Manuale d’uso / di manutenzione del prodotto 89225 del fabbricante Huffy
Vai alla pagina of 20
1 P/N 21154401 01/04 IMPORT ANT! T o ensure prompt and correct handling of any problems, or to answer any questions, please contact the Sample and Display T echnician at 1-800-558-5234.
P/N 21154401 01/04 2 BEFORE YOU ST ART! T o ensure optimal playability of backboard system, a close tolerance fit between the elevator component s and hardware is required. T est fit large bolts into large holes of elevator tubes, backboard bracket s and triangle plates.
3 P/N 21154401 01/04 IMPORT ANT! Remove all content s from boxes. Be sure to check inside pole sections; hardware and additional p art s are packed inside. NOTICE T O ASSEMBLERS AL L Huffy Sport s Basketball Systems, including those used for DISPLA YS, MUST be assembled and ballasted with sand or water according to the instructions.
P/N 21154401 01/04 4 P A R TS LIST (See Hardware Identifier) Item Qty. Part No. Description 1 2 900033 Back Bracket 2 2 203796 T-Bolt, 3/8-16 x 5 3 2 200318 Bracket 4 2 203472 Spring 5 2 201651 Spacer, .50 I.D. x .25 Long 6 2 206303 Washer, 1/4" Flat 7 8* 203113 Bolt, Hex-Flange 5/16-18 x 2.
5 P/N 21154401 01/04 Item #33 (12) Item #30 (4) Item #40 (4) HARDW ARE IDENTIFIER (BOL TS & SCREWS) Item #67 (2) PLASTIC SP ACERS Item #7 (10) Item #4 (2) Item #22 (2) Item #13 (2) Item #27 (5) It.
P/N 21154401 01/04 6 Install display boards in the marked locations. Each mounting location consist s of a mounting pole stub with the following dimensions: Height = 8”, O.D. = 3 3/8”, I.D. = 3 1/8” (arrows indicate direction the board is facing).
7 P/N 21154401 01/04 At corner locations 1, 2, and 3 install the display pole to the mounting pole stub. If required, secure the display pole by sliding the display wedge (12) into position as shown. T o lock the display pole in place, tighten the set screw (13 or 39).
P/N 21154401 01/04 8 8 11 49 16 1. 2. 17 30 24 52 51 49 30 3. 49 8 55 54 54 57 44 57 55 4. 48 8 46 45 26 47 25 Install pole mount bracket (49) with carriage bolts (16) as shown. T ighten flange nuts (8) completely . Attach sp acers (51, 52) to pole mount bracket (49) with bolts (24), washers (30), and nuts (17) as shown.
9 P/N 21154401 01/04 STEEL FRAME A CR YLIC BACKBOARD ASSEMBL Y - Corner Location 1 37 5. 38 38 24 24 17 17 Attach backboard support brackets (37) to the backboard frame using bolts (24), spacers (38), and nuts (17) as shown . 29 29 39 39 59 37 42 Refer T o Instructions Included With Rim Hardware For Rim Assembly .
P/N 21154401 01/04 10 7. 21 21 27 59 37 42 59 Attach upper elevator tubes (21) to backboard support bracket s (37) using spacers (59), bolt (27), and nut (42) as shown. 8. Attach backboard assembly to pole section (1 1). Install pole cap (43). 42 21 43 21 29 29 27 27 USE CAUTION; ELEVATOR ASSEMBLY IS HEAVY.
11 P/N 21154401 01/04 10. 9. Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05m) mark with pin (55). Attach adjustment rod (47) to lower elevator tubes (29) using bolt (27) spacer (59) and nut (42) as shown.
P/N 21154401 01/04 12 3 35 22 4 58 1 2 • Fit rim (58) securely into bracket (1) as shown. • Install reinforcement bracket (3) onto “T” bolt (2) as shown. • Install spring (4) onto “T” bolt (2) as shown. • Install special nut (35) and washer (22) onto “T” bolt (2).
13 P/N 21154401 01/04 44” F AN MOLDED PLASTIC BOARD ASSEMBL Y - Corner Location 2 Correctly identify each pole section. ONL Y THE T OP POLE SECTION (14) IS USED IN THIS ASSEMBL Y . 1. BOTTOM POLE 43” MIDDLE POLE 43” TOP POLE 31” 14 Fit spacer (15) into p awl (19).
P/N 21154401 01/04 14 Assemble elevator tubes (21) to ratchet (28) and backboard brackets (23) using bolt s (20), spacers (5, & 40), and nut s (42) as shown. T ighten completely . 5 . Secure pawl (19) in place with clevis pin (31) and washers (6) as shown.
15 P/N 21154401 01/04 7. Insert “T” bolt (2) through Slam Jam bracket (1) as shown. Secure Slam Jam bracket (1) and backboard bracket (23) assemblies to backboard. Bend upper halves of backboard brackets (23) to line up with holes in backboard and secure with bolts (44 & 7) and nut s (8).
P/N 21154401 01/04 16 20 20 41 9. Attach upper and lower elevator tubes (21) to top pole section (14) using bolt s (20) and nuts (42) as shown. Attach pole cap (41) as shown. 42 21 21 21 21 • Fit rim (58) securely into bracket (1) as shown. • Install reinforcement bracket (3) onto “T” bolt (2) as shown.
17 P/N 21154401 01/04 Correctly identify each pole section. Poles have an identification sticker that will be used as a reference point in the next step. ONL Y THE T OP POLE SECTION (50) IS USED IN THIS ASSEMBL Y . F AN MOLDED PLASTIC BOARD ASSEMBL Y - Corner Location 3.
P/N 21154401 01/04 18 F AN BACKBOARD ASSEMBL Y - Corner Location 4. TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY. WARNING Assemble fan backboard as shown below with a standard rim as shown. 33 32 33 8 65 7 33 1.
19 P/N 21154401 01/04 Install net clip s. CLIP “ARM” CLIP “BODY” Insert one “arm” of clip into ram as shown. T wist “body” of clip slightly so that second “arm” slides over the top of the first “arm” as shown. Push in direction indicated by arrows.
P/N 21154401 01/04 20 Install net. Insert net into bottom of clip as shown. SIDE VIEW T wist net until it snaps into position. Net must be centered through clip.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Huffy 89225 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Huffy 89225 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Huffy 89225 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Huffy 89225 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Huffy 89225, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Huffy 89225.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Huffy 89225. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Huffy 89225 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
