Manuale d’uso / di manutenzione del prodotto 1250G del fabbricante Honeywell
Vai alla pagina of 240
™ Voyager TM 1250g Single-Line Laser Scanner User’s Guide.
Disc laimer Honeyw ell International Inc. (“HII”) reser v es the right to mak e changes in speci- fications and other inf ormation contained in this document without prior notice, and the reader should in all cases cons ult HII to deter mine whether an y such changes hav e been made .
1 Chapter 1 - Getting Started About This Manual ............. ......................................... 1-1 Unpacking Your Device ...... ......................................... 1-1 Connecting the Device ..............................................
2 Verifone ® Ruby Terminal Default Settings .................. 2-9 Gilbarco ® Terminal Default Settings ............................ 2-9 Honeywell Bioptic Aux Port Configuration ................. 2-10 Datalogic™ Magellan © Bioptic Aux Port Configuration .
3 Scanner-Bioptic Packet Mode ............................. 2-28 ACK/NAK ............................................................. 2-28 Communication Timeout ..................................... 2-28 Chapter 3 - Input/Output Settings Power Up Beeper .
4 Deactivation Character ........................................ 3-15 Reread Delay .......................... ................................... 3-16 User-Specified Reread Delay .................................... 3-16 Output Sequence Overview ....
5 Other Programming Selections ............................. 5-3 Terminal ID Table ............... ......................................... 5-4 Data Format Editor Commands .................................. 5-4 Move Commands .........................
6 EAN-13 Beginning with 2 Addenda Required ...... 6-46 EAN-13 Beginning with 290 Addenda Required .. 6-47 EAN-13 Beginning with 378/379 Addenda Required .......... ............................... 6-47 EAN-13 Beginning with 414/419 Addenda Required ...
7 Chapter 9 - Serial Programming Commands Conventions ..................... ........................................... 9-1 Menu Command Syntax ....... ....................................... 9-1 Query Commands ........................................
8.
Pr oduct Agency Compliance USA FCC P art 15 Subpar t B Class B This de vice complies with par t 15 of th e FCC Rules. Oper ation is subject to the f ollowing two conditions: 1. This device may not caus e harmful interference. 2. This device must accept any interference received, including interference that may ca use undesired operation.
This product is intended to be supplie d by a Listed Direct Plug-In P ow er unit marked "Class 2" or "LPS" and rated 5 Vdc - 5.2 Vdc , 1A. Canada Industry Canada ICES-003 This Class B digital apparatus complie s with Canadian ICES-003.
This product has required the e xtraction and use of natural resources f or its production. It ma y contain hazardous su bstances that could impact health and the environment, if not properly disposed.
International Laser Safety Statement This de vice has been tested in acco rdance with and complies with IEC60825-1 ed2.0 and 21 CFR 1040.10 and 1040.11, except f or de viations pursuant to Laser Notice No . 50, dated June 24, 2007. LASER LIGHT , DO NO T ST ARE INT O BEAM, CLASS 2 LASER PROD- UCT , 1 mW MAX OUTPUT: 630-650nM.
Required Safety Label Locations Part Number, Serial Number Laser Label, and Revision Information location Laser Safety information Laser Output.
.
1 - 1 1 Getting Star ted About This Manual This User’ s Guide provides installati on and programming instructions f o r the V oy ager 1250g single-line lase r scanner. Product specifications , dimensions, warranty , and customer suppor t inf or mation are also included.
1 - 2 2. The scanner beeps. 3. Verify the scanner operation by scanning a bar code from the Sample Symbols in the back of this manual. The unit def a ults to a USB PC K eyboard. Refer to page 2-5 f or other USB terminal settings. F or additional USB programming and te chnical inf or mation, ref er to “USB Application Note, ” av ailable at www.
1 - 3 Connecting with RS232 Serial P or t 1. Turn off power to the terminal/computer. 2. Connect the appropriate inte rface cable to the scanner. 3. Plug the serial connector into th e serial port on your computer. Tighten the two screws to secu re the connector to the port.
1 - 4 Connecting with RS485 A scanner can be connected f o r an IBM POS terminal interface . 1. Connect the appropriate interface cable to the device, then to the com- puter. 2. Turn the terminal/computer po wer back on. The scanner beeps. 3. Verify the scanner operation by scanning a bar code from the Sample Symbols in the back of this man ual.
1 - 5 Reading T echniques The scanner has a view finder that proj ects a bright red ai ming beam that corre- sponds to the scanner’ s horizontal fiel d of view . The aiming beam should be centered horizontally ov er the bar code and must highlight all the vertical bars of the bar code.
1 - 6 When you have entered all the commands you want to save for your custom defaults, scan the Save Custom Defaults bar code. Y ou may ha ve a series of custom settings and want to correct a single setting. T o do so , just scan the new setting to o v erwrite the old one.
1 - 7 Resetting the F actory Defaults If you aren’t sure what prog ramming opti ons are in your scanner , or you’ve changed some options and w ant to restore the scanner to f actor y def ault set- tings, first scan the Remo ve Custom Defaults bar code, then scan Activate Defaults .
1 - 8.
2 - 1 2 Pr ogramming the Interface Intr oduction This chapter describes how to program y our system for the desired interf ace. Pr ogramming the Interface - Plug and Pla y Plug and Pla y bar codes pro vide in stant scanner set up for commonly used interf aces.
2 - 2 RS485 Scan one of the f ollowing “Plug and Pl a y” codes to program the scanner f or an IBM POS terminal interface. Note: After scanning one of these code s, you must power cycle the cash register.
2 - 3 OPOS Mode The f ollowing bar code configures y our scanner f or OPOS (OLE for Retail P oint of Sale) by modifying th e f ollowing OPOS-related settings: Option Setting Interf ace RS232 Baud Rate.
2 - 4 USB IBM SureP os Scan one of the f ollowing “Plug and Pl a y” codes to program the scanner f or an IBM SureP os (USB handheld scanner ) or IBM SureP os (USB tabletop scanner) interf ace. Note: After scanning one of these code s, you must power cycle the cash register.
2 - 5 USB PC or Macintosh Ke yboard Scan one of the f ollowing codes to progr am the scanner for USB PC K ey- board or USB Macintosh K eyboard. Scanning these code s also adds a CR and LF . USB HID Scan the f ollowing code to progr a m the scanner f or USB HID bar code scanners.
2 - 6 Scan the bar code below , then set th e length for the HID F allback (from 0- 60 minutes) b y scanning digits from the Programming Chart , then scanning Save . Def ault = 5 minutes. USB Serial Commands USB Serial Emulation Scan one of the f ollowing codes to pr ogram the scanner to em ulate a regu- lar RS232-based COM P or t.
2 - 7 A CK/NAK Mode Communication Timeout This allows y ou to set the length (in milliseconds) for a timeout f or the host A CK/NAK response. Scan the bar code belo w , then set the timeout (from 0-65535 milliseconds) by sc anning digits from the Programming Chart , then scanning Save .
2 - 8 Comm unication Timeout Beeper This selection programs the scanner to issue an error beep when a communication timeout has occurred . The error beep sound is pro- grammed using Number of Beeps – Error (page 3-4). Def ault = On. NAK Retries This selection limits the number of N AK retries that can occur in ACK/NAK mode.
2 - 9 V erifone ® Rub y T erminal Default Settings Scan the f ollowing Plug and Pla y code to program the scanner f or a V eri f one Ruby terminal. This bar code sets th e baud rate to 1200 bps and the data f or- mat to 8 data bits, Mark parity , 1 stop bit and RTS/CTS no timeout.
