Manuale d’uso / di manutenzione del prodotto G1199 del fabbricante Grizzly
Vai alla pagina of 29
DRILL PRESS MODEL G1199/G1200 INSTRUCTION MANUAL COPYRIGHT © 1990 BY GRIZZLY IMPORTS, INC. REG. #3176563 WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY IMPORTS, INC.
-B- G1199/G1200 Drill Press WARNING Some dust created by power sanding, sawing, grind- ing, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints.
Table Of Contents PAGE 1. INTRODUCTION ........................................................................................................2 SAFETY RULES FOR ALL TOOLS ........................................................................3 UNPACKING.
-2- G1199/G1200 Drill Press Grizzly Imports, Inc. is proud to offer the Model G1199/G1200 Drill Press. This drill press is a part of Grizzly’s growing family of fine woodworking and metalworking machinery. When used accord- ing to the guidelines stated in this manual, you can expect years of trouble-free, enjoyable oper- ation.
G1199/G1200 Drill Press -3- 12. USE SAFETY GLASSES AND EAR PRO- TECTION. Also use a DUST MASK if the operation is dusty. 13. DO NOT OVERREACH. Keep proper footing and balance at all times. 14. MAINTAIN TOOLS IN TOP CONDITION. Keep tools sharp and clean for best and safest performance.
G1199/G1200 Drill Press -4- Unpacking The Model G1199/G1200 Drill press is shipped from the manufacturer in a carefully packed car- ton. If you discover the machine is damaged after you’ve signed for delivery, please call Customer Service immediately for advice.
G1199/G1200 Drill Press -5- Clean up The column and other unpainted parts of the Model G1199/G1200 are coated with a waxy oil that protects them from corrosion during ship- ment. Remove the protective coating with miner- al spirits and paper towels. Do not use gasoline or other petroleum based solvents because of their extremely low flash points.
-6- G1199/G1200 Drill Press Circuit Requirements The motor supplied with the G1199/G1200 is a 110V single-voltage motor, prewired for 110V. Under normal use, the motor draws approximate- ly 9 amps @ 110V. We recommend using a 15 amp circuit breaker or a 15 amp slow blow fuse for 110V operation.
G1199/G1200 Drill Press -7- Beginning Assembly Most of the Drill Press has been pre-assembled at the factory. The few remaining pieces should go together quickly and easily. Assembly is straight forward and with just a few tools you can do the entire job quickly and easily.
-8- G1199/G1200 Drill Press Figure 4. Figure 3. Worm pinion installed. Figure 5. 3. Insert the worm pinion inside the table brack- et and attach the crank handle by tightening the setscrew. Figure 3. 4. The rack has a section on each end with no teeth.
G1199/G1200 Drill Press -9- Figure 6. Installing the table. 2. Turn the crank handle to be sure the worm pinion engages the teeth on the rack and moves the bracket up and down. Figure 7. CAUTION: Never use the drill press with either table lock loose.
-10- G1199/G1200 Drill Press Drill Chuck Figure 9. Drill chuck assembly. The Drill Press chuck and arbor must be mount- ed in the drill press spindle. The arbor has a #6 Jacobs Taper on one end and a #2 Morse Taper on the other. The #6 Jacobs Taper fits into the drill chuck and the #2 Morse Taper fits in the drill press spindle.
G1199/G1200 Drill Press -11- Speed Change SECTION 3: ADJUSTMENTS Remember to disconnect the drill press from the power source before attempting any adjustments. 1. To change speed, loosen the two lock knobs, one on either side of the head. Figure 10. 2.
-12- G1199/G1200 Drill Press To stop the vertical travel of the drill bit at a desired depth, loosen the scale set knob located on the feed shaft assembly, rotate the handles to the desired depth and tighten the scale set knob. Figure 12. To hold a stationary depth, loosen the scale set knob and rotate the feed shaft to its lowest point.
