Manuale d’uso / di manutenzione del prodotto RT380H del fabbricante Hayter
Vai alla pagina of 52
Operator ’ sManual RT380H T ractor with Recycling/Side Discharge Deck G006889 Code 135E Serial No. 280000001 Manual Part No. 1 1 1-2091 Rev C.
Introduction R ead this infor mation carefully to learn ho w to operate and maintain your product properly and to av oid injur y and product damage. Y ou are responsible for operating the product properly and safely .
Fuel System Maintenance .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 28 Draining the Fuel T ank . .. .. .. .. .. .. .. .. .. . .. .. .. .. .. .. .. .. .. . 28 R eplacing the Fuel Filter . . . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .
• Thoroughly inspect the area where the equipment is to be used and remov e all objects whic h may be thrown by the mac hine. • W ar ning —Fuel is highly ammable . – Store fuel in containers specically designed for this purpose. – R efuel outdoors only and do not smok e while refuelling .
• R educe the throttle setting during engine r un-out and, if the engine is pro vided with a shut-off v alv e, turn the fuel off at the conclusion of mowing . • Use only Ha yter -approv ed attac hments . T he warranty ma y be v oided if y ou use the tractor with unapprov ed attachments .
Slope Chart 6.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger . R eplace any decal that is damag ed or lost. 92-5730 1. Choke 3. Continuous variable setting 2. Fast 4.
93-6677 1. W arning—don’t operate the mower with the deector up or removed; keep the deector in place. 2. Cutting/dismemberment hazard of hand or foot, mower blade—stay away from moving parts. 93-6679 1. Engine 93-7009 1. W arning—don’t operate the mower with the deector up or removed; keep the deector in place.
100-7449 1. Pull the lever out to push the machine. 3. Read the instructions before servicing or performing maintenance. 2. Push the lever in to ride on the machine.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty . Use Front wheels 2 Shim washers (as required) 2 Flat washers 2 Cotter pins 2 1 Hub caps 2 Install the front wheels. 2 No parts required – Check the tyre pressure.
1 Installing the Front Wheels Parts needed for this procedure: 2 Front wheels 2 Shim washers (as required) 2 Flat washers 2 Cotter pins 2 Hub caps Procedure 1. Install the shim washers onto the axle . 2. Install the wheel onto the axle with the v alve stem facing out.
Figure 5 1. Steering wheel 2. Spirol pin 3. Align the holes b y inserting a punc h or a long nail partially through the holes in the steering wheel and shaft. 4. Insert the spirol pin into the hole on the opposite side (Figure 5). 5. Using a hammer, driv e the spirol pin in until it is ush with the outside of the steering wheel (Figure 5).
Batter y electrol yte contains sulfuric acid, a deadly poison that can sev erely bur n y ou and others. • Do not drink electrolyte and av oid contact with skin, eyes, or clothing . W ear safety glasses to shield y our eyes and rubber glo v es to protect y our hands.
7 Installing the Anti-Scalp Wheels Parts needed for this procedure: 2 Anti-scalp wheels 2 Wheel bolt 2 Locknut Procedure Mount the anti-scalp wheels onto the wheel brack ets with the wheel bolts and lockn ut (Figure 9). Figure 9 1. Wheel 3. Locknut 2.
Figure 10 1. Operate position 2. Push position 3. R un the engine at a low idle and mo ve the traction control pedal forward for 5 seconds , then rev erse for 5 seconds . R epeat this step 3 times . 4. Place the driv e control in the Operate position (Figure 10) and driv e the tractor forward about 5 feet (1.
13 Checking the T raction Control Pedal No Parts Required Procedure If the tractor driv es too fast or slo w with the traction control pedal fully pressed in either direction, you can adjust it to set the optim um forward and reverse speeds , as follows: 1.
Operation Note: Determine the left and right sides of the machine from the nor mal operating position. Petrol and Oil Use unleaded petrol suitable for automotiv e use (85 pump octane minim um). In cer tain conditions, petrol is extremely ammable and highly explosi v e.
• It cleans the engine while it r uns . • It eliminates gum-like v arnish buildup in the fuel system, which causes hard starting . Important: Do not use fuel additi ves containing methanol or ethanol. Add the cor rect amount of fuel stabilizer/conditioner to the petrol.
