Manuale d’uso / di manutenzione del prodotto FELCOM 500 del fabbricante Furuno
Vai alla pagina of 66
w w w. furuno.c o .jp All brand and product n ames are trademarks, regi stered trad emarks or service m arks of their respective holders. Installation Manual INMARSAT FL EETBROADBAND FELCOM 250/ FELCOM 500 SAFETY INSTRUCTIONS ........ ................
The paper used in this manual is elemental chlorine free. ・FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN Telephone : +81-(0)798-65-2111 Fax : +81-(0)798-65-4200 A : AUG 2009 . Printed in Japan All rights reserved.
i SAFETY INSTRUCTIONS Do not open the equipment unless totally familiar with electrical circuits and service manual. Only qualified personnel should work inside the equipment. Do not approach the radome closer than 1.4 m (FELCOM 500) or 0.7 m (FELCOM 250) when it is transmitting.
ii SYSTEM CONFIGURATION Antenna unit FB-1500 (FELCOM 500) FB-1250 (FELCOM 250) Communication unit FB-2000 IP Handset FB-8000 Incoming indicator FB-3000 Network Equipment G3 facsimile Analog telephone .
iii EQUIPMENT LISTS Standard Supply *: See lists at the back of thi s manual. Option al Su pply Name Type Code N o. Qty Remarks Anten na unit FB-1500 - 1 For FELC OM 500 FB-1250 - For F ELCOM 250 Comm.
EQUIPME NT LISTS iv Connec tor CP03-289 01 008-542 -460 Modula r conn ector MPS 588-C2 pcs for LAN ca ble LAN cable MOD-Z 072-02 0+ 000 -167-175 -10 2 m, modul ar plug for both ends MOD-Z072- 050+ 000.
1 1. HOW TO INSTALL THE UNIT 1.1 Ant enna Unit Gen eral Interfer ing objects (especiall y metal o bjects l ike masts) near the ante nna can, i n the worst case, prevent r eception or transmission. Further, RF radiati on from the ant enna will af fect the human body.
1. HOW TO INSTALL THE UNIT 2 Locate awa y from passengers and crew Radio waves can be harmful to the human body. Beca use safe distances change by co untry and ship construct ion, there is no standar d formula to calculate saf e distance. However, be low are general guidelines .
1. HOW TO INSTALL THE UN IT 3 • FELCOM 250: Personnel shoul d not approa ch an area in which the ra diation level is higher than 10 W/m2, i.e., withi n 0.70 m from the radome surface. Construct a protecti ve fence around t he antenna u nit so t hat personnel can not appr oach the antenna unit within 0.
1. HOW TO INSTALL THE UNIT 4 Compass safe distance Locating the antenna unit t oo close to a compass can affect t he compass performa nce. Keep the compass safe distance t o prevent interfere nce to the magnetic compass.
1. HOW TO INSTALL THE UN IT 5 Antenna mast an d mounting base To get the best performanc e from the antenna electroni cs and mechanics, the antenna must be install ed properly on a speciall y designed mast with sui table flange and rubber gask et. Below are guidelines for instal lation of the mounting mast and mounting bas e.
1. HOW TO INSTALL THE UNIT 6 FELCOM 500: H ow to insta ll the antenn a unit Carefully unpack the radome and check for damage. Antenna unit installat ion materi als Procedur e 1. Loosen four lifting lugs and turn t hem to outsid e at the bot tom of the radome as shown in the figure on the next page.
1. HOW TO INSTALL THE UN IT 7 5. L ay the rubber mat on the mounting base and p ut the antenna un it on the rubber mat , keeping in mind cable glan d direction (s tandard direction is stern). 6. Fix th e antenna unit with four sets of hexagonal bolts and nuts as shown on the next page.
1. HOW TO INSTALL THE UNIT 8 9. Restore the lifting lugs to their original po sitions. FELCOM 250: How to install the antenna unit Carefully unpack the radome and ch eck for damage.
1. HOW TO IN STALL THE UNIT 9 Procedure 1. Attach the rubber mat on the bottom of the antenna unit if the mat is supplied as the insta llation material.
