ID# M671111 07/05 4. 4 5 6 WOOD SCRAP (NOT SUPPLIED) RODS SHOWN ARE FOR VISUAL REPRESENTATION OF ALIGNMENT AND ARE NOT SUPPLIED WITH THE HARDWARE TROUGH TROUGH TROUGH Align dimple of middle pole section (5) into trough of bottom pole section (6) as shown.
07/05 ID# M671111 15 9 7 6 9 7 13 8 45 5. Install bolt (12) through bracket and bottom pole section (6) and secure with nut (10) as shown. Nut should be tightened until flush (even) with locknuts outer edge. 12 10 6 7. Secure cover to rod (9) using washers (45) nuts (8) and nut covers (13) as shown.
16 ID# M671111 07/05 8 . Install pole mount bracket (15) and reinforcement bracket (42) with carriage bolt s (16) as shown. T ighten flange nuts (14) completely . 4 42 14 14 15 16 16 9. Att ach sp acers (20, 21) to pole mount bracket (15) with bolts (19), washers (17), and nuts (8) as shown.
07/05 ID# M671111 17 Assemble lanyard (25) to locking pin (24) as shown (FIG A). Attach covers (22) onto pole mount bracket (15) with carriage bolt (23) and nut (14) as shown. 10 . 15 14 24 22 22 25 23 FIG . A 25 24 Loop end of pin lanyard (25) over carriage bolt (23) as it p asses through the pole mount bracket (15) during this assembly .
18 ID# M671111 07/05 TOOLS REQUIRED FOR THIS SECTION SECTION B: A TT ACH THE BACKBOARD Phillip s- Head Screwdriver This is what your system will look like when you’ve finished this section: W renche.
07/05 ID# M671111 19 Assemble backboard brackets (27) using bolt s (43), and nuts (8) as shown. 1. 27 43 8 8 43.
20 ID# M671111 07/05 2. Attach lower elevator tubes (32) and counter balance springs (33) to backboard support brackets (27) using sp acers (26), bolt (29), and nut (31) as shown.
07/05 ID# M671111 21 3. 50 52 1 48 49 Inst all Slam Jam Rim to Backboard 34 51 49 1 52 A B C D E A Fit rim (34) securely into bracket (48) as shown. Allow T -bolt (49) to slip through center hole in rim (34). B Install reinforcement bracket (50) onto T -bolt (49) as shown.
22 ID# M671111 07/05 4. Attach upper elevator tubes (35) to backboard support bracket s (27) using spacers (26 & 1 1), bolt (29), and nut (31) as shown.
07/05 ID# M671111 23 31 31 40 38 32 4 37 37 29 30 32 30 29 32 29 35 30 31 31 35 30 37 36 36 5. Support pole on sawhorse. Attach backboard assembly to top pole section (4) as shown. Install pole cap (38). Use caution; elevator assembly is heavy . 6. 7.
24 ID# M671111 07/05 8. Insert bolt (29) through left side upper elevator tube (35), then stretch spring (33) onto bolt (29). Insert bolt (29) through right side upper elevator tube (35) and secure with nut (31). 9. Roll completed assembly to desired position.
07/05 ID# M671111 25 1. Apply height adjustment and moving label (46) to front of pole as shown. 2. A. While holding handle, remove pin (24). B. Move elevator up or down to desired height. C. Replace pin (24) full length to lock system at desired height.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Huffy M671111 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Huffy M671111 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Huffy M671111 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Huffy M671111 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Huffy M671111, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Huffy M671111.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Huffy M671111. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Huffy M671111 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