2 - 10 Honeywell Bioptic A ux P or t Configuration Scan the f o llo wing Plug and Play code to program the scanner f or a Honeywell bioptic scanner auxiliar y port configuration. This bar code sets the baud rate to 38400 bps and the data f o rmat to 8 data bits, no parity , 1 stop bit.
2 - 11 Wincor Nixdorf T erminal Default Settings Scan the f ollowing Plug and Pla y code to program the scanner f or a Wincor Nix- dorf terminal. This bar co de sets the baud r ate to 960 0 bps and the data f or mat to 8 data bits, no parity , 1 stop bit.
2 - 12 Ke yboard Country La yout Scan the appropriate countr y code below to prog ram the keyboard la yout f or your country or language. As a general rule, the f ollowing characters are sup- por ted,.
2 - 13 Ke yboard Country (continued) Ref er to the Honeyw ell website ( www.honeywell.com/aidc) f or complete key- board countr y support information and app licable interf aces.
2 - 14 Ke yboard W edg e Modifier s AL T Mode If your bar code contains special char acters from the e xtended ASCII char t f or e xample, an e with an accent gr av e (è), you will use AL T Mode. (See Extended ASCII Characters on page A-5.) Note: Scan the ALT mode bar code after scanning th e appropriate Keyboard Country code.
2 - 15 Shift Lock is used when you normally hav e the Shift Lock k ey on (not com- mon to U .S. ke yboards). A utocaps via NumLock bar code should be scan ned in countries (e.g., Germany , F rance) where the Caps Lock ke y cannot be used to toggle Caps Lock.
2 - 16 Def ault = K eyboard Conv ersion Off . Ke yboard Modifier s This modifies special ke yboard feat ures, such as CTRL+ ASCII codes and T urbo Mode. Control + ASCII Mode On: The scanner sends k ey combinations f or ASCII control characters f or values 00-1 F (ref er to the ASCII char t f or Non- Printable Characters , page A-4).
2 - 17 Def a ult = Control + ASCII Mode Off . Numeric Ke ypad Mode: Sends numeric characters as if entered from a numeric ke ypad. Def a ult = Off. Inter -Scan Code Dela y When your k eyboard detects .
2 - 18 <F0> Break Character When your k eyboard detects that any k ey is being pressed, released, or held down, the k eyboard sends a pack e t of inf or mation kno wn as a “scan code” to your computer . There ar e two different types of scan codes: “make codes” and “break codes .
2 - 19 RS232 Modifiers RS232 Baud Rate Baud Rate sends the data from the scann er to the ter minal at the specified rate. The host terminal must be set f o r the same baud rate as the scanner .
2 - 20 RS232 W ord Length: Data Bits, Stop Bits, and P arity Data Bits sets the word length at 7 or 8 bi ts of data per character . If an application requires only ASCII Hex char acters 0 th rough 7F decimal (text, digits, and punctuation), se lect 7 data bits.
2 - 21 RS232 Handshaking RS232 Handshaking allows control of data transmission from the scanner using software commands from the host de vice. When R TS/CTS is turned Off , no data flow control is used. Flow Contr ol, No Timeout: The scanner asser ts R TS when it has data to send, and will wait indefinitely f o r CTS to be asser ted by the host.
2 - 22 and CTS is not asser ted, the de vice tran smit buff er is cleared and scanning ma y resume. Def ault = R TS/CTS Off . RS232 Timeout When using Flow Control with Timeout, y ou must program the length of the dela y you w ant to wait for CTS from the host.
2 - 23 data transmission stops. T o resume transmission, the host sends the XON character (DC1, he x 11). Data transm ission continues where it left off when XOFF was sent. Def ault = XON/XOFF Off . A CK/NAK After transmitting data, the scanner wait s for an ACK character (hex 06) or a NAK character (hex 15) response from the host.
2 - 24 number of retries (from 0-255) by scanning digits from the Programming Chart , then scanning Save . (5 is the recommended set- ting.) Def a ult = 0. Comm unication Timeout Beeper This selection programs the scanner to issue an error beep when a communication timeout has occurred .
2 - 25 Support BEL/CAN in ACK/NAK This protocol responds to <BEL > and <CAN> commands when in ACK/ NAK mode. The scanner sounds an error tone when a <BEL> command is sent from the host. <CAN> terminates the transmission. Default = BEL/ CAN Off .
2 - 26 Bloc k Check Character When this selection is set to T ransmit , the NCR Block Check Char acter (BCC) is e xpected with incoming me ssages and transmitted with outgoing messages. Def ault = T ransmit. NCR Prefix This selection allows y ou to program an NCR-specific prefix.
2 - 27 NCR Prefix/Suffix When set to T ransmit , both the NCR prefix and suffix are transmitted with bar codes. Usually , prefixes and su ffix es are programmed using the Data Editing selections (see Data Editing beginning on page 4-1), how e ver , the f ollowing commands ov erride any other prefix/suffix settings.
2 - 28 Scanner -Bioptic P acket Mode Pa cke t M od e O n m ust be scanned to set the sc anner’ s format so it is com- patible with a bioptic scanner . Def a ult = P acket Mode Off . A CK/NAK After transmitting data, the scanner waits for an ACK character (hex 06) or a NAK character (hex 15) response fr om the host.
3 - 1 3 Input/Output Settings P ower Up Beeper The scanner can be programmed to beep when it’ s powered up . Scan the Off bar code(s) if you don’t w ant a power up beep . Def ault = P ower Up Beeper On - Scanner . Beep on BEL Character Y ou may wish to f orce the scanner to beep upon a command sent from the host.
3 - 2 Good Read and Err or Indicators Beeper – Good Read The beeper ma y be programmed On or Off in response to a good read. T ur ning this option off , only tur ns o ff the beeper response to a good read indication. All error and me nu beeps are still audible .
3 - 3 Beeper Pitch – Good Read The beeper pitch codes modify the pitc h (frequency) of the beep the scan- ner emits on a good read. Def ault = Medium. Beeper - T ransmit Order The beeper transmit order determines when the good read beep occurs. The scanner can be set to emit the go od read beep either bef ore or after data transmission.
3 - 4 Beeper Duration – Good Read The beeper duration codes modify the length of the beep the scanner emits on a good read. Def ault = Normal. Number of Beeps – Good Read The number of beeps of a good read can be progr ammed from 1 - 9. The same number of beeps will be applied to the beep er and LED in response to a good read.
3 - 5 T o change the number of error beeps , scan the bar code belo w and then scan a digit (1-9) bar code and the Save bar code on the Programming Chart inside the back cover of this manual.
3 - 6 LED Indicators The green and red LEDs can be progr amm ed to be On or Off and at different brightness lev els to indicate various scanner states. Use the f ollowing bar codes to program the LED indicators . LED Settings Def ault = Red LED Off with Laser, Green LED On with Good Scan.
3 - 7 LED Brightness Def a ult = Red High, Green High. In-Stand and Out-Of-Stand Settings The f o llo wing settings program the scanner’ s behavior when it is either in the stand, or out of the stand (hand-held).
3 - 8 Caution: When working with In-Stand and Out-of-Stand settings, enable the settings you want before di sabling those you do not want to use. If you disable settings fi rst, you may program the scanner so it is unable to read bar code s. if this happens, power cycle the scanner and scan the defaults bar code on page 1-6 .
