Manuale d’uso / di manutenzione del prodotto Ethernet Blaster Communications Cable del fabbricante Altera
Vai alla pagina of 35
101 Innovation Dr ive San Jose , CA 9513 4 www .altera.com EthernetBlaster Co mmunications Cable User Guide Software Version: 80 Document Version: 1.1 Document Da te: July 2008.
Copyright © 2008 Altera Corpo ration. All rights reserved. Altera, The Programmable Solutions Compan y, the stylized Altera logo, specific device designations, and all other words and logos that are ide ntified as trademarks and/ or service marks ar e, unless note d ot herwise, the tradem arks and service marks of Altera Corporation in the U.
© July 2008 Altera Corporat ion EthernetBlaster Communi cations Cable User Guide Contents Chapter 1. About the Ethe rnetBlaster Communication s Cable Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iv EthernetBlaster Co mmunications Cable User Gui de © July 2008 Altera Corporation.
List of Figures v © July 2008 Altera Corporat ion EthernetBlaster Communi cations Cable User Guide List of Figures Figure 1–1: EthernetBlas ter Communications Cable Ethernet Port, Targ et Port, and Base Views . . . . . . 1-3 Figure 1–2: Remote Connection via Network .
vi List of Figure s EthernetBlaster Co mmunications Cable User Gui de © July 2008 Altera Corporation.
List of Tables vii © July 2008 Altera Corporat ion EthernetBlaster Communi cations Cable User Guide List of T ables Table 1–1: Status LED Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
viii List of Tables EthernetBlaster Co mmunications Cable User Gui de © July 2008 Altera Corporation.
© June 2008 Altera Corporatio n EthernetB laster Communi cations Cable User Guide 1. About the EthernetBlaster Communications Cable Introduction The EthernetBlaster communica tions cable connects to a standard Ethernet network port with an RJ-45 connector .
1–2 Chapter 1: About the Ethe rnetBlas ter Communication s Cable Introduction EthernetBlaster Co mmunications Cable User Gui de © June 2008 Altera Corporation The EthernetBlaster V CC(T A RGET) pin must be connected to the appr opriate voltage for the device being programmed.
Chapter 1: About the EthernetBlaster Commu nications Cable 1–3 Introduction © June 2008 Altera Corporatio n EthernetB laster Communi cations Cable User Guide The status LED on the tar get port side of th e cable displays the operation status of the EthernetBlaster communi cations cable.
1–4 Chapter 1: About the Ethe rnetBlas ter Communication s Cable Cable Setup EthernetBlaster Co mmunications Cable User Gui de © June 2008 Altera Corporation 1 Refer to your operating system manual or contact your network administrator to verify that your networ k supports DHCP services and for instru ction on how to change your IP addr ess.
Chapter 1: About the EthernetBlaster Commu nications Cable 1–5 Cable Setup © June 2008 Altera Corporatio n EthernetB laster Communi cations Cable User Guide 3.
1–6 Chapter 1: About the Ethe rnetBlas ter Communication s Cable Cable Setup EthernetBlaster Co mmunications Cable User Gui de © June 2008 Altera Corporation 1 Always connect the network patch cable as instr ucted in step 2 before connecting the power cord.
Chapter 1: About the EthernetBlaster Commu nications Cable 1–7 Cable Setup © June 2008 Altera Corporatio n EthernetB laster Communi cations Cable User Guide 1 Refer to your operating system manual or contact your network administrator for instruction on how to change your IP address.
1–8 Chapter 1: About the Ethe rnetBlas ter Communication s Cable Cable Setup EthernetBlaster Co mmunications Cable User Gui de © June 2008 Altera Corporation 2.
Chapter 1: About the EthernetBlaster Commu nications Cable 1–9 Cable Setup © June 2008 Altera Corporatio n EthernetB laster Communi cations Cable User Guide 3.
1–10 Chapter 1: About the Et hernetBla ster Communicat ions Cable Cable Setup EthernetBlaster Co mmunications Cable User Gui de © June 2008 Altera Corporation Configuring the EthernetBlaster Hardware to Use Static IP Addressing By default, the Eth ernetBlaster communica tions cable is factory configur ed to use dynamic IP addr essing.
Chapter 1: About the EthernetBlaster Communications Cable 1–11 Cable Setup © June 2008 Altera Corporatio n EthernetB laster Communi cations Cable User Guide Configuring the EthernetBlaster Hardware.
