Manuale d’uso / di manutenzione del prodotto GP160 del fabbricante Golden Technologies
Vai alla pagina of 42
.
LiteRider PTC_Owner’s Manual Rev A_121911 .
LiteRider PTC_Owner’s Manual Rev A_121911 Thank you for purchasing your LiteRider P TC (Personal Transport Chair). We are honored you have chosen Golden Technologies for your mobility needs.
LiteRider PTC_Owner’s Manual Rev A_121911 CONTENTS I. Introduction……………………………………………………………………………………… 4-5 II. Safety…………………………………………………………………………………………….
LiteRider PTC_Owner’s Manual Rev A_121911 I. INTRODUCTION Congratulations on the purchase of your new Lit eRider PTC (Personal Transport Chair). The Lit eRider PTC , combines cutting edge technology with attractive designs that are also highly functional in today’s world.
LiteRider PTC_Owner’s Manual Rev A_121911 Socket/Wrenches - 17mm, 14mm, 10mm, and 8mm. Allen Wrenches – 8mm , 5mm , and 4mm. I. INTRODUCTION ACCESSORIES for the LiteRider PTC : (Personal Transport Chair) A variety of accessories are available for your Golden Lit eRider PTC .
LiteRider PTC_Owner’s Manual Rev A_121911 II. SAFETY Your Golden Lit eRider PTC is a battery-operated personal mobility vehicle. Please exercise caution and consideration when you are operating it. Driving your LiteRider PTC carefully and thoughtfully will help ensure your personal safety and the safety of other people.
LiteRider PTC_Owner’s Manual Rev A_121911 II. SAFETY DRIVING ON AN INCLINE • Drive with caution when attempting to negotiate any incline, even handicap access ramps. • Always climb or descend a gradient by driving straight up or straight down the face of the slope.
LiteRider PTC_Owner’s Manual Rev A_121911 II. SAFETY SAFETY RULES • Do not attempt to use your Lit eRider PTC on an escalator. Always use an elevator. • Do not carry passengers on your power chair. • Do not operate your Lit eRider PTC, if it is not functioning properly.
LiteRider PTC_Owner’s Manual Rev A_121911 II. SAFETY Please be sure to follow this important warning when transferring onto or off the Golden Lit eRider PTC : (Personal Transport Chair) NEVER TRANSFER ON OR OFF OF THIS POWER WHEELCHAIR USING THE SEAT BACKREST FOR SUPPORT DURING TRANSFER.
LiteRider PTC_Owner’s Manual Rev A_121911 III. EMI/RFI The rapid development of electronics, especially in the area of communications, has saturated our environment with electromagnetic (radio) wave.
LiteRider PTC_Owner’s Manual Rev A_121911 IV. ASSEMBLY Your Lit eRider PTC is shipped partially disassembled in order to maximize the protection of all its parts during the shipping process. Please follow the instructions below to quickly and easily assemble the power chair for your use.
LiteRider PTC_Owner’s Manual Rev A_121911 IV. ASSEMBLY Before operating or assembling your LiteRi der PTC , be sure to remove the battery deactivate strip and connect the joystick cable to the VR2 controller. Your Lit eRider PTC will not power up or operate without completing these steps.
LiteRider PTC_Owner’s Manual Rev A_121911 IV. ASSEMBLY Seat Installation 1. Fold the seat back down . 2. Grasp the seat firmly on each side, lift the seat and align the seat pin with the hole in the seat post receiver. See figure 4. 3. Insert the seat into the seat post.
LiteRider PTC_Owner’s Manual Rev A_121911 IV. ASSEMBLY Arm Installation 1. Loosen the arm width adjustment screw from the arm receiver tube at the bottom rear of the seat frame with a 4mm Allen wrench. See figure 5. 2. Insert the arm into the arm receiver tube, so that the arm pad faces toward the front of the unit.
LiteRider PTC_Owner’s Manual Rev A_121911 IV. ASSEMBLY Joystick Installation 1. Loosen the joystick bracket adjustment screw located under the armrest. See figure 6. 2. Insert the joystick mounting tube into the joystick bracket under the armrest. 3.
LiteRider PTC_Owner’s Manual Rev A_121911 V. DISASSEMBLY and BATTERY REPLACEMENT To disassemble your Lit eRider PTC , simply reverse the assembly process. See pages 11-15. Make certain that the controller power is turned off and that the chair is NOT in freewheel mode before attempting to perform disassembly.
LiteRider PTC_Owner’s Manual Rev A_121911 VI. COMFORT SETTINGS You may be spending a great deal of time on your Lit eRider PTC . T o provide you with the maximum seating comfort, Golden Technologies, Inc. has designed this power chair to incorporate the following adjustments for operator comfort.
LiteRider PTC_Owner’s Manual Rev A_121911 VI. COMFORT SETTINGS Arm Width Adjustment 1. Loosen the adjustment screw at the rear of the seat with a 4mm Allen wrench. See figure 9. 2. Slide the arm in or out to the desired width. 3. Tighten the adjustment screw to secure the arm.
LiteRider PTC_Owner’s Manual Rev A_121911 VI. COMFORT SETTINGS Footrest Angle Adjustment 1. Fold the footrest upward for easy access to the angle adjustment bolt. See figure 11. 2. Turn the jam nut counter-clockwise with a 17mm wrench to loosen. 3. Use an 8mm Allen wrench to turn the adjustment bolt.
LiteRider PTC_Owner’s Manual Rev A_121911 VI. COMFORT SETTINGS Joystick Bracket Length Adjustment 1. Loosen the adjustment knob. See figure 13. 2. Slide the joystick holder in or out to the desired position.