3 - 9 Presentation Mode with CodeGate® Out-of-Stand: When the scanner is not in the stand, it automaticall y detects bar codes and decodes them. Howe ver , the data is not transmitted un til you press the button. The laser remains on briefly after the transmission.
3 - 10 good read. If you scan Do Not End Manual Activ ation After Good Read , the laser remains on after a good read , but the b utton must be pressed to scan the ne xt bar code.
3 - 11 CodeGate ® When CodeGate is On , the button is used to allo w decoded data to be transmitted to the host system. Th e scanner remains on, scanning and decoding bar codes, b ut the bar code dat a is not transmitted until the button is pressed. W hen CodeGate is Off , bar code data is tr ansmitted when it is decoded.
3 - 12 End Object Detection After Good Read After a bar code is successfully detec ted and read from the scanner , the laser can be programmed either to remain on and scanning, or to turn off. When End Object Detection After Good Read is enabled, the laser turns off and stops scanning afte r a good read.
3 - 13 Object Detection Distance When the scanner is in the stand and you are using Object Detection Mode, y o u can set the distance r ange for detecting objects. Short sets the scanner to detect objects appro ximatel y 5 inches (12.7cm) aw ay from the nose.
3 - 14 ger scanning. Scan the ba r code below, then use the Programming Chart to read the alphanumeric combination that represents that ASCII character.
3 - 15 Character Deactiv ation Mode If you ha ve sent a character from the host to trigger the scanner to begin scan- ning, you can also send a deactiv ation ch aracter to stop scanning.
3 - 16 Reread Dela y This sets the time period bef ore the scanner can read the same bar code a sec- ond time. Setting a reread dela y protec ts against accidental rereads of the same bar code. Longer dela ys are effectiv e in minimizing accidental rereads.
3 - 17 Output Sequence Editor This programming selection allo ws yo u to program the scanner to output data (when scanning more than one sym bol) in whatev er order your appli- cation requires, regardle ss of the order in which the bar codes are scanned.
3 - 18 Output Sequence Example In this e xample, y ou are scanning Code 93, Code 128, and Code 39 bar codes, b ut you want the scanner to ou tput Code 39 1st, C ode 128 2nd, and Code 93 3rd, as shown belo w . Note: Code 93 must be enabl ed to use this example.
3 - 19 SEQBLK sequence editor star t command 62 code identifier f or Code 39 0012 A - Code 39 sample length (11) plus CR suffix (1) = 12 41 star t char acter match for Code 39, 41h = “A” FF termin.
3 - 20 Sequence Match Beeper By def a ult, the scanner beeps when a sequence match is f ound. If you want the scanner to remain silent, scan the Sequence Match Beeper Off bar code below .
3 - 21 When the output sequence is Off , the bar code data is output to the host as the scanner decodes it. Def ault = Off . No Read With No Read turned On , the scanner notifies y ou if a code cannot be read. If using an EZConfig-Scanning T ool Scan Data Window (see page 8-2 ), an “NR” appears when a code cannot be read.
3 - 22.
4 - 1 4 Data Editing Prefix/Suffix Overview When a bar code is scanned, additional in fo rmation is sent to the host computer along with the bar code data. This gr oup of bar code data and additional, user-defined data is called a “message stri ng. ” The selections in this section are used to build the user-defined data into the message string.
4 - 2 symbology to which you want to apply the prefix or suffix. For example, for Code 128, Code ID is “j” and Hex ID is “6A”. Step 3. Scan the 2 hex digits from the Programming Chart inside the back cover of this manual or scan 9 , 9 for all symbologies.
4 - 3 Step 1. Scan the Clear One Prefix or Clear One Suffix symbol. Step 2. Determine the 2 digit Hex val ue from the Symbology Chart (included in the Symbology Chart, beginning on page A-1) for the symbology from which you want to clear the prefix or suffix.
4 - 4 Suffix Selections T ransmit Alternate Extended ASCII Characters Y ou may need to emulate special k eyboa rd functions, such as up or do wn arrows , Alt/Make or Alt/Break command s , that are not suppor ted in the Extended ASCII Character tab le.
4 - 5 Alternate Extended ASCII Characters DEC HEX Ke yboard Function DEC HEX Keyboard Function 128 80 up arrow ↑ 152 98 F9 129 81 down arrow ↓ 153 99 F10 130 82 right arrow → 154 9A F1 1 131 83 .
4 - 6 Function Code T ransmit When this selection is enabled and f unction codes are contained within the scanned data, the scanner transmits the func tion code to the terminal. Char ts of these function c odes are provided in Supported Interface Keys star ting on page 7-2 .
4 - 7 Inter character , Interfunction, and Intermessage Dela ys Some terminals drop information (characters ) if data comes through too quickly . Intercharacter , interfunction, and intermes sage delays slow the transmission of data, increasing data integrity .
4 - 8 Ne xt, scan the Character to T rigger Delay bar code, then the 2-digit he x value f or the ASCII character that will trigger the delay ASCII Conversion Chart (Code Page 1252) on page A-4. T o remov e this delay , scan the Delay Length bar code, and set the number of dela ys to 0.
4 - 9 Intermessage Delay An intermessage delay of up to 5000 milliseconds (in 5ms increments) ma y be placed between each scan transmission. Scan the Intermessage Delay bar code belo w , then scan the number of 5ms delays , and the Save bar code using the Programming Chart inside the back co ver of this man- ual.
4 - 10.
5 - 1 5 Data Formatting Data Format Editor Intr oduction Y ou may use the Data F or mat Editor to change the scanner’ s output. F or e xam- ple, y ou can use the Data F or mat Editor to inser t characters at certain points in bar code data as it is scanned.
5 - 2 you are programming. (See Primary/Alternate Data Formats on page 5-10 for further information.) Step 3. Terminal Type Refer to Terminal ID Table (page 5-4) and loca te the Terminal ID number for your PC. Scan th ree numeric bar codes on the Programming Chart to program the scanner fo r your terminal ID (you must enter 3 digits).
5 - 3 Other Pr ogramming Selections Clear One Data Format This deletes one data format for one symbology. If you are clearing the primary format, scan 0 from the Programming Chart inside the back cover of this manual. If you are cl earing an alternate format, scan 1 , 2 , or 3 , depending on the format you are cl earing.
5 - 4 Data Format Editor Commands Send Commands Send all character s F1 Include in the output message all of the characters from the input message, starting from current cursor position, followed by an insert character. Syntax = F1xx where xx stands for the insert character’s hex value for its ASCII code.
5 - 5 Send all character s up to a particular character F3 Include in the output message all characters from the input message, starting with the character at the current cursor posi tion and continuing to, but not including, the search char acter “ss,” followed by an insert character.
5 - 6 Move the cur sor to the beginning F7 Move the cursor to the first character in the input message. Syntax = F7. Move the cur sor to the end EA Move the cursor to the last ch aracter in the input message.
5 - 7 Searc h forward f or a non-matching character E6 Search the input message forward fo r the first non-“xx” character from the current cursor positi on, leaving the cursor pointing to the non-“xx” character. Syntax = E6xx where xx stands for the search character’s hex value for its ASCII code.
5 - 8 Compare character s FE Compare the character in the current cursor position to the character “xx.” If characters are equal, move the cursor forward one position. Syntax = FExx where xx stands for the comparison character’s hex value for its ASCII code.
5 - 9 Data Formatter On, Not Required, Drop Prefix/Suffix Scanned data is modified according to y our data format. If a data format is found for a particular symbol, those prefixes and suffixes are not transmitted.