1. HOW TO INSTALL THE UNIT 10 9. Coat all bolts and nuts with silicone seal ant to preve nt electrolyt ic corrosion as shown below. Note: The cable ent ry hole ( φ 60) at the bottom of the antenna functi ons as ventilatio n hole, allowin g trapped moisture to escape the dome.
1. HOW TO INSTALL THE UN IT 11 How to mount the FELCO M 250 antenna unit with optional pole moun t kit Pole mount ki t: Type OP16-52, Code number 00 0-017-061 1.
1. HOW TO INSTALL THE UNIT 12 1.2 Communicati on Unit Select a l ocation for the communicat ion unit ( CU) by fol lowing the i nformation shown below. • The uni t is no t waterpro of. Keep the uni t away from water splas h. • Keep th e unit away from direct sun light.
1. HOW TO INSTALL THE UN IT 13 1.3 IP Hands et The IP handset functions as a displ ay and it may also be used for normal voice commun ication. The units (max 26 units) may be instal led anyw here onboard the vessel. The IP handset is pro- vided with a cradle.
1. HOW TO INSTALL THE UNIT 14 1.4 Incoming Indicator (o ption) Select a l ocation f or the inco ming indica tor by f ollowing the informati on shown below. • Keep th e unit away from water splash . • Keep th e unit away from direct sun light. • Set the unit away from the exh aust pipes and vents.
1. HOW TO INSTALL THE UN IT 15 4. Fix the case wi th four M4x8 screws (suppl ied) t o the flush mount plate. 5. Pass the cabl e from the CU through the bottom of the case. 6. Con nect the cable to the port on the lid. 7. Atta ch the cabl e fixture (supplied) with two screws.
1. HOW TO INSTALL THE UNIT 16 1.5 Fa csimile FAX-2820 (Opt ion) Note: The hook s supplied are not used in the i nstallatio n. 1. Lay the facsimi le on the top of the mounting plate. 2. Align right si de and rear with the projecti on on the mounting plate.
1. HOW TO INSTALL THE UN IT 17 4. Atta ch the compass safe distance label at the location shown below. How to change mod em settings 1. Press [Menu/set], [* ], [2], [ 8], [6] an d [4] keys i n this sequen ce to enter the mai ntenance mode. The fax machine beeps for approximately one se cond and displays "MAINTENANCE" on the LCD.
1. HOW TO INSTALL THE UNIT 18 How to mount The mounting d imensions are sh own in the outline drawi ng at the back of this manual. Deter mine the mounting loca- tion, leaving suf ficient space around the unit, and then fix the mounti ng base to the mounting locat ion.
1. HOW TO INSTALL THE UN IT 19 1) Remove the plastic sheet and recor ding sheet. 2) Set #1 DIP switch to ON ( PB side). 3) Reattach t he plasti c sheet and re cording sheet.
20 2. CONNECTIONS 2.1 Standard Conn ection Run and connect cabl es, refering to the figure be low and the int erconnection diagram ( page S-1). ALARM NMEA RS-232C LAN ANT 12 34 TEL 12 34 12-24 VDC 12-.
2. CONNECTIONS 21 2.2 Ant enna Cab le Run the ante nna cable ( coaxial ca ble 8D-FB-CV, 30 m, 40 m o r 50 m supplie d) betwee n the an- tenna unit and communication unit . At tach the connect or plug of the antenna cable to the antenna unit. Conne ct the coa xial connec tor (8D-FB- CV) to th e other end of the an tenna cable.
2. CONNECTIONS 22 How to attach the an tenna cable connecto r N-P-8DFB-CF Attach the coaxial plug (supplie d) to the other end of the coaxial cable to connec t to the CU as follo ws. Outer Sheath Armor Inner Sheath Shield ( Dimensions in millimeters.) 50 30 Cover with heat-shrink tubing and heat.
2. CONNECTIONS 23 How to attach the an tenna cable connecto r N-SP-12DSFA-CF If the opti onal coaxial cabl e 12D-SFA-CV (100 m) is used, at tach the optional coaxial plug N-SP- 12DSFA-CF as follows. Outer Sheath Armor Inner Sheath Shield Dimensions in millimeters.