Operating the Blade Control (PT O) The blade control (PTO) engages and disengag es pow er to the electric clutc h. Engaging the Power T ake Off (PT O) 1. Press the clutc h/brake pedal to stop the tractor . 2. Pull the blade control (PTO) to on (Figure 16).
Stopping the Engine 1. Shift the throttle lev er to F ast (Figure 18). 2. T urn the ignition k ey to Off , w ait for all mo ving parts to stop , and remo v e the k ey before leaving the operating position.
Figure 21 1. Operating-in-reverse light 4. Shift the traction control switc h into R ev erse and complete y our task. 5. Disengag e the blade control (PTO) to activ ate the interlock. 6. R emov e the rev erse interloc k key and put it in a safe place out of the reac h of children.
Driving Forward or Backward The throttle control regulates the engine speed as measured in RPM (rev olutions per minute). Shift the throttle control lev er into the F ast position for best perfor mance. T o g o forw ard or bac kward: 1. R elease the parking brake; refer to R eleasing the P arking Brak e .
2. Lift the grass deector and slide the tabs on top of the discharge co v er under the grass deector retaining rod. 3. R otate the discharge co v er do wn over the opening, and onto the lo wer lip of the cutter dec k (Figure 24). G008145 1 2 3 4 5 5 6 6 Figure 24 1.
Maintenance Note: Deter mine the left and right sides of the machine from the nor mal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the rst 5 hours • Change the engine oil. Before each use or daily • Check the engine oil level.
Lubrication Greasing and Lubricating the T ractor Ser vice Inter v al: Ev ery 25 hours—Grease and lubricate the tractor . More often in dusty or dirty conditions . How to Grease the T ractor 1. Disengag e the blade control (PTO). 2. Set the parking brake .
7. Unscrew the oil dipstic k and wipe the metal end clean (Figure 28). Figure 28 1. Oil dipstick 2. Metal end 8. Screw the oil dipstic k fully onto the ll hole.
2. Set the parking brake . 3. Stop the engine , wait for all moving parts to stop , and remov e the k ey before leaving the operating position. 4. Open the hood. 5. Clean around the air cleaner to prev ent dirt from getting into the engine and causing damage .
Figure 32 1. Spark-plug wire 6. Clean around the spark plug to prevent dirt from falling into the engine and potentially causing damage. 7. R emov e the spark plug and metal washer . Checking the Spark Plug 1. Look at the center of the spark plug (Figure 33).
Figure 34 1. Hose clamp 3. Fuel lter 2. Fuel line 6. Squeeze the ends of the hose clamp together and slide it up the fuel line to ward the fuel tank (Figure 34). 7. Pull the fuel line off of the fuel lter (Figure 34) and allow petrol to drain into a fuel container or a drain pan.
Figure 35 1. Negative cable (black) 4. Battery box 2. Rubber cover 5. Bolt and wing nut 3. Positive cable (red) Incor rectly routing the batter y cable could damage the tractor and ca bles, causing sparks. Sparks can cause the batter y gasses to explode, resulting in personal injur y .
Important: Do not ov erll the batter y because electrolyte (sulfuric acid) can cause severe cor rosion and damage to the chassis. 5. W ait 5 to 10 min utes after lling the battery cells . Add distilled water , if necessary , until the electrolyte level is up to the Upper line (Figure 36) on the batter y case .
Figure 39 1. Bulb holder 4. Slots 2. Reector 5. T erminals 3. T abs 4. Insert and rotate the bulb countercloc kwise until it stops (appro x. 1/4 turn), and remove the bulb from the bulb holder (Figure 40). Figure 40 1. Bulb 3. Bulb holder 2. Metal pins 4.
Figure 42 1. Fill plug 5. R emov e the ll plug and chec k the uid level. Note: The lev el should be a maxim um of 1-1/4 inch (32 mm) belo w the top of the ll por t (Figure 42).
Brake Maintenance Servicing the Parking Brake Ser vice Inter v al: Before each use or daily The parking brake is on the right side of the rear axle, inside the rear tyre (Figure 43). If the parking brake does not hold securely , adjust it. Figure 43 1.