5 - 10 will sound. If you wish to hear t he error tone when a non-matching bar code is f o und, scan the Data Format Non-Matc h Error T one On bar code. Def ault = Data F ormat Non-Match Error T one On . Primary/Alternate Data Formats Y ou can save up to f our data formats, a nd s witch between these formats.
5 - 11 Fo r e xample, y ou may hav e set your de vi ce to the data format you sav ed as Data Fo rmat 3. Y ou can switch to Data F or mat 1 f or a single button press by scanning the Single Scan-Data Format 1 bar code belo w . The next bar code that is scanned uses Data F ormat 1, then rev er ts bac k to Data Format 3.
5 - 12.
6 - 1 6 Symbologies This programming section contains the f ollowing menu selections. Ref er to Chapter 9 f or settings and def aults. All Symbologies If you w a nt to decode all the symbologi es allo wable f or your scanner , scan the All Symbologies On code.
6 - 2 Message Length Description Y ou are able to set the valid reading le ngth of some of the bar code symbolo- gies. If the data length of the scanne d bar code doesn’t match the v alid read- ing length, the scanner will issue an error tone.
6 - 3 Codabar <Default All Codabar Settings> Codabar On/Off Codabar Start / Stop Characters Star t/Stop characters identify the leadi ng and trailing ends of the bar code . Y ou may either transmit, or not tr ansmit Star t/Stop characters. Def a ult = Don’t T ransmit .
6 - 4 When Check Character is set to V alidate, but Don’t T ransmit , the unit will only read Codabar ba r codes printed with a check char acter , but will not transmit the chec k character with the scanned data. Codabar Concatenation Codabar suppor ts symbol concatenati on.
6 - 5 Select Require to pre vent the scanner from decoding a single “D” Codabar symbol without its companion. This selection has no effect on Codabar symbols without Stop/Star t D characters . Concatenation Timeout When searching f or bar codes during concatenation, you ma y wish to set a dela y used to find the ne xt ba r code.
6 - 6 Codabar Message Length Scan the bar codes below to change the message length. Ref er to Message Length Description (page 6-2) f o r additional inf orm ation.
6 - 7 Code 39 < Default All Code 39 Settings > Code 39 On/Off Code 39 Start / Stop Characters Star t/Stop characters identify the leadi ng and trailing ends of the bar code . Y ou may either transmit, or not tr ansmit Star t/Stop characters. Def ault = Don’t T ransmit.
6 - 8 When Check Char acter is set to V alidate and T ransmit , the scanner only reads Code 39 bar codes printed with a check character , and will transmit this character at the end of the scanned data.
6 - 9 Code 32 Pharmaceutical (P ARAF) Code 32 Pharmaceutical is a form of the Code 39 symbology used by Ital- ian pharmacies. This symbol ogy is also known as P ARAF . Full ASCII If Full ASCII Code 39 dec oding is enabled, certai n character pairs within the bar code symbol will be inter preted as a single char acter.
6 - 10 Character pairs /M and /N decode as a minus sign and period respectiv ely . Character pairs /P through /Y decode as 0 through 9. * Full ASCII Off Full ASCII On.
6 - 11 Interleaved 2 of 5 < Default All Interleaved 2 of 5 Settings > Interleaved 2 of 5 On/Off Follett Formatting NULL Characters Interleave d 2 of 5 requires an ev en number of characters . When an odd number of characters is present, it is due to NULL char acters embedded in the bar code.
6 - 12 Check Digit No Check Digit indicates that the scanner reads and transmits bar code data with or without a check digit. When Check Digit is set to V alidate, but Don’t T ransmit , the unit only reads Interleave d 2 of 5 bar codes prin ted with a check digit, but will not transmit the chec k digit with the scanned data.
6 - 13 Interleaved 2 of 5 Messa g e Length Scan the bar codes below to chang e the message length. Ref er to Message Length Description (page 6-2) f or addition al inf ormation. Mini- mum and Maximum lengths = 1-80. Minim um Default = 6, Maxim u m Def a ult = 80.
6 - 14 When Check Digit is set to V alidate and T ransmit , the scanner only reads NEC 2 of 5 bar codes printed with a chec k digit, and will transmit this digit at the end of the scanned data.
6 - 15 Code 93 < Default All Code 93 Settings > Code 93 On/Off Code 93 Redundancy If you are encountering errors when reading Code 93 bar codes, y ou may want to adjust the redundancy count. Redundancy adjusts the nu mber of times a bar code is decoded bef o re tr ansmission, which ma y reduce the number of errors.
6 - 16 Code 93 Message Length Scan the bar codes below to change the message length. Ref er to Message Length Description (page 6-2) f o r additional inf orm ation.
6 - 17 scan a redundancy count between 0 and 10 on the Programming Chart inside the back co ver of this manual. Then scan the Save bar code. Def a ult = 0. Straight 2 of 5 Industrial Message Length Scan the bar codes below to chang e the message length.
6 - 18 Straight 2 of 5 IA T A (two-bar start/stop) Note: This symbology is also known as Airline Code 5. <Default All Straight 2 of 5 IATA Settings> Straight 2 of 5 IA T A On/Off Straight 2 of 5 IA T A Redundancy If you are encountering errors when re ading Straight 2 of 5 IA T A bar codes, you ma y want to adjust the redund ancy count.
6 - 19 Straight 2 of 5 IA T A Message Length Scan the bar codes below to chang e the message length. Ref er to Message Length Description (page 6-2) f or addition al inf ormation. Mini- mum and Maximum lengths = 1-80. Minim um Default = 13, Maxim um Def a ult = 15.
6 - 20 When Check Char acter is set to V alidate and T ransmit , the scanner only reads Matrix 2 of 5 bar codes printed wi th a chec k character , and will trans- mit this character at the end of the scanned data.
6 - 21 Code 11 <Default All Code 11 Settings> Code 11 On/Off Check Digits Required These options set whether 1 or 2 chec k digits are required with Code 11 bar codes. A uto Select Check Digits determines the number of check digits based on the length of the bar code.
6 - 22 Check Digit V alidation When Check Char acter is set to V alidate and T ransmit , the scanner will only read Code 11 bar code s printed with the specified type check charac- ter(s), and will transmit the characte r(s) at the end of the scanned data.
6 - 23 Code 11 Message Length Scan the bar codes below to chang e the message length. Ref er to Message Length Description (page 6-2) f or addition al inf ormation. Mini- mum and Maximum lengths = 1-80. Minim um Def a ult = 3, Maxim um Def a ult = 80.
6 - 24 Code 128 <Default All Code 128 Settings> Code 128 On/Off 128 Gr oup Separator Output If you wish to tr ansmit the group separa tor char acters “GS” (0x1D hex) with your Code 128 bar code output, scan the On bar code. When Off is scanned, the group separator is not output.
6 - 25 128 Redundancy bar code below , then scan a redundancy count between 0 and 10 on the Programming Chart inside the back co ver of this manual. Then scan the Save bar code. Def ault = 0. Code 128 Message Length Scan the bar codes below to chang e the message length.
6 - 26 Concatenation Timeout When searching f or bar codes during conc atenation, you ma y wish to set a dela y used to find the ne xt bar code. Set the length (in milliseconds) f or this dela y by sc.
6 - 27 ISBT 128 Predefined Concatenation Sequences On/ Off The f ollowing selections allo w you to en able or require the Predefined ISBT 128 Concatenation Sequences.
