Manuale d’uso / di manutenzione del prodotto 49-60468-1 del fabbricante GE
Vai alla pagina of 20
Design Guide with Installation Instructions 36 ″ Built-In Bottom-Freezer Refrigerators monogram.com.
Safety Information Skill Level — Installation of this refrigerator requir es basic mechanical, carpentry and plumbing skills. Proper installation is the responsibility of the installer . Product failure due to improper installation is not covered under the GE Appliance Warranty.
36" Frame to Frame Width *84" From Floor to T op Frame 35" Case Width *83-1/2" at Rear 25-3/8" Framed Models 25-3/4" Stainless Steel Models Case Depth Depth Including Han.
1/4" 1/2" 3/4" 1" 1-1/4" 1" 3/4" Overlay Panel (Nominal Size) Stainl ess Steel 1/4" 1/2" 3/4" 2" 1-1/4" 1-1/2" 1-3/4" 3" 2-1/.
1/4" 1/2" 3/4" 1" 1-1/4" 1/4" 1/2" 3/4" 1" 1-1/4" 1-1/2" 23-7/8" From Rear of Refrigerator 3/4" Overlay Panel (Nominal Size) Case T rim.
CUST OMIZA TION BASICS: Framed Or Overlay Panels, Cust om Handles and Accessory Kits Overlay panels Y ou may also choose to install custom overlay panels from your cabinet manufacturer . This design provides a seamless appearance which integrates smoothly with surrounding cabinetry.
1/4 ″ FRAMED P ANEL DIMENSIONS 7 If you choose to install framed panels, they must be cut to the dimensions shown. The panels will slide into the frame on the door , drawer and grille.
*84" 2-9/16" 24" *3" to 4" 3/16" 1-7/8" Design Guide 8 SIDE P ANELS Side panels must be used whenever the sides of the refrigerator will be exposed. The 1/4 ″ side panels will slip into the side case trim. Secure the panels to the refrigerator with stick-on hook and loop fastener strips.
Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet . DO NOT , UNDER ANY CIRCUMST ANCES, CUT OR REMOVE THE THIRD (GROUND) PR ONG FROM THE P OWER CORD.
STEP 1 REMOVE P A CKA GING CA UTION: Refrigerator is much heavier at the top than at the bottom—be careful when moving. When using a hand truck , handle from side only. PRUDENCE: Le réfrigérateur est beaucoup plus lourd en haut qu’en bas. Il faut être prudent lors des déplacements.
Block Soffit Side View Height From Floor to Bottom of Wood Block Brackets Required Brackets Not Required Beneath a Soffit 11 STEP 2A W A TER LINE INST ALL A TION WITH A RE VERSE OSMOSIS SYSTEM Skip th.
12 STEP 5 LE VEL REFRIGERA T OR All models have 4-point leveling. The front is supported by leveling legs, the rear is suppor ted by adjustable wheels. Both are accessible from the front of the refrigerator . • To level the back of the refrigerator , turn the 7/16 ″ hex nut located above the front wheels.
STEP 8 AD JUST DOOR SWING NO TE: This refrigerator has a 2-position door stop. When space does not allow the door to swing open fully to 130°, you may change the door swing to a 90° opening. Skip this st ep if door opening is satisfactory for your installation situation.
14 STEP 10 INST ALL 1/4 ″ FRAMED P ANELS • There are two sets of holes in the handle side trim. Replace handle side trim by installing the original screws in the FR ONT screw holes. • Secure the handle to the door using the RE AR screw holes. • Follow the same procedures to install the drawer panel.
15 STEP 10A INST ALL OVERL A Y P ANELS • There are two sets of holes in the handle side trim. Replace handle side trim by installing the original screws in the RE AR screw holes. • Secure the handle to the door using the FRONT screw holes. • Follow the same procedures to install the drawer panel.
16 STEP 11 CONNECT W A TER SUPPL Y • Locate and bring tubing to the front of the cabinet . • Turn the water on to flush debris from line. Run about a quar t of water through tubing into a bucket , then shut off water . Copper Tubing: • Slip a 1/4 ″ nut and ferrule (provided) over both ends of the copper tubing.
17 Installation Instructions STEP 14 INST ALL TOEKICK • Locate the supplied toekick (shipped taped to the side of the refrigerator). Install with 2 screws provided, adjust to desired height and tighten screws. • A custom toekick can be installed to match or complement the surrounding cabinetry.
18 Notes.
19 Notes.
NOTE: While per forming installations described in this book , safety glasses or goggles should be worn. For Monogram ® local ser vice in your area, call 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il GE 49-60468-1 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del GE 49-60468-1 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso GE 49-60468-1 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul GE 49-60468-1 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il GE 49-60468-1, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del GE 49-60468-1.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il GE 49-60468-1. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo GE 49-60468-1 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
