Manuale d’uso / di manutenzione del prodotto FT-160 del fabbricante Gemini Industries
Vai alla pagina of 17
It is of vital impor tance, bef ore attempting to operate y our engine, to read the general 'SAFETY INSTRUCTIONS AND W ARNINGS' section on pages 2-4 of this booklet and to strictly adhere to the advice contained therein.
2 Remember that your engine is not a " toy ", but a highly efficient internal-combustion machine whose power is capable of harming you, or others, if it is misused or abused. As owner, you, alone, are responsible for the safe operation of your engine, so act with discretion and care at all times.
4 Take care that the glow plug clip or battery leads do not come into contact with the propeller. Also check the linkage to the throttle arm. A disconnected linkage could also foul the propeller. After starting the engine, carry out any needle-valve readjustments from a safe position behind the rotating propeller.
6 ENGINE P AR TS NAME Rock er Cover Glow Plug Lock Nut Drive Hub Propeller W asher Crankcase Carburetor Exhaust Pipe Propeller Nut Cylinder Head Left (No .1) Cylinder Right (No .2) Cylinder Photo . 2 Aluminum tube Aluminum tube is not supplied with the engine.
8 It is essential that the firewall is strong and rigid (e.g. at least 15mm thick) and firmly integrated with the structure of the aircraft. INSTALLATION In the interests of scale appearance, the engine should be installed with the carburetor below the crankcase so that the exhaust pipes point downwards.
10 16x8, 18x6-8, 20x6 Carburetor The needle-valve and throttle lever locations are interchangeable by reversing the carburetor. This can be done as follows: Remove the carburetor carefully by unscrewing the two screws which secure both carburetor and choke valve.
12 GLOWPLUGS The role of the glo wplug Glowplug life Particularly in the case of very high performance engines, glowplugs must be regarded as expendable items. Install a plug suitable for the engine. Use fuel containing a moderate percentage of nitromethane unless more is essential for racing events.
14 Glowplug leads Fig.12 Switch should have sufficient capacity. The plug leads are fitted with special snap-on connectors that ensure firm contact with O.S. plug. They are a "click" fit and are not suitable for use with most other makes of glowplug.
16 Make sure that glowplugs are not connected to the battery. Do not heat the glowplugs while priming. (Fig.15). 2. Fig.15 Do not connect the battery to the glowplugs while priming. Open the throttle valve fully, close the choke valve and turn the propeller counter-clockwise through three revolutions.
18 Adjust the needle-valve 10. Abrupt adjustment of the needle-valve may cause the engine to stop, especially when it is new and insufficiently run-in. As the speed of the engine does not instantly change with needle-valve readjustment, small movements, with pauses between, are necessary to arrive at the optimum setting.
20 Start the engine. open the throttle fully . Adjust the neede-valve. Close the throttle gradually. Find the idling position. Fix the idling position. Open the throttle fully. Does the engine regain full power? Continue running at high speed for 5 seconds.
21 + Adjusting the mixture control v alve If the engine hesitates, puffing out a good deal of smoke, before picking up to full speed, it is probable that the idling mixture is too rich.
23 VALVE CLEARANCE ADJUSTMENT Remove the rocker cover from each cylinder head by unscrewing two socket-head cap-screws from the rocker box on top of the cylinder head with Allen key supplied. ALL O.S. four-stroke engines have their valve (tappet) clearances correctly set before they leave the factory.
25 Remove 0.04mm feeler, rotate prop through two revolutions and recheck gap. 5. If clearance is correct, loosen the locknut on the other rocker-arm and repeat steps 1 to 5 above. Finally, replace rocker box cover. 6. Remember: Excessive valve clearance will cause loss of power, due to valve (s) not opening sufficiently.
26 EXPLODED VIEW Type of screw C...Cap Screw M...Oval Fillister-Head Screw F...Flat Head Screw N...Round Head Screw S...Set Screw M3 C.M2.6x7 C.M3.5x20 C.
28 26381501 24981405 26381501 46481320 22781800 46481330 26381501 46481200 46281340 46481310 22781800 46481100 46281900 29081952 24981837 26381501 46181940 46181941 46181950 26711305 26781619 26681305 26681803 45581700 1 2 2-1 3 3-1 4 4-1 5 6 7 7-1 8 9 9-1 9-2 9-3 9-4 9-5 9-6 9-7 10 10-1 10-2 11 Description Code No.
30 13.26cc x 2 / 1.218cu.in. x 2 27.7mm / 1.091in. 22.0mm / 0.866in. 2.000-10.000r.p.m. 1,100g / 38.8oz. 23.5 50.5 63.5 4 -5.2 56.5 196 54 68 120 76 THREE VIEW DRAWING Dimensions(mm) Specifications Displacement Bore Stroke PracticalR.P.M. Output Weight C Copyright 2004 by O.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Gemini Industries FT-160 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Gemini Industries FT-160 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Gemini Industries FT-160 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Gemini Industries FT-160 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Gemini Industries FT-160, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Gemini Industries FT-160.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Gemini Industries FT-160. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Gemini Industries FT-160 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