LiteRider PTC_Owner’s Manual Rev A_121911 VII. OPERATION Your Lit eRider PTC is simple to operate. However, for your safety and the safety of others, Golden Technologies, Inc. recommends that you carefully read and understand the following operating instructions.
LiteRider PTC_Owner’s Manual Rev A_121911 VII. OPERATION The Joystick The joystick (see figure 15 on page 24) controls the speed (up to the maximum limit set by the speed control buttons) and direction of your power chair.
LiteRider PTC_Owner’s Manual Rev A_121911 VII. OPERATION 2. Battery Charge Level The joystick LED array is composed of ten (10) LED’s. ♦ Three (3) red ♦ Four (4) amber ♦ Three (3) green When all ten LEDs are lit continuously, there is a full charge on the batteries.
LiteRider PTC_Owner’s Manual Rev A_121911 VII. OPERATION Battery Gauge Flashes Rapidly (even with the joystick released) See figure 15. The control system safety circuits have operated and the control system has been prevented from moving the wheelchair.
LiteRider PTC_Owner’s Manual Rev A_121911 VII. OPERATION DIAGNOSTICS/TROUBLESHOOTING Below are a list of trouble-shooting actions. Try to use this list before you contact your Golden Technologies representative. Go to the number on the list which matches the number of flashing LEDs and follow the instructions.
LiteRider PTC_Owner’s Manual Rev A_121911 VII. OPERATION Slow or Sluggish Movement If the wheelchair does not travel at full speed or does not respond quickly enough, and the battery condition is good, check the maximum speed setting. If adjusting the speed setting does not remedy the problem, then there may be a non-hazardous fault.
LiteRider PTC_Owner’s Manual Rev A_121911 VII. OPERATION Maximum Speed/Profile Indicator Flashes This indicates the speed of the wheelchair is being limited for safety reasons. Contact your Golden Technologies representative NOTE: The VR-2 modules are not user serviceable.
LiteRider PTC_Owner’s Manual Rev A_121911 VII. OPERATION THERMAL ROLLBACK Your Lit eRider PTC is equipped with a safety system. A microprocessor monitors the operating temperatures of the controller. In the event of excessive heat occurring in the controller, the controller will decrease the speed of your chair.
LiteRider PTC_Owner’s Manual Rev A_121911 VIII. BATTERY CHARGING You must use only the charger that is supplied with your Lit eRider PTC. The use of any other charger on this power chair will void the warranty. Using unauthorized chargers may also result in severe damage to the batteries and/or damage to the chair.
LiteRider PTC_Owner’s Manual Rev A_121911 VIII. BATTERY CHARGING CHARGING THE BATTERIES Your Lit eRider PTC’s charging system is designed for your safety and for your convenience. Follow the steps below to recharge the batteries. 1. Position your Lit eRider PTC close to a standard wall electrical outlet.
LiteRider PTC_Owner’s Manual Rev A_121911 IX. CARE AND MAINTENANCE ROUTINE MAINTENANCE The Golden Lit eRider P TC is virtually maintenance free. All of the bearings are permanently lubricated and sealed.
LiteRider PTC_Owner’s Manual Rev A_121911 X. RIDING YOUR LiteRider PTC Control Through Tight Spots As you use your LiteRi der PTC to increase your mobility, you will undoubtedly encounter some obstacles that will require practice to negotiate smoothly and safely.
LiteRider PTC_Owner’s Manual Rev A_121911 X. RIDING YOUR LiteRider PTC Ramps Because of the American Disabilities Act (ADA), many buildings are fitted with ramps that provide access for power chairs and for other mobility vehicles. Please read and thoroughly understand “Safety Rules” and “Driving On An Incline” sections of this manual.
LiteRider PTC_Owner’s Manual Rev A_121911 XI. TECHNICAL SPECIFICATIONS Specification LiteRider PTC Model Number GP-160 Medicare Code N/A Weight capacity 275 lbs. Drive Wheels Rear Maximum speed 3.5 mph Operating Range 1 9.5 miles Ground Clearance 2.
LiteRider PTC_Owner’s Manual Rev A_121911 XI. TECHNICAL SPECIFICATIONS Specifications LiteRider PTC Model Number GP-160 Tires: Flat Free Front N/A Rear 9 in. Casters 6 in. Anti-Tip Wheels 3 in. Standard Seat: Stadium Style Slide Seat N/A Back Height (no headrest) 16.
LiteRider PTC_Owner’s Manual Rev A_121911 XII. WARRANTY Consumer Limited Warranty Power Wheelchairs The foll owing wa rranty is g ranted only to th e INITIAL Consumer who has purcha sed our pro duct and commences on the Date o f Purchase by the Consume r from an Auth orized Golden Tech nologies ’ P rovider.
LiteRider PTC_Owner’s Manual Rev A_121911 XII. WARRANTY Consumer Limited Warranty Power Wheelchair (continued) For the pe riod of thirte en months from t he date of pur chase, in the e vent of defe .
LiteRider PTC_Owner’s Manual Rev A_121911 WARRANTY/REGISTRATION FORM Golden Technologies Product Registration Form Please fill out this product registration form or you can also register your product online at www.goldentech.com. Failure to register your product may result in significant delays should service be required.
LiteRider PTC_Owner’s Manual Rev A_121911 Fold Here First Golden Technologies 401 Bridge St. Old Forge, PA 18518 Fold Here Second Place Stamp Here .
LiteRider PTC_Owner’s Manual Rev A_121911 .
LiteRider PTC_Owner’s Manual Rev A_121911 .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Golden Technologies GP160 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Golden Technologies GP160 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Golden Technologies GP160 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Golden Technologies GP160 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Golden Technologies GP160, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Golden Technologies GP160.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Golden Technologies GP160. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Golden Technologies GP160 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