Belt Maintenance Replacing the Blade Drive Belt Removing the Blade Drive Belt 1. R emov e the cutter dec k; refer to R emo ving the Cutter Deck. 2. R emov e the pulley cov er mounting screws and pulley cov ers from both blade pulleys (Figure 44). Figure 44 1.
3. R emov e the bolt (5/8 inch wrench), cur v ed washer , retainer , and blade (Figure 46). Use a bloc k of w ood as a wedge between the blade and the cutter deck to lock the blade when you are remo ving the bolt. Figure 46 1. Bolt 4. Spindle 2. Retainer 5.
Figure 50 1. Idler spring 3. Idler arm 2. Eye-bolt 4. Idler pulley 8. R emov e the bolts and lock nuts and pull the tw o cutter dec k piv ot mount brac kets do wn from the front axle (Figure 51). Figure 51 1. Pivot mount bracket 3. Locknut 2. Bolt (5/16 x 2-1/2 inch) 9.
Installing the Cutter Deck Without the grass deector , discharge co v er , or complete grass catcher assembly mounted in place, y ou and others are exposed to blade contact and thrown de bris. Contact with the rotating cutter deck blade(s) and thrown de bris will cause injur y or death.
Figure 57 1. Idler spring 3. Idler arm 2. Eye-bolt 4. Idler pulley 17. Mo v e the height-of-cut lev er into the D notch to make it easier to install the height-of-cut lift assist spring . 18. Hook the lift assist spring between the cutter deck right side lift brac ket and the retaining bolt (Figure 58).
9. R epeat 7 and 8 on the opposite side of the cutter deck. 10. Chec k the front-to-rear blade slope; refer to Adjusting the Front-to-R ear Blade Slope. Adjusting the Front-to-Rear Blade Slope Check the front-to-rear blade slope whenev er you install the cutter deck.
13. When the front-to-rear slope is cor rect, tighten the piv ot plate mounting bolts (Figure 63). 14. When the front-to-rear blade slope is correct, c heck the side-to-side lev el of the cutter dec k; refer to Leveling the Cutter Deck from Side-to-Side .
A broken or missing w ashout tting could expose y ou and others to thrown objects or to blade contact. Contact with the blade or thrown debris contact may cause injur y or death. • Replace broken or missing w ashout tting immediately , before using the cutter deck again.
10. R emo v e and inspect the spark plug; refer to Ser vicing the Spark Plug . With the spark plug remo ved from the engine, pour 2 tablespoons of engine oil into the spark plug hole . Use the electric starter to crank the engine and distribute the oil inside the cylinder .
T roubleshooting Problem Possible Cause Corrective Action 1. The blade control (PTO) is engaged. 1. Disengage the blade control (PT O). 2. The parking brake is not on. 2. Set the parking brake. 3. The battery is dead. 3. Charge the battery . 4. The electrical connections are corroded or loose.
Problem Possible Cause Corrective Action 1. The drive control is in the Push position. 1. Move the drive control to the Operate position. 2. The traction belt is worn, loose, or broken. 2. Contact an Authorized Service Dealer . The tractor does not drive.
Schematics Wiring Diagram (Rev . A) 46.
Notes: 47.
Notes: 48.
1st Y ear (12 months) W e certify that this service has been carried out by an Authorised Hayter Service Dealer Date: 1st Y ear (12 months) Owner’s Name: Serial Number: Date: 2nd Y ear (24 months) W.
.
LIMITED WARRANTY Hayter Limited warrants to the original user/purchaser that this unit shall be free from defect s in material and workmanship under normal use and service for a period of three years from the date of purchase. The manufacturer of major proprietry components ie.
CUS T OME R INFO RMA TI ON Date of Sale:- Y our Local Dealer:- HA Y TER L IM ITED , SPEL L BR OO K, BI SHOP ’S S T OR TF ORD , H E R T S . C M 23 4B U, E N G L A N D Code Serial No.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Hayter RT380H è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Hayter RT380H - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Hayter RT380H imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Hayter RT380H ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Hayter RT380H, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Hayter RT380H.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Hayter RT380H. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Hayter RT380H insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