6 - 28 Step 1. Scan the 1st Left Identifier bar code, below. Step 2. Use the Programming Chart to scan 3, D (hex for “=”). Step 3. Scan Save . Step 4. Scan the 2nd Left Identifier bar code, below. Step 5. Use the Programming Chart to scan 4, 7 (hex for “G”).
6 - 29 If you scan the Require User -Defined Sequence code, the data combina- tion specified in the User-Defined co ncatenation sequence is required to transmit the data.
6 - 30 cation Number identifiers, only the fi rst ID character is remo ved from the Donation Identification Number . The second character is transmitted as normal data. Def ault = On. Flag Digit Con version T ype 3 flag digits are a par t of the Donation Identification Number in an ISBT 128 bar code.
6 - 31 GS1-128 <Default All GS1-128 Settings> GS1-128 On/Off GS1-128 Application Identifier P arsing This allows a single GS1-128 bar code to be brok en into multiple transmis- sions based on the presence of applicat ion identifiers (AI) embedded in the bar code.
6 - 32 128 Redundancy bar code below , then scan a redundancy count between 0 and 10 on the Programming Chart inside the back co ver of this manual. Then scan the Save bar code. Def ault = 0. GS1-128 Message Length Scan the bar codes below to change the message length.
6 - 33 Te l e p e n <Default All Telepen Settings> T elepen On/Off T elepen Output Using AIM T elepen Output, the scanner reads symbols with star t/stop pat- tern 1 and decodes them as standard full ASCII (start/stop patter n 1).
6 - 34 T elepen Redundancy bar code below , then scan a redundancy count between 0 and 10 on the Programming Chart inside the back co ver of this manual. Then scan the Save bar code. Def ault = 0. T elepen Message Length Scan the bar codes below to change the message length.
6 - 35 UPC-A <Default All UPC-A Settings> UPC-A On/Off UPC-A Number System and Check Digit UPC-A Number System The numeric system digit of a U .P .C . symbol is normally transmitted at the beginning of the sc anned data, but the can be progr ammed so it will not transmit it.
6 - 36 UPC-A Check Digit This selection allows y ou to specif y whether the check digit should be transmitted at the end of the scanned data or not. Def ault = On . UPC-A Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-A data. Def ault = Off f or both 2 Di git and 5 Digit Addenda.
6 - 37 Addenda Timeout Y ou can set a time dur ing which the scanner looks f or an addenda. If an addenda is not f ound within this time period, the data can be either trans- mitted or discarded, based on the setting you are using f or UPC-A Addenda Required (see page 6-36).
6 - 38 UPC-A/EAN-13 with Extended Coupon Code Use the f ollowing codes to enab le or disable UPC-A and EAN-13 with Extended Coupon Code. When left on the def ault setting ( Off ), the scanner treats Cou- pon Codes and Extended Coupon Codes as single bar codes.
6 - 39 Def a ult = Don’t Require Coupon Code . UPC-A Number System 5 Addenda Required This setting programs the scanner to require an y combin ation of a coupon code, a 2 digit addenda, or a 5 digi t addenda on UPC-A bar codes that begin with a “5.
6 - 40 Def ault = Don’t Require Coupon Code/Addenda. Addenda Timeout Y ou can set a time dur ing which the scanner looks f or a coupon code. If a coupon code is not f ound within this time period, t.
6 - 41 scanning the bar code below , then se tting the timeout (from 0-65535 milli- seconds) by scanning digits from the Programming Chart , then scanning Save . Def a ult = 100. Note: The Addenda Timeout setting is applied to all addenda and coupon code searches.
6 - 42 UPC-E0 Number System The numeric system digit of a UPC-A sy mbol is nor mally tr ansmitted at the beginning of scanned data. When us ing UPC-E Expand, the unit can be programmed so it will not tr ansmit it.
6 - 43 UPC-E0 Leading Zero This f e ature allo ws the transmission of a leading zero (0) at the beginning of scanned data. T o pr ev ent transmission, scan Off . Def ault = Off . UPC-E0 Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-E data.
6 - 44 Addenda Timeout Y ou can set a time dur ing which the scanner looks f or an addenda. If an addenda is not f o und within this time period, the data can be either trans- mitted or discarded, based on the setting you are using f or UPC-E0 Addenda Required (page 6-43).
6 - 45 EAN/J AN-13 <Default All EAN/JAN Settings> EAN/JAN-13 On/Off EAN/JAN-13 Chec k Digit This selection allows y ou to specif y whether the check digit should be transmitted at the end of the scanned data or not.
6 - 46 EAN/JA N-13 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data. Def ault = Off f or both 2 Digit and 5 Digit Addenda. EAN/JA N-13 Addenda Required When Required is scanned, the scanner wi ll only read EAN/JAN-13 bar codes that hav e addenda.
6 - 47 Don’t Require 2 Digit Addenda: If y ou hav e selected Require 2 Digit Addenda , and y ou want to disab le this feature, scan Don’t Require 2 Digit Addenda . EAN-13 bar codes ar e transmitted, depending on the setting you are using f or EAN/JAN-13 Addenda Required .
6 - 48 Require Addenda: All EAN-13 bar codes that beg in with a “378” or “379” must ha ve a 2 digit addenda, a 5 digi t addenda, or a combination of these addenda. The EAN-13 bar code with the addenda is then transmitted as a single, concatenated bar code .
6 - 49 Def a ult = Don’t Require Addenda. EAN-13 Beginning with 434/439 Addenda Required This setting programs the scanner to require an y combination of a 2 digit addenda or a 5 digit adde nda on EAN-13 bar codes t hat begin with a “434” or “439.
6 - 50 Def ault = Don’t Require Addenda. EAN-13 Beginning with 977 Addenda Required This setting programs the scanner to require a 2 digit addenda only on EAN-13 bar codes that begin with “977 .
6 - 51 Require 5 Digit Addenda: All EAN-13 bar codes t hat begin with “978” must hav e a 5 digit addendum. Th e EAN-13 bar code with the 5 digit addendum is then transmitted as a si ngle, concatenated bar code . If a 5 digit addendum is not f ound within the Addenda Timeout period, the EAN- 13 bar code is discarded.
6 - 52 Addenda Timeout Y ou can set a time dur ing which the scanner looks f or an addenda. If an addenda is not f o und within this time period, the data can be either trans- mitted or discarded, based on the setting you are using f or EAN/JAN-13 Addenda Required .
6 - 53 ISBN T ranslate ISBNs are printed on books using th e EAN-13 bar code symbology . T o translate EAN-13 Bookland symbols in to their equivalent ISBN n umber for- mat, scan the On bar code below .
6 - 54 ISSN T ranslate When On is scanned, EAN-13 977 Bookl and symbols are translated into their equivalent 8-digit ISSN n umber format. For e xample, 9770123456787 will be transmitted as 01234560.
6 - 55 EAN/J AN-8 <Default All EAN/JAN-8 Settings> EAN/JAN-8 On/Off EAN/JAN-8 Chec k Digit This selection allows y ou to specif y whether the check digit should be transmitted at the end of the scanned data or not.
6 - 56 EAN/JA N-8 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-8 data. Def ault = Off f or both 2 Di git and 5 Digit Addenda. EAN/JA N-8 Addenda Required When Required is scanned, the scanner wi ll only read EAN/JAN-8 bar codes that hav e addenda.