2. CONNECTIONS 24 2.3 Communicati on Unit Telephon e FC755D1 and Facsimile FA X-2820 Connect the cable from the telephone o r facsimile to TEL1, 2, 3 or 4 port of t he communication unit. The modular connector can be connected d irectly to the TEL1 or TEL 2 as shown in the fig- ure below.
2. CONNECTIONS 25 TTYCS-1 Cable fabric ation NMEA signal, External alarm Approx. 50 6 Cut armor and sheath. T aping 10 Crimp-on lug FV1.25 Procedure to insert wire 1. T wist core. 2. Push spring-loaded catch with slotted-head screwdriver . 3. Insert core into hole.
2. CONNECTIONS 26 Cable fixture To connect t he LAN and TEL l ines, atta ch the cable f ixture (supplied) t o the rear pa nel of t he com- municati on unit. Then in sert the conne ctors to each port . Fasten each cable with a cabl e tie (sup- plied) to the cabl e fixture.
2. CONNECTIONS 27 2.4 Not ice for network c onnec tion With a hub(s), FELCOM500/FELCOM250 can establ ish a network configurati on. If the hub(s) is connected in loop form , the FELCOM500/FELCOM250 may not function normally .
2. CONNECTIONS 28 2.5 Desktop Install ation of Communica tion Unit to - comply with IPX2 (dripping) standard How to inset the grommet Be sure to install the Communication Unit to a desktop to protec t from dripping. Aft er installing , affix the grommets over the mounting screws.
2. CONNECTIONS 29 3. With t he connector cover rail in the slot, rais e the connector c over in the direct ion of the arrow as shown bel ow. 4. Push t he connector cover in towar ds the triangle mark on the ce nter top of t he Communicatio n Unit to a ffix.
2. CONNECTIONS 30 2.6 LAN Cabl e Fabricati on Fabricate an optional LAN cable (FR-FTPC-CY 10, 20, 30, 50 or 100 m) as follows. Cut ar mor and outer vinyl shea th as shown below and then connect the modular connector MPS588-C (optio n) to both ends.
31 3. SETTING AFTER INSTALLATION This chapter shows how to enter basic settings, done by the installation tech nician. For the net- work setting, request to an administrato r of the ship network.
3. SETTING AFTER INSTAL LATION 32 The browser starts and the main menu of the Web software in the FELCOM 250/500 opens. 7. Click the Administrator Logi n button on upper right hand sid e on the screen.The Logi n win- dow opens. 8. Key in username "Admin" and passwor d "01234567"(def ault value).
3. SETTING A FTER INSTALLA TION 33 10. Click Sett ings on the menu bar. The sub menu appears on left side and current setting appears in the Information wind ow on right si de.
3. SETTING AFTER INSTAL LATION 34 3.2 GPS Setting 1. Click GP S on t he Basic s ettings sub menu. 2. If an external GPS is co nnected to the NMEA port on the communication unit, set the baud rate t o 4800 bps or 38400 bps ac cording t o the GPS connect ed.
3. SETTING A FTER INSTALLA TION 35 3.3 Analog Port Settin g Set for analog tel ephones/faxes that are connec ted to the TEL ports as foll ows. 1. Cli ck Analog ports on the Basic sett ings sub menu. 2. In the Type box, select the equipment that is connected to the TEL port.
3. SETTING AFTER INSTAL LATION 36 3.4 Incoming Indicator Se tting If the optional Incomi ng Indicat or is connect ed, set it as fol lows. 1. Click Incomin g Indica tor in t he Basic s ettings s ub menu.
3. SETTING A FTER INSTALLA TION 37 3.5 Serial Port Sett ing Set for the equipment t hat is connected to the RS-232C por t. 1. Cli ck Serial por t in t he Basic s ettings s ub menu. 2. Select a baud r ate from the Bau d rate dr op-down list. The selection s are 9600, 19200, 38400, 57600 and 115 200 bps.
3. SETTING AFTER INSTAL LATION 38 3.6 Satellite Setting The three satellites are named APAC (Asia- pacific), EMEA (Europe-Middle east -Africa) and AMER (America). To change sat ellite name, do as foll ows. 1. Click Satellit e in t he Basic se ttings s ub menu.