1–12 Chapter 1: About the Et hernetBla ster Communicat ions Cable Cable Setup EthernetBlaster Co mmunications Cable User Gui de © June 2008 Altera Corporation Setting Up the EthernetBlaster Hard ware in the Quartus II Software Use the following steps to set up the Et hernetBlaster communica tions cable in the Quartus II software.
Chapter 1: About the EthernetBlaster Communications Cable 1–13 Cable Setup © June 2008 Altera Corporatio n EthernetB laster Communi cations Cable User Guide 1 The EthernetBlaster communi cations cable supports the Joint T est Action Group (JT AG), Passive Serial Pr ogra mming, and Active Serial modes.
1–14 Chapter 1: About the Et hernetBla ster Communicat ions Cable Cable Setup EthernetBlaster Co mmunications Cable User Gui de © June 2008 Altera Corporation.
© June 2008 Altera Corporatio n EthernetB laster Communi cations Cable User Guide 2. EthernetBlaster Communications Cable Administration Introduction This chapter describes how to administer your Eth.
2–2 Chapter 2: EthernetBlaster Communi cations Cable Administ ration Managing Passwords EthernetBlaster Co mmunications Cable User Gui de © June 2008 Altera Corporation 2.
Chapter 2: EthernetBlaster Commun ications Cable Administra tion 2–3 Resetting the Hardware © June 2008 Altera Corporatio n EthernetB laster Communi cations Cable User Guide 3. Enter the new Quartus II r emote connection password in the New Password field and again in the Confirm New Password field.
2–4 Chapter 2: EthernetBlaster Communi cations Cable Administ ration Firmware Upgrade EthernetBlaster Co mmunications Cable User Gui de © June 2008 Altera Corporation 1 When the ErthenetBlaster is .
Chapter 2: EthernetBlaster Commun ications Cable Administra tion 2–5 Firmware Upgr ade © June 2008 Altera Corporatio n EthernetB laster Communi cations Cable User Guide 3. Cl ick Browse and then locate and select the fi rmwar e file on your system.
2–6 Chapter 2: EthernetBlaster Communi cations Cable Administ ration Firmware Upgrade EthernetBlaster Co mmunications Cable User Gui de © June 2008 Altera Corporation.
© June 2008 Altera Corporatio n EthernetB laster Communi cations Cable User Guide 3. EthernetBlaster Communications Cable Specifications Overview This chapter provides compr ehensive information abou.
3–2 Chapter 3: EthernetBlaster Commu nications Cable Spec ifications EthernetBlaster Hardware Connections EthernetBlaster Co mmunications Cable User Gui de © June 2008 Altera Corporation EthernetBlaster Ethernet Jack Connection The Ethernet cable Ethernet jack connect s to the EthernetBlaster communications cable Ethernet port.
Chapter 3: EthernetBlaster Commun ications Cable Sp ecifications 3–3 Operating Cond itions © June 2008 Altera Corporatio n EthernetB laster Communi cations Cable User Guide 1 The circui t boar d must supply VCC( T ARGET) and ground to the EthernetBlaster cable for the I/O drivers.
3–4 Chapter 3: EthernetBlaster Commu nications Cable Spec ifications Operating Conditio ns EthernetBlaster Co mmunications Cable User Gui de © June 2008 Altera Corporation I I Input current TDO or dataout –10.0 10.0 mA I o Output current TCK , TMS , TDI , nCS , nCE –10.
© June 2008 Altera Corporatio n EthernetB laster Communi cations Cable User Guide Info. Additional Information Referenced Documents For more information on configuration and in-system pr ogrammabili ty (ISP), see the following sour ces: ■ AN 39: IEEE 1 149.
Info–2 Chapter Info: Additional Informatio n Revision History EthernetBlaster Co mmunications Cable User Gui de © June 2008 Altera Corporation Revision Histor y The table below displays the revision history for the chapters in this user guide.
Chapter Info: Additional Info rmation Info–3 Typographi c Conventions © June 2008 Altera Corporatio n EthernetB laster Communi cations Cable User Guide Italic type Internal timing para meters and variables are shown in ita lic type. Examples: t PIA , n + 1.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Altera Ethernet Blaster Communications Cable è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Altera Ethernet Blaster Communications Cable - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Altera Ethernet Blaster Communications Cable imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Altera Ethernet Blaster Communications Cable ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Altera Ethernet Blaster Communications Cable, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Altera Ethernet Blaster Communications Cable.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Altera Ethernet Blaster Communications Cable. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Altera Ethernet Blaster Communications Cable insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