6 - 57 scanning the bar code below , then se tting the timeout (from 0-65535 milli- seconds) by scanning digits from the Programming Chart , then scanning Save . Def a ult = 100. Note: The Addenda Timeout setting is applied to all addenda and coupon code searches.
6 - 58 MSI <Default All MSI Settings> MSI On/Off MSI Chec k Character Diff erent types of check char acters are used with MSI bar codes. Y ou can program the scanner to read MSI bar codes with T ype 10 check charac- ters. Def a ult = V a lidate T ype 10, but Don’t T ransmit.
6 - 59 When Check Char acter is set to V alidate T ype 10/11, but Don’t T r ansmit , the unit will only read MSI bar codes printed with the specified type check character(s), b ut will not transmit th e chec k character(s) with the scanned data.
6 - 60 MSI Message Length Scan the bar codes below to change the message length. Ref er to Message Length Description (page 6-2) f o r additional inf orm ation.
6 - 61 When Check Char acter is set to V alidate and T ransmit , the scanner only reads Plessey bar codes printed with a check char acter , and will transmit this character at the end of the scanned data.
6 - 62 GS1 DataBar Omnidirectional < Default All GS1 DataBar Omnidirectional Settings > GS1 DataBar Omnidirectional On/Off GS1 DataBar Omnidirectional Redundancy If you are encountering errors when reading GS1 DataBar Omnidirectional bar codes, y ou may want to adjust the redundancy count.
6 - 63 GS1 DataBar Limited < Default All GS1 DataBar Limited Settings > GS1 DataBar Limited On/Off GS1 DataBar Limited Redundancy If you are encountering errors wh en reading GS1 DataBar Limited bar codes, y ou may want to adjust the redundancy count.
6 - 64 GS1 DataBar Expanded < Default All GS1 DataBar Expanded Settings > GS1 DataBar Expanded On/Off GS1 DataBar Expanded Redundancy If you are encountering errors when reading GS1 DataBar Expanded bar codes, y ou may want to adjust the redundancy count.
6 - 65 GS1 DataBar Expanded Message Length Scan the bar codes below to chang e the message length. Ref er to Message Length Description (page 6-2) f or addition al inf ormation. Mini- mum and Maximum lengths = 1-80. Minim um Def a ult = 3, Maxim um Def a ult = 80.
6 - 66 If EAN8 to EAN13 Con version is scanned, all EAN8 ba r codes are conv er ted to EAN13 f ormat. Def ault = GS1 Emulation Off . P ostal Codes The f ollowing lists linear postal codes . Any combination of linear postal code selections can be active at a time .
6 - 67 China P ost (Hong K ong 2 of 5) On/Off China P ost (Hong K ong 2 of 5) Redundancy If you are encountering errors when reading China P ost (Hong K ong 2 of 5) bar codes, y ou may want to adjust the redundancy count. Redun- dancy adjusts the number of times a bar code is decoded bef ore trans- mission, which ma y reduce the number of errors.
6 - 68.
7 - 1 7 Interface K e ys Ke yboard Function Relationships The f ollowing K eyboard Function Code , He x/ASCII V alue, and Full ASCII “CTRL ”+ relationships apply to all ter min als that can be used with the scanner . Ref er to page 2-16 enable Control + ASCII mode .
7 - 2 The last five char acters in the Full ASC II “CTRL ”+ column ( [ ] 6 - ), apply to US only . The following chart indicates th e equiv alents of these five characters f or different countries. Note: Not all countries may be supported by your device.
7 - 3 CR 0D CR/Enter RETURN SO 0E Inser t Ins Help SI 0F Escape ESC DLE 10 F11 F11 DC1 11 Home Home DC2 12 Print Prnt Scr n DC3 13 Back Space BA CKSP ACE DC4 14 Back T ab LSHIFT T AB NAK 15 F12 F12 SY.
7 - 4.
8 - 1 8 Utilities T o Add a T est Code I.D. Prefix to All Symbologies This selection allows y ou to tur n on transmission of a Code I.D . before the decoded symbology . (See the Symbology Chart, beginning on page A-1) f or the single character code th at identifies each symbology .
8 - 2 Te s t M e n u When you scan the T est Menu On code, then scan a programming code in this manual, the scanner displa ys the content of a programming code. The pro- gramming function will still occur , but in addition, the content of that program- ming code is output to the terminal.
8 - 3 item under the “Configure” tree node in the application explorer . When one of these tree nodes is click ed, the r ight-hand side is loaded with the parameters' f or m belonging to th at par ticular category . The Con- figure tree option has all the pr ogramming and configuration par ame- ters specified f or a scanner .
8 - 4.
9 - 1 9 Serial Pr ogramming Commands The serial programming commands can be used in place of the programming bar codes. Both the serial commands and the programming bar codes will pro- gram the scanner . For complete descriptions and examples of each serial pro- gramming command, ref er to the corres ponding programming bar code in this manual.
9 - 2 Storage A single character that specif ies the storage table to which the command is applied. An exclamation point ( ! ) performs the command’s operation on the device’s volatile menu configuration table. A period ( . ) performs the command’s operation on the device’s non-volatile menu configuration table.
9 - 3 Responses The de vice responds to serial co mmands with one of three responses: ACK Indicates a good command which has been processed. ENQ Indicates an invalid Tag or SubTag command. NAK Indicates the command was good, but the Data field entry was out of the allowable range for this Tag an d SubTag combination, e.
9 - 4 MAX60[ACK], DFT[ACK]. This response indicates that the de vice’ s Codabar Coding Enable (CBRENA) is set to 1, or on; the Star t/Stop Char acter (SSX) is set to 0, or Don’t T ransmit; the Che.
9 - 5 The char ts on the f ollowing pages list th e factory default settings f or each of the commands (indicated by an asterisk (*) on the programming pages).
9 - 6 Menu Commands Selection Setting * Indicates default Serial Command # Indicates a numeric entry Pag e Product Default Settings Setting Custom Def a ults Set Custom Def a ults MNUCDF 1-6 Sav e Cus.
9 - 7 Plug and Pla y Codes: USB USB K eyboard (PC) P AP124 2-5 USB K eyboard (Mac) PA P 1 2 5 2-5 USB Japanese K eyboard (PC) PA P 1 3 4 2-5 USB HID P AP131 2-5 HID F allback Mode HID F allback Mode (.
9 - 8 USB Serial Commands USB Serial Emulation f or Windows XP , Windows Server 2003, and later PA P 1 3 0 2-6 USB Serial Emulation f or Windows 2000 REMIFCO;P AP130 2-6 CTS/R TS Emulation On USBCTS1 .
9 - 9 Plug and Pla y Codes V erifone Rub y Te r m i n a l PA P R B Y 2-9 Gilbarco T er minal P APGLB 2-9 Honeyw ell Bioptic Au x Por t PA P B I O 2-10 Datalogic Magellan Bioptic A ux P or t PA P M A G.
9 - 10 Program K eyboard Countr y *U .S.A. KBDCTY0 2-12 Arabic KBDCTY91 2-12 Belgium KBDCTY1 2-12 Chinese KBDCTY92 2-12 Finland KBDCTY2 2-12 F rance KBDCTY3 2-12 Germany KBDCTY4 2-12 Hungar y KBDCTY19.
9 - 11 K eyboard Conv ersion *K eyboard Conv ersion Off KBDCNV0 2-16 Conv er t all Characters to Upper Case KBDCNV1 2-16 Conv er t all Characters to Low er Case KBDCNV1 2-16 K eyboard Modifiers *Contr.
