Manuale d’uso / di manutenzione del prodotto U5361950 del fabbricante Hoover
Vai alla pagina of 14
HOOVER ® Thank you for your pur chase! Bagless Upright ® This product was designed for easy assembly (see page 3) www .hoover .com ENGLISH ➜ pp. 1-14 ESP AÑOL ➜ pág.
2 Thank you for choosing a HOOVER ® pr oduct. Please enter the COMPLETE model and serial numbers in the spaces provided. The numbers are located on the bottom of your cleaner . Model_________________________________________ Serial number_________________________________________ Hint: Attach your sales receipt to this owner’s manual.
3 1. Cleaner Assembly If you need any assistance: V isit our website at www .hoover .com . Click on the “Service” button to find the service outlet near est you OR Call 1-800-944-9200 for an automated r eferral of service outlet locations (U.S. only) OR Call 1-330-499-9499 to speak with a r epr esentative in our Consumer Response Center .
C 4 Align end of hose with projections (A) over slots (B) in dirt duct. Slide hose into duct (B) and twist hose to lock it into place. Snap ends of dusting brush (A), crevice tool (B) and furniture nozzle (C) into clips as shown. 1-10 1-5 1-8 1-6 1-7 1-9 1-12 Place nuts in recessed ar eas on front of handle.
5 Continued ➜ 1. Handle 2. Cord hooks: wrap cord around hooks for storage. The top hook rotates right or left for easy cord release. 3. Hose 4. ON/OFF switch: located on left rear corner of cleaner body 5. Carrying handle 6. Stair cleaning handle: located on lower edge of dirt cup.
Handle position For ease in sliding knob, place handle in the upright position (C). The nozzle will not move into the adjusted position until the cleaner handle is lowered to the operating position (D). Settings For maximum cleaning performance, the following carpet height settings are recommended.
7 Edge cleaning Edge cleaning is provided on both sides of the nozzle to remove dirt in carpet near baseboards and furniture. Guide either side of nozzle parallel to edge of carpet or furniture. Cleaning tools T ools allow for cleaning surfaces above the floor and for reaching har d to clean areas.
3. Maintenance When to empty It is recommended that the dirt cup be emptied before the dirt reaches the dirt opening on back of dirt cup (Fig. 3-1) or after every use if preferred. CAUTION: V ery fine materials, such as face powder or cornstarch, may seal the filter and cause loss of suc- tion.
9 3-10 3-6 3-5 3-7 3-8 3-9 3-11 Pull up on pre-filter assembly . Slide it out of cup. Replace dirt cup. Filter assembly How to clean filter assembly Remove dirt cup and dir t cup lid as described in “How to empty dirt cup”. Pivot pre-filter assembly towar d center of cup.
G Remove lens - Disconnect clean- er from electrical outlet. Using a screwdriver , remove the two screws as shown and lift of f lens. 3-16 3-15 10 Secondar y and final filters Cleaning secondary filter Disconnect cleaner from electrical outlet.
11 Continued ➜ 3-17 3-18 Remove agitator brush roll Remove agitator and used belt. Discard used belt. Replace lens - Reposition lens and secure with the two scr ews. How to replace Disconnect cleaner from electrical outlet. Remove bottom plate Place handle in low position and turn cleaner over so bottom side is up.
12 3-24 3-25 The agitator brush roll When to replace When agitator brushes are worn, the agitator should be replaced. T o check condition of brushes, discon- nect cleaner from electrical outlet. Move edge of a card acr oss bottom plate while turning agitator .
D 13 Clearing blockages Disconnect cleaner from electrical outlet. Low suction or pick up may be due to a blockage in the system. Refer to the fol- lowing steps to check for blockages continuing with each step until the blockage is found: T urn cleaner OFF and disconnect from electrical outlet.
14 Full One Y ear W arranty (Domestic Use) Y our HOOVER ® appliance is warranted in normal household use, in accordance with the Owner’ s Manual against original defects in material and workmanship for a period of one full year from date of purchase.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Hoover U5361950 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Hoover U5361950 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Hoover U5361950 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Hoover U5361950 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Hoover U5361950, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Hoover U5361950.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Hoover U5361950. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Hoover U5361950 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
