Manuale d’uso / di manutenzione del prodotto ZCG3500 del fabbricante GE Monogram
Vai alla pagina of 16
If you have questions , call 800.626.2000 or visit our website at: www .monogram.com Monogram. ® Installation Instructions Built-In Compactors Models: ZCG3500 ZCG3300 ZCG3100.
Before you begin—Read these instructions completely and carefully . IMPORT ANT: Save these instructions for local inspector’s use. IMPORT ANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES. NOTE TO INST ALLER: Be sure to leave these instructions with the Consumer .
3 Design Information Built-In Compactors Models available ZCG3500 SS Stainless steel built-in compactor ZCG3300 WW White built-in compactor ZCG3100 BB Black built-in compactor Note: This compactor is designed for built-in applications only .
4 Standard Appearance Panel Options The Monogram compactor models ZCG3300 and ZCG3100 come with a white/black reversible aluminum front drawer panel. Model ZCG3300 is shipped with the white panel showing and model ZCG3100 with the black side showing. The panels on both models can be reversed to reveal the opposite color side.
5 3/4" Thick W ood Panel with custom handle • Cut panel 12" wide x 25-13/16" high. A custom handle, of your choice, can be installed onto the 3/4" wood panel, replacing the standard handle. The cut edges of the custom panel can be seen and must be finished for best appearance.
6 T ools required: • #2 Phillips head screwdriver • Flat blade screwdriver • T ape measure • Spirit level • 10" long 2x4 • Adjustable wrench or slip joint pliers • Drill and 1/8&quo.
7 Installation in a corner If compactor is to be located in or near a corner of base cabinets, a minimum of 2" clearance from the corner is recommended. This is necessary to prevent adjacent cabinet door handles from inter fering with the compactor drawer .
8 Step 1 Determine toekick depth Place a section of the carton on the floor for protection. Lay the compactor on its back, supporting it with a piece of wood to prevent pressure on the power cord. Measure the toekick of an adjacent cabinet, from the front of the cabinet door to the front of the toekick (Dimension A).
9 Step 3 Positioning the compactor backstop A backstop should be installed to prevent the compactor from “ walking ” back when the drawer is closed. Measure and mark 16" back from the front edge of the cabinet toekick. Cut a 2x4, 10" long and anchor to the floor .
Compactor T op Countertop Overlap Step 5 Attach tip-over brackets Position tip-over brackets on the top of the compactor . Match hole #3 of the bracket to the screw hole on the compactor (the 3rd hole on the bracket is the standard location). Attach tip-over bracket to compactor with one slotted head screw on each side.
Step 5 (continued) If the countertop cannot be drilled into, slip the 90 ° clips over the short leg of the bracket and screw into the face of the cabinet. 11 T o install custom toekick (not supplied) measure the front of the compactor ’ s adjustable base and use those dimensions to cut out your custom toekick.
12 Step 7 Changing front panel (ZCG3300 and 3100 only) Remove compactor drawer by pulling it out until it stops. Then lift the drawer to clear second stop and remove drawer . Place drawer on its back. Procedure A Reverse color panel Remove the two screws in the bottom edge of the trim.
13 Procedure C (continued) • Lay drawer front face down on a flat sur face. • Remove 9 screws which retain the front panel and handle. – Save handle and galvanized inner door . – Discard front panel with side trim. • Place galvanized inner door onto the back side of the finished panel.
14 Procedure D 3/4" thick wood panel with custom handle • Pull the drawer out to stop position. • Unlatch the drawer front by opening the clasp on the right side. • While supporting the weight of the drawer front, remove the hinge pins on the left side.
15 Procedure D (continued) • T urn the panel over , appearance side up. Use wood blocks to support the inner door and prevent damage to the hinge and lock tabs. • Drill pilot holes through the front of the custom panel and through the metal panel to match the chosen handles.
Pub. No. 49-5778-4 Dwg. No. 165D4700P196 93042835C 10-03 JR Note: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram ® local ser vice in your area, call 800.444.1845. Note: Product improvement is a continuing endeavor at General Electric.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il GE Monogram ZCG3500 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del GE Monogram ZCG3500 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso GE Monogram ZCG3500 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul GE Monogram ZCG3500 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il GE Monogram ZCG3500, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del GE Monogram ZCG3500.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il GE Monogram ZCG3500. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo GE Monogram ZCG3500 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