9 - 12 RS-232 Modifiers RS232 Baud Rate 300 BPS 232BAD0 2-19 600 BPS 232BAD1 2-19 1200 BPS 232BAD2 2-19 2400 BPS 232BAD3 2-19 4800 BPS 232BAD4 2-19 *9600 BPS 232BAD5 2-19 19200 BPS 232BAD6 2-19 38400 .
9 - 13 W ord Length: Data Bits, Stop Bits , and Pa r it y 7 Data, 1 Stop , Pa r it y Ev en 232WRD3 2-20 7 Data, 1 Stop , P ar ity None 232WRD0 2-20 7 Data, 1 Stop , Pa r it y Od d 232WRD6 2-20 7 Data,.
9 - 14 RS232 Handshaking *R TS/CTS Off 232CTS0 2-22 Flow Control, No Timeout 232CTS1 2-22 Character-Based Flow Control, No Timeout 232CTS7 2-22 Two-Direction Flow Control 232CTS2 2-22 Flow Control wit.
9 - 15 NCR A CK/NAK *NCR ACK/NAK Off NCRACK0 2-25 NCR A CK/NAK On NCRA CK1 2-25 Block Chec k Character *T ransmit NCRBCC1 2-26 Don’t T ransmit NCRBCC0 2-26 NCR Prefix/Suffix NCR Prefix NCRPR2## 2-26.
9 - 16 Beeper Pitch - Good Read (F requency) Low (1600 Hz) BEPFQ11600 3-3 *Medium (2350 Hz) BEPFQ12350 3-3 High (4200 Hz) BEPFQ14200 3-3 Beeper - T ransmit Order *Bef ore Tr a n s m i s s i o n BEPWHN.
9 - 17 LED Settings *Red LED Off LEDFN10 3-6 Green LED Off LEDFN20 3-6 Red LED On with Good Scan LEDFN11 3-6 *Green LED On with Good Scan LEDFN21 3-6 Red LED On with Laser LEDFN12 3-6 Green LED On wit.
9 - 18 In-Stand and Out-of- Stand Settings In-Stand Def a ults AISDFT 3-8 Out-of-Stand Def a ults AO SD FT 3-8 Presentation Mode Out-of-Stand PA P P M 1 3-9 Presentation Mode with CodeGate Out- of-Sta.
9 - 19 In-Stand and Out-of- Stand Settings (continued) Laser Timeout - Button Release In- Stand (Range 1 - 65525) *0 ms AISMR T##### 3-10 Laser Timeout - Button Hold Out-of- Stand (Range 1 - 65525) *3.
9 - 20 In-Stand and Out-of- Stand Settings (continued) *End Object Detection After Good Read In-Stand AISOGD1 3-12 Do Not End Object Detection After Good Read Out-of- Stand AO SO GD 0 3-12 *End Object.
9 - 21 Character Activ ation Mode *Off HSTCEN0 3-13 On HSTCEN1 3-13 Activation Char acter HST ACH## 3-14 Do Not End Character Activ ation After Good Read HSTCGD0 3-14 *End Character Activation After G.
9 - 22 Require Output Sequence Required SEQ_EN2 3-21 On/Not Required SEQ_EN1 3-21 *Off SEQ_EN0 3-21 No Read On SHWNRD1 3-21 *Off SHWNRD0 3-21 Prefix/Suffix Selections Add CR Suffix to All Symbologies .
9 - 23 Interfunction Dela y Range 0 - 1000 (5ms increments) DL YFNC## 4-8 Intermessage Delay Range 0 - 1000 (5ms increments) DL YMSG## 4-9 Data Formatter Selections Data F ormat Editor *Default Data F.
9 - 24 Primar y/Alternate Data Fo rm ats Primar y Data Fo r ma t AL TFNM0 5-10 Data Format 1 AL TFNM1 5-10 Data Format 2 AL TFNM2 5-10 Data Format 3 AL TFNM3 5-10 Single Scan Data Fo rmat Change Singl.
9 - 25 Codabar Check Char . * No Check Char . CBRCK20 6-4 V alidate Modulo 16, But Don’t T ransmit CBRCK21 6-4 V alidate Modulo 16, and T ransmit CBRCK22 6-4 V alidate Modulo 7 CD , But Don’t Tr a.
9 - 26 Code 39 Check Char . * No Check Char . C39CK20 6-8 V alidate, But Don’t Tr a n s m i t C39CK21 6-8 V alidate, and T ransmit C39CK22 6-8 Code 39 Redundancy Range (0 - 10) *0 C39V O T## 6-8 Cod.
9 - 27 NEC 2 of 5 Def ault All NEC 2 of 5 Settings N25DFT 6-13 *Off N25ENA0 6-13 On N25ENA1 6-13 NEC 2 of 5 Check Digit * No Check Char . N25CK20 6-14 V alidate, But Don’t Tr a n s m i t N25CK21 6-1.
9 - 28 Straight 2 of 5 IA T A Default All Str aight 2 of 5 IA T A Settings A25DFT 6-18 Straight 2 of 5 IA T A *Off A25ENA0 6-18 On A25ENA1 6-18 Straight 2 of 5 IA T A Redundancy Range (0 - 10) *0 A25V.
9 - 29 Code 11 Check Digits Required 1 Check Digit Required C11CK20 6-21 *2 Check Digits Required C11CK21 6-21 A uto Select Check Digits Required C11CK22 6-21 Check Digit Va l i d a t i o n V alidate .
9 - 30 ISBT128 Predefined Concatenation Sequences * Donation ID Number (001) and ABO/RhD Blood Groups (002) ISBPCS0 6-26 Donation ID Number (001) and Donor ID Number (019) ISBPCS1 6-26 Donation ID Num.
9 - 31 ISBT 128 User- Defined Concatenation Sequences 1st Left Identifier (0- 255) *0 ISBUL1## 6-28 2nd Left Identifier (0- 255) *0 ISBUL2## 6-28 1st Right Identifier (0-255) *0 ISBUR1## 6-28 2nd Righ.
9 - 32 T elepen Def ault All T elepen Settings TELDFT 6-33 *Off TELENA0 6-33 On TELENA1 6-33 T elepen Output *AIM T e lepen Output TELOLD0 6-33 Original T elepen Output TELOLD1 6-33 T elepen Redundanc.
9 - 33 UPC-A/EAN-13 with Extended Coupon Code *Off CPNENA0 6-38 Allow Concatenation CPNENA1 6-38 Require Concatenation CPNENA2 6-38 UPC-A Number System 4 Addenda Required * Don’t Require Coupon Code.
9 - 34 UPC-E0 Expand *Off UPEEXP0 6-41 On UPEEXP1 6-41 UPC-E0 Number System *On UPEEXN1 6-42 Off UPEEXN0 6-42 UPC-E0 Check Digit *Off UPECKX0 6-42 On UPECKX1 6-42 UPC-E0 Leading Zero *Off UPENSX0 6-43.
9 - 35 EAN-13 Beginning with 2 Addenda Required * Don’t Require 2 Digit Addenda ARQSY20 6-47 Require 2 Digit Addenda ARQSY21 6-47 EAN-13 Beginning with 290 Addenda Required * Don’t Require 5 Digit.
9 - 36 EAN-13 Beginning with 977 Addenda Required * Don’t Require 2 Digit Addenda ARQ9770 6-50 Require 2 Digit Addenda ARQ9771 6-50 EAN-13 Beginning with 978 Addenda Required * Don’t Require 5 Dig.
