Manuale d’uso / di manutenzione del prodotto 05177NOS del fabbricante Holley
Vai alla pagina of 18
LS-1 Kit Num ber 051 77NOS OWNER ’S MANU AL P/N A5177- SNOS.
2 CONGRATULATIONS on p urchasing y our NOS Nitrous O xide Inject ion System! Your system is comp osed of the highest quality componen ts available. It should pro vide many miles of trouble-free perfo rmance when used correctly. If you have any questions regar ding the performance o f your system, call NOS Technical Service at 1-866-GOHOLLEY.
3 Never drop or violent ly strike the bottle. Doing so m ay resu lt in an explosive bottle failure. Never change pressure settings of safet y relief valve on the nitrou s bottle valve. Increasing the safe ty relie f valve pressure setti ngs may create an explosive bottle hazard.
4 TABLE OF CONTENTS WHAT IS NITROU S OXIDE? .......................................................................................................5 Do’s and Don’ts of Nitrou s Oxide.................................................................
5 WHAT IS NITROUS O XIDE? NITRO US OXIDE… …Is a cryogenic gas composed of nitrogen and oxygen molecules …Is 36% oxygen by weight …Is non-flammab le by itself …Is stored as a compressed liquid …Exists in two gra des—U.S.P. and Nitrous Plus : U.
6 1.2 Sys tem Requirements W hen used correctly, Kit Number 05177NOS will work with stock LS-1 internal engin e components. To ensure proper performance and driveline longevity, the following i s sugg.
7 Figure 1 Kit Num ber 05177NOS Components Chapter 2 Kit Installation 2.1 Bottle Mounting Instructions NOTE: Disconn ect the battery ground before beginn ing installation. 2.1.1 Street V ehicles Accurate calibra tion of your NOS nitrous sys tem depends on the bottle remaini ng at a stable temperature.
8 Before mounting a nitrous bottle in a racin g vehicle intended for use in sanction ed events, check with the sanctioning association fo r any rules regarding this subj ect.
9 Figure 4 Kit Num ber 05177NOS Assembl y Draw ing.
10 Figure 4A Kit Num ber 05177NOS Installed 4. Use the assemb led bottle/bracket/blow-down tube u nit as a pattern to mark for hole drilling. Drill four 5/16” holes for the bottle bracket b olts, a 1/2” hole for the blow-down tube , and an 11/16” hole for the nitrous supply tube.
11 6. Remove all debris from the airbox before reinstallation. Figure 5 Location of Spray Nozzle Holes in Airbox Figure 6 Spray Nozzle Assembl y 2.5 Solenoi d Mounting Use the following procedure to install the nitrous solenoids. CAUTION: Do not o vertighten the vise in the following procedure, or the solenoi d will be damaged.
12 2.6 Nitrous Fe ed Line Mounting HINT: Following the fuel lines along the left side of t he vehicle and entering the engine b ay near the master cylinder works well. 1. Determine the route for your nitrous feed line to follo w. Ensure the path is clear of exhaust system, suspension , steering, wheels, elec trical lines and components, and ti res.
13 WARNING: Be c areful when removing the fue l rail test port fitting. The fue l rail may be pressurized. Alwa y s allow the engine to co ol before performing this operation. Fuel sprayed onto hot engine component s may start a fire. 2. Remove the cap over the fuel rail test port on the front of the driver’s side fuel rail .
14 Figure 10 Microsw itch Mounting Locatio n—shown at idle. Figure 11 Microsw itch Mounting Locatio n—shown at W.O.T..
15 2.9 Preparing for Operation 1. Start the vehicle . 2. Open the nit rous bottle valve. There should be no chan ge in the engine idle speed or exhaust tone. If either change is noted, refe r to Appendix A, Troubleshooting Guide . 3. Inspect the nitrous lines and fittings for leaks.
16 Too much ni trous flow. Reduce nit rous jetting. Inadequate fu el delivery due to: Plugged fuel filter Inspect fuel filter. Clean or replace f ilter. Crimped fuel line . Inspect fuel line. Replace c rimped line. Engine detona tes heavily when s ystem is activated.
17 Nitrous Press ure Gauges (P/N 15910NOS) measu re from 0-1500 psi (although recomm ended level is 900-950 psi) and are essential in mon itoring the bottle. The Quick Rele ase Hinged Aluminum Bracke t (P/N 14140NOS) is available fo r 10 lb. and 15 lb.
18 NOS Techni cal Support Phone: 1-270- 781-9741 Toll-Phone: 1-866-GO HOLLEY Fax: 1- 270-781-9772 For online hel p, please check the Tech Service se ction of our website : www .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Holley 05177NOS è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Holley 05177NOS - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Holley 05177NOS imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Holley 05177NOS ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Holley 05177NOS, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Holley 05177NOS.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Holley 05177NOS. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Holley 05177NOS insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
