Manuale d’uso / di manutenzione del prodotto CF-941 del fabbricante Henny Penny
Vai alla pagina of 19
OPERATOR’S MANUAL Henny Penny Multipurpose Holding Cabinet Model CF-941 REGISTER WARRANTY ONLINE AT WWW.HENNYPENNY.COM.
.
Model CF-941 LIMITED WARRANTY FOR HENNY PENNY EQUIPMENT Subject to the following conditi ons, Henny Penny Corporation m akes the following l imit ed warranties to the original purchaser only for Henny.
.
Model CF-941 TABLE OF CONTENTS Section Page Section 1. INTRODUCTION ............................................................................................... 1-1 1-1. Multipurpose Holding Cabinet .................................................
.
Model CF-941 SECTION 1. INTRODUCTION 1-1. MULTIPURPOSE The Henny Penny Multipurpose Holding Cabinet HOLDING CABINET is a basic unit of food equipment designed to hold hot foods at proper temperature in comm ercial food operations. This cabinet will keep hot foods humid while maintaining temperature.
Model CF-941 1-5. SAFETY The only way to ensure safe operation of the Henny Penny Multipurpose Holding Cabinet is to fully understand the proper installation, operation and maintenance procedures. The instructions in this manual have been prepared to aid you in learning the proper procedures.
Model CF-941 SECTION 2. INSTALLATION 2-1. INTRODUCTION This section provides the installation instructions for the Henny Penny Multipurpose Holding Cabinet. Installation of this unit should be performed by a qualified service technician. Do not puncture the skin of unit with drills or screws as component damage or electrical shock could result.
Model CF-941 2-2. UNPACKING (Continued) 5. Pull off any protective covering from the exterior of the cabinet. 6. Your multipurpose holding cabinet is now ready for location and setup. 2-3. ELECTRICAL The multipurpose holding cabinet is available from REQUIREMENTS the factory as a 120 VAC unit.
Model CF-941 SECTION 3. OPERATION 3-1. INTRODUCTION This section provides operating procedures for the multipurpose holding cabinets. Read the Introduction, Installation and Operation Sections and all instructions should be followed before operating the cabinet.
Model CF-941 Figure 3-1 3-3. START-UP Before using the cabinet, it should be thoroughly cleaned as described in the cleaning procedures section of this manual. To put the cabinet into operation, move each POWER switch to the ON position and adjust each control to the appropriate temperature.
Model CF-941 3-5. CLEANING 1. Move the POWER switch to the OFF position. 2. Disconnect the electrical supply to the unit. To avoid burns, allow the unit to cool before cleaning by opening all the drawers fully for approximately 20 minutes. 3. Remove drawers by pulling straight out and tilting up.
Model CF-941 3-6. OPERATION AND Unit Operation PROGRAMMING Before operating the holding cabinet, read and understand this complete operation manual (supplied with each unit). The following steps are meant to be guidelines, not complete operating instructions.
Model CF-941 3-6. OPERATION AND Timer Settings PROGRAMMING (Continued) To change a timer setpoint, press and hold the desired timer button, then use the UP and DOWN buttons to change the time. Releasing the timer button enters the time into the controls.
Model CF-941 3-6. OPERATION AND 6. Press and release the SET button 4 times and “In-” PROGRAMMING shows in the display. In- means initialization. Press (Continued) and hold the UP or DOWN button at this time and allow the display to count down from 3.
Model CF-941 G L O S S A R Y HENNY PENNY HOLDING CABINETS air temperature probe a round device located inside the cabinet that m easures the inside air temperature and sends t hat information t o the .
Model CF-941 probe clip a metal holder that attaches to the outsi de of the control panel to hold t he food probe when not in use; the clip is an optional accessory product load capacity the highest r.
*FM05-016-B* Henny Penny Corp., Eaton, Ohio 45320, Revised 02-14-07 Henny Penny Corporation P.O.Box 60 Eaton,OH 45320 1-937-456-8400 1-937-456-8402 Fax Toll free in USA 1-800-417-8417 1-800-417-8434 Fax www.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Henny Penny CF-941 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Henny Penny CF-941 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Henny Penny CF-941 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Henny Penny CF-941 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Henny Penny CF-941, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Henny Penny CF-941.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Henny Penny CF-941. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Henny Penny CF-941 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