9 - 37 EAN/JAN-8 Def ault All EAN/ JAN 8 Settings EA8DFT 6-55 Off EA8ENA0 6-55 *On EA8ENA1 6-55 EAN/JAN-8 Chec k Digit Off EA8CKX0 6-55 *On EA8CKX1 6-55 EAN/JAN-8 Addenda *2 Digit Addenda Off EA8AD20 .
9 - 38 MSI Check Character *V alidate T ype 10, but Don’t T ransmit MSICHK0 6-59 V alidate T ype 10 and Tr a n s m i t MSICHK1 6-59 V alidate 2 T ype 10 Chars, b ut Don’t Tr a n s m i t MSICHK2 6-.
9 - 39 GS1 DataBar Omnidirectional Def ault All GS1 DataBar Omnidirectional Settings RSSDFT 6-62 Off RSSENA0 6-62 *On RSSENA1 6-62 GS1 DataBar Omnidirectional Redundancy Range (0 - 10) *0 RSSVO T## 6-.
9 - 40 GS1 Emulation GS1-128 Emulation EANEMU1 6-66 GS1 DataBar Emulation EANEMU2 6-66 GS1 Code Expansion Off EANEMU3 6-66 EAN8 to EAN13 Conv ersion EANEMU4 6-66 *GS1 Emulation Off EANEMU0 6-66 Po s t.
10 - 1 10 Pr oduct Specifications V oy ager 1250g Scanner Pr oduct Specifications P arameter Specification Mechanical Height 6.63 in. (168mm) Length 3.
10 - 2 Standar d Cable Pinouts Ke yboard W edge 10 Pin RJ41 Modular Plug connects to the base 1 Cable shield 2C a b l e s e l e c t 3 Supply ground 4 Terminal data 5 Terminal clock 6 Keyboard clock 7 Supply power input +5V power 8 Keyboard data 9 10 Note: Pin assignments are not compatib le with Honeywell legacy products.
10 - 3 Standar d Cable Pinouts Serial Output 10 Pin RJ41 Modular Plug connects to the base 1 Cable shield 2C a b l e s e l e c t 3 Supply ground 4 Transmit data 5 Receive data - serial data to scanner 6C T S 7+ 5 V p o w e r 8R T S 9 10 Note: Pin assignments are not compatible with Honeywell legacy products.
10 - 4 Standar d Cable Pinouts RS485 Output 10 Pin RJ41 Modular Plug connects to the base 1 Cable shield 2C a b l e s e l e c t 3 Supply ground 4 Transmit data 5 Receive data - serial data to scanner 6 7+ 5 V p o w e r 8T r a n s m i t E n a b l e 9 10 Note: RS485 signal conversion is performed in the cable.
10 - 5 Standar d Cable Pinouts USB 10 Pin Modular Plug connects to the base 1 Cable shield 2 Cable select 3 Supply ground 4 5 6 7 +5V power 8 9D a t a + 10 Data - Note: Pin assignments are not compatible with Honeywell legacy products. Use of a cable with improper pin assignm ents may lead to damage to the unit.
10 - 6.
11 - 1 11 Maintenance Repairs Repairs and/or upgrades are not to be perf or med on this product. These ser- vices are to be perf or med only by an authorized serv ice center (see Customer Support on page 12-1). Maintenance Y our device provides reliab le and effici ent operation with a minimum of care.
11 - 2 • Order replacement cables from Honeywell or from an authorized distributor. • When ordering a replacement cable, sp ecify the cable part number of the original interface cable. Replacing an Interface Cable 1. Turn the power to the host system OFF.
11 - 3 • You need to program a suffix. Prog ramming a suffix enables the scanner to output the bar code data plus the key you need (such as “CR”) to enter the data into your application. Refer to Prefix/Suffix Overview on page 4- 1 for further information.
11 - 4.
12 - 1 12 Customer Suppor t T echnical Assistance If you need assistance installing or trou bleshooting your device, please call your distributor or the nearest technical support office: North America/Canada Telephone: (800) 782-4263 E-mail: hsmnasupport@honeywell.
12 - 2 Online T echnical Assistance You can also access technical assistance online at www.honeywellaidc.com . Pr oduct Service and Repair Honeywell International Inc. provides service for all its products through service centers throughout the world.
12 - 3 Japan Telephone: +81-3-6730-7344 Fax: +81-3-6730-7222 E-mail: apservic e@honeywell.com Online Product Service and Repair Assistance You can also access product servic e and repair assistance online at www.honeywellaidc.com . Limited W arranty Honeyw ell International Inc.
12 - 4 HA VE BEEN AD VISED OF THE POSSIBILITY OF SUCH INJURIES, LOSSES, OR D AMAGES . SOME ST A TES, PR O VINCES, OR COUNTRIES DO NO T ALLO W THE EXCLUSION OR LIMIT A TIONS OF INCIDENT AL OR CONSE- QUENTIAL D AMAGES , SO THE ABO VE LIMIT A TION OR EXCLUSION MA Y NO T APPL Y T O Y OU.
A - 1 A Reference Charts Symbology Char t Note: Not all symbologies may be supported by your device. Symbology AIM ID P ossible AIM ID Modifiers ( m ) Code ID (hex) All Symbologies (0x99) A ustralian .
A - 2 EAN-8 ]E4 D (0x44) EAN-8 with Add-On ]E3 D (0x44) GS1 Composite ]e m 0-3 y (0x79) GS1 DataBar ]e m 0y ( 0 x 7 9 ) Inf o Mail ]X0 , (0x2c) Intelligent Mail Barcode ]X0 M (0x4D) Interleav ed 2 of .
A - 3 Note: “m” represents the AIM modifier character. Refer to International Technical Specification, Symbology Id entifiers, for AIM modifier character details. Prefix / Suffix entries for specific sym bologies override the universal (All Symbologies, 99) entry.
A - 4 ASCII Con version Chart (Code P age 1252 ) Note: This table applies to U.S. style ke yboards. Certain characters may differ depending on your Country Code/PC regional settings.
A - 5 40 28 ( 72 48 H 104 68 h 41 29 ) 73 49 I 105 69 i 42 2A * 74 4A J 106 6A j 43 2B + 75 4B K 107 6B k 44 2C , 76 4C L 108 6C l 45 2D - 77 4D M 109 6D m 46 2E .
A - 6 Code P age Mapping of Printed Barcodes Code pages define the mapping of charac ter codes to characters . If the data received does not displa y with the pr oper characters, it ma y be because th.
A - 7 the one the host program is e xpecting. If this is the case, select the code page with which the barcodes were created. The data characters should then appear properly . Note: The Code Page option is available for Code 39, Code 93, and Code 128.
A - 8.
.
Sample Symbols UPC-A 0 123456 7890 Interleaved 2 of 5 Code 128 EAN-13 Code 39 Codabar 1234567890 Code 128 9 780330 290951 BC321 A13579B Code 93 123456-9$ Straight 2 of 5 Industrial 123456.
Sample Symbols 6543210 GS1 DataBar (01)00123456789012 Matrix 2 of 5.
Pr ogramming Char t 1 0 2 3 6 7 5 4 8 9.
Pr ogramming Char t Note: If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or digits, and Save again.
Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 VG1250-UG Rev A 06/11.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Honeywell 1250G è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Honeywell 1250G - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Honeywell 1250G imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Honeywell 1250G ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Honeywell 1250G, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Honeywell 1250G.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Honeywell 1250G. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Honeywell 1250G insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
