Manuale d’uso / di manutenzione del prodotto AD1202 del fabbricante American Dynamics
Vai alla pagina of 32
Model AD1202 MCS Coax Controller Installation and Operating Instructions This manual describes the installation and operating procedures for the AD1202 MCS Coax Pan/Tilt and Lens Controller. The AD1202 Controller allows coax control of four color or monochrome cameras via the video line to the camera site.
The software/firmware furnished with this equipment is confidential to and is copyrighted by SENSORMATIC ELECTRONICS CORPORATION. It is not to be copied or disclosed in any manner without the express written consent of SENSORMATIC. The software/firmware is furnished to the purchaser under a license for use on a single system.
The installation of this product should be made by qualified service personnel and should conform to all local codes. QA301D ! W W W W A A A A R R R R N N N N II I I N N N N G G G G To reduce the risk of fire or shock hazard, do not expose this product to rain or moisture.
.
CONTENTS Page DESCRIPTION................................................................................................. 1 FEA TURES ....................................................................................................... 1 INST ALLA TION .
.
DESCRIPTION The AD1202 MCS Coax Controller is a compact Pan/Tilt, Lens, Preset Scene, and Auxiliary controller for four color or monochrome cameras. The AD1202 provides coax control of four cameras via the video line connection to the camera site.
CONNECTIONS All connections to the AD1202 Coax Controller are made on the unit’s rear panel, illustrated in Figure 2. Typical AD1202 connections with other AD units are illustrated in the Typical System Connections section at the end of this manual.
EXTERNAL Connector A 24-pin connector on the rear panel, labeled EXTERNAL, provides pins for external alarm inputs and control signals. A mating 24-pin plug-in connector with flying leads is provided.
EXTERNAL Connector (Continued) AD MANCHESTER CONTROL CODE OUTPUTS The EXTERNAL connector provides two sets of AD Manchester Control Code lines (Code 1 - pins 5 - 7, and Code 2 - pins 8 - 10) for output of camera control commands (camera pan/tilt/lens/preset/aux) to AD Manchester Control Code units, such as camera site Receivers.
FRONT PANEL CONTROLS The following front panel controls are provided for operator control of a camera site (see Figure 5). The use of these controls is described in the SETUP and OPERATION sections of this manual, pages 6 through 9.
SETUP Factory Reset The AD1202 can be reset to factory default settings which are as follows: • resets the programmed AD1202 camera inputs (see Camera Programming) to cameras 1 through 4, respective.
To program a specific camera select button for a switcher camera number: 1. Press the front panel PGM button on the AD1202. The PGM LED illuminates steadily, and the Channel Select button 1 LED flashes repeatedly. 2. Press the desired AD1202 Channel Select button for the specific camera input to be programmed.
If an input is set as unterminated, that input must be looped to a terminated video device using the lower BNC connector (see Looping Video Outputs, page 2). Coax Code Selection The AD1202 provides two different types of code output for coax control to a camera Receiver: Standard or Enhanced UTC code.
9 Calling a Preset Camera Scene A suitably equipped AD Receiver can store a maximum of 72 preset scenes. The AD1202 can call any of the first four preset scenes using the front panel PRESET buttons. See Preset Scene Programming, page 7, to program preset scenes.
.
Appendix.
BUILT-IN TEST The AD1202 has a built-in test procedure that provides a verification of AD1202 front panel controls. To operate the built-in test: 1. Remove power from the AD1202, and remove the cover from the unit. 2. Press the TEST button on the PCB while applying power to the unit.
T ypical System Connections.
TYPICAL SYSTEM CONNECTIONS AD1202 with four AD1641U Coax Receivers and Alarms REMOTE ALARM CONTACT 3 REMOTE ALARM CONTACT 4 C-2 AD1202 LOOPING VIDEO OUPUTS, ALL INPUTS UNTERMINATED REMOTE ALARM CONTAC.
TYPICAL SYSTEM CONNECTION AD1202 with two AD1641U Coax and two AD1641M Control Code Receivers CAMERA 4 CAMERA 3 AD1202 1 3 5 7 9 11 13 15 17 19 21 23 2 4 6 8 10 12 14 16 18 20 22 24 * 120-Ohm Terminat.
TYPICAL SYSTEM CONNECTION AD1202 with two AD1240 Series P/Ts and two AD1641U Coax Receivers CAMERA 4 AD1202 1 3 5 7 9 11 13 15 17 19 21 23 2 4 6 8 10 12 14 16 18 20 22 24 W B C-4 ALL INPUTS TERMINATED IN 75 Ω LOCAL MONITOR AD1641U COAX RECEIVER AD1641U COAX RECEIVER NOTE: AD1641 Series Receivers shown for illustration.
C-5 TYPICAL SYSTEM CONNECTIONS Two AD1202 Controllers with AD1408A Switcher AD1408A AUX Connector: Pin 1 - Camera ID, bit 0 Pin 2 - Camera ID, bit 1 Pin 3 - Camera ID, bit 2 Pin 4 - Ground AD1408A AD1.
.
Index.
.
AD Manchester Control Code Outputs . . . . . . . . . . . . . . . . 4 Alarm Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Alarm Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Alarm Response .
.
Problem Possible Causes Suggested Action Operating Problems Cannot program camera numbers or Programming Blocking feature enabled Check and enable front panel controls (page 5) preset scenes No AD1202.
.
Declaration of Conformity Manufacturer: Sensormatic CCTV Systems Division Manufacturer’s Address: Sensormatic CCTV Systems Division Sensormatic CCTV Systems Division 1 Blue Hill Plaza 600 Bradley Hi.
SPECIFICATIONS Electrical Ratings: AD1202: 120 VAC, 50/60 Hz, 9 W ADS1202X: 230 VAC, 50/60 Hz, 50 mA Video Signal: AD1202 - EIA RS-170/NTSC Video, 525 lines @ 60 Hz ADS1202X - CCIR/PAL Video, 625 line.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il American Dynamics AD1202 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del American Dynamics AD1202 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso American Dynamics AD1202 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul American Dynamics AD1202 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il American Dynamics AD1202, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del American Dynamics AD1202.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il American Dynamics AD1202. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo American Dynamics AD1202 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