G1199/G1200 Drill Press -13- Figure 15. Figure 14. 4. To tilt the table, loosen the pivot bolt and remove the locator pin ( Figure 15 ). This is done by tightening the nut until the pin is extracted from its hole. Tilt the table to the desired angle (up to 45°) and re-tighten the pivot bolt.
-14- G1199/G1200 Drill Press Caution Always wear ANSI-approved safety glasses or goggles when operating equipment — particularly when test- ing new tools or machinery.
G1199/G1200 Drill Press -15- Once the assembly is complete and the adjust- ments are done to your satisfaction, you are ready to test the machine. Turn on the power supply at the main panel. Press the START button. Make sure that your fin- ger is poised on the STOP button, just in case there’s a problem.
-16- G1199/G1200 Drill Press Drilling Metal When drilling metal, use clamps to hold the work- piece securely in place. The workpiece should never be held in place by bare hands. The cutting edge can catch in the material at any time, result- ing in serious injury.
G1199/G1200 Drill Press -17- Figure 18. Mortise Attachment installed. Mortise Attachment The optional Grizzly G1083 Mortise Attachment was specifically designed to fit the G1199/G1200 Drill Presses. Refer to our current catalog for ordering information.
-18- G1199/G1200 Drill Press SECTION 5: MAINTENANCE Lubrication Belt Tension Shielded and pre-lubricated ball bearings require no lubrication for the life of the bearings. In a con- tinuous-use environment, expect the bearings to last for several years.
G1199/G1200 Drill Press -19- The following pages contain parts diagram, parts list, general machine data, trouble shooting guide and Warranty/Return information for your Model G1199/G1200 Drill Press.
1 2 3 5 4 22 12 20 15 14 13 16 21 17 18 6 19 7 8 9 11 10 46 48 37 43 45 44 42 41 38 29 100 30 31 24 23 82 26 33 26 78 77 74 76 75 35 34 36 79 81 80 99 90 92 91 93 99 69 70 65 68 66 67 66 68 86 89 88 8.
G1199/G1200 Drill Press -21- 1 P1199001 BASE 2 P1199002 COLUMN HOLDER 4 P1199004 COLUMN 5 PB31M HEX BOLT M10-1.5 X 40 6 P1199006 BRACKET 7 P1199007 PINION GEAR 8 P1199008 GEAR SHAFT 9 P1199009 WORM PINION 10 P1199010 CRANK HANDLE 11 PSS01M SETSCREW M6-1.
-22- G1199/G1200 Drill Press MACHINE DATA GRIZZLY MODEL G1199 & G1200 DRILL PRESS Design Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Bench Model/Floor Model Overall Dimensions Table Size . . . . . . . .
G1199/G1200 Drill Press -23- TROUBLESHOOTING WARNING: For your own safety, turn the switch off and disconnect power source before troubleshooting. Trouble Probable Cause Remedy Noisy operation 1. Incorrect belt tension 1. Adjust tension 2. Dry spindle 2.
-24- G1199/G1200 Drill Press Grizzly Imports, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, neg- ligence, accidents, repairs or alterations or lack of maintenance.
G1199/G1200 Drill Press -25- Recommended RPM Drill Cast Diameter Iron Steel Aluminum Wood 1 ⁄ 8 " 1900 2620 2620 2620 3 ⁄ 16 " 1550 1620 2620 2620 1 ⁄ 4 " 990 1350 1550 2620 5 ⁄.
D C B A 4 3 2 1 4 3 2 1 RPM :250 BELT: A-1, 4-4 1 D C B A 4 3 2 1 4 3 2 1 RPM : 510 BELT: B-2, 3-3 4 D C B A 4 3 2 1 4 3 2 1 RPM : 990 BELT:D-4, 3-3 7 D C B A 4 3 2 1 4 3 2 1 RPM : 1900 BELT: D-4, 2-2.
G1199/G1200 Drill Press -27- NOTES:.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Grizzly G1199 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Grizzly G1199 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Grizzly G1199 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Grizzly G1199 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Grizzly G1199, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Grizzly G1199.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Grizzly G1199. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Grizzly G1199 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