3. SETTING A FTER INSTALLA TION 39 3.7 OTA Setting OTA stands for Over The Air. The OTA function permits remote management of files in the SIM card. 1. Cli ck OTA in the Basic sett ing sub menu. 2. To enable the OTA, click the Enabled radio but ton. To disable the OTA, click t he Disabled ra- dio button.
3. SETTING AFTER INSTAL LATION 40 3.8 Han dset Setting To use the IP handset, set the Web software and the IP handset as fol lows. Web softwar e setting 1. Click Se ttings i n the menu bar. 2. Click PBX Sett ings in the Settings sub menu at the left side of the screen.
3. SETTING AFTER INS TALLATION 41 Setting in the IP handset 1. Push the Enter key at the idle screen to show the main men u. 2. Push 6 to select the Settings ico n and then push the Enter key to show the Settings menu. 3. Push 3 key to show the SIP menu.
3. SETTING AFTER INSTALLATION 42 5. With the Phone number box high lighted in blue, push the Enter key to show the phone num- ber input screen. 6. Enter the extension number tha t is registered in the Web software and push the Enter ke y. If something has been registered, push the CLR key to erase it.
3. SETTING A FTER INSTALLA TION 43 These handsets can b e used for communication. However, t he foll owing screen d oes not update automatically . Press t he Reload button of the b rowser to ref resh the screen.
AP-1 APPENDIX 1 JIS CABLE GUIDE D T M TT PY C YS -S 3. Sheath Type 4. Armor Type 5. Shielding Type 6. Core Sheath Ethylene Propylene 2. Insulation Type 1.
0#/' 176.+0' 36; &'5%4+26+10%1&'ͳ 㧼㧭㧯㧷㧵㧺㧳ޓ㧸㧵㧿㨀 #3: ($ #, 'ޔ$ ,' 0#/' 176.
%1&'01 6;2' %2 ⇛ޓޓ࿑ 176.+0' ฬޓޓ⒓ 0#/' ᢙ㊂ 36; ↪ㅜ㧛⠨ 4'/#4-5 ⇟ภ 01 ဳฬ㧛ⷙᩰ &'5%4+2 6+105 +056#.
㧼㧭㧯㧷㧵㧺㧳ޓ㧸㧵㧿㨀 #4: ($ 0#/' 176.+0' &'5%4+26+10%1&'ͳ 36; ࡙࠾࠶࠻ 70+6 㨻㩧㩍㩏㩟㩐㨹㩎 #06'00#70+6 ($ Ꮏ᧚ᢱ +056#.
%1&'01 6;2' 12 ⇛ޓޓ࿑ 176.+0' ฬޓޓ⒓ 0#/' ᢙ㊂ 36; ↪ㅜ㧛⠨ 4'/#4-5 ⇟ภ 01 ဳฬ㧛ⷙᩰ &'5%4+2 6+105 㩝㩆㩨㨷㩡㨺㩄㨺㩎㩨 #(: ('.
%1&'01 6;2' 52 +6'/ 01 0#/'1( 2#46 176.
.
8/Mar/10 R.Esumi D-1.
11/Dec/09 R.Esumi D-2.
17/May/2010 TAKAHASHI D-3.
17/May/2010 TAKAHASHI D-4.
11/May/09 R.Esumi D-5.
18/Feb/09 R.Esumi D-6.
18/Feb/09 R.Esumi D-7.
Y. Hatai D-8.
Feb.15'06 T.Matsuguchi D-9.
$ # & % 0#/' ฬ⒓ 6+6.' MI /#55 &9) 0Q 5%#.' #22418'& %*'%-'& &4#90 4'(0Q +06'4%100'%6+1 0 &+#)4#/ ⋧⚿✢࿑ ࠗࡦࡑ࡞ࠨ࠶࠻ࡈ࠻ࡉࡠ࠼ࡃࡦ࠼ +0/#45#6 (.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Furuno FELCOM 500 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Furuno FELCOM 500 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Furuno FELCOM 500 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Furuno FELCOM 500 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Furuno FELCOM 500, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Furuno FELCOM 500.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Furuno FELCOM 500. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Furuno FELCOM 500 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
