Manuale d’uso / di manutenzione del prodotto SPX-F17M del fabbricante Alpine
Vai alla pagina of 20
SPX- F17M Component 2-way Single Channel Speaker System/ Paire de haut-parleurs à canal unique OWNER’S MANUAL Please read before using this equipment MANUEL DE L'UTILISA TEUR V euillez lire le présent manuel avant la mise en service du matériel ALPINE ELECTRONICS, INC.
2 Attention UTILISER LES ACCESSOIRES SPECIFIES ET LES INS T ALLER CORRECTEMENT . L ’utilisation d’autres pièces non désignées risque de provoquer des dommages à l’intérieur de l’appareil ou son installa- tion risque de ne pas être faite correctement, et les pièces desserrées peuvent provoquer des dangers.
3 19. Screw st4.2x9.5mm / Vis st4.2x9.5 mm …………….......………. x1 20. Screw st4.2x19mm / V is st4.2x19 mm ...………………...……… x2 21. Screw st4.2x19mm / V is st4.2x19 mm .........……………………… x1 22. Wing nut M4 / Écrou à oreilles M4 .
4 T abel of Contents Installation W oofer .......................................................................................... 5 T weeter ........................................................................................ 7 Crossover Network.
5 Installation W oofer: Surface mount Notes: l Attach gasket tape as shown, then lock speaker into grille ring. l If spacer ring is used with grille, snap-fit tabs on spacer ring must be removed for proper fit. st4.2x25mm W oofer: Flush mount Notes: l Attach gasket tape as shown.
6 Installation W oofer: Factory/OEM custom fit Notes: l Attach gasket tape as shown. l Use appropriate adapter pattern for OEM fit, then break away any unused tabs. st4.2x25mm W oofer: Factory/stealth Notes: l Attach gasket tape as shown. st4.2x25mm Hardware: l Use st4.
7 Installation W oofer: Factory/Size-down Notes: l Attach gasket tape as shown. l Use appropriate adapter pattern for OEM fit, then break away any unused tabs.
8 T weeter: Flush mount Notes: l Pass wires through terminal cover and connect to terminals. l Press terminal cover snuggly over tweeter housing, making sure connections are not exposed. l Attach mounting spring, adjusting screw depth and spring tension as needed.
9 Notes: l Remove network cover , and secure base as shown. l Connect wires to terminal blocks accordingly . (see System Connection Diagrams section) l Make appropriate jumper settings using jumper puller tool. (see Crossover Network Settings section) l Re-secure network cover .
10 Crossover Network Settings Introduction Configuration du filtre de voies Introduction Phase relationships are critical to driver interaction and the perception of realism. Crossovers must be designed around actual speaker placement to avoid cancellation and response aberrations.
11 Crossover Network Settings Configuration du filtre de voies Jumper Group Function Please read the following pages carefully to determine which network configuration is most appropriate for your particular installation.
12 Crossover Network Settings System T ype 1 Speaker Placement Description: In this system type, woofer and tweeter are mounted close together at an equal distance from the listener . Configuration A is the default setting of the network, but assumes essentially on axis positioning.
13 Crossover Network Settings System T ype 1 Filter Description: In this system type, both woofer and tweeter are equidistant from the listening position and mounted close together . While the kick-panel is one of the more common locations to achieve this, it is certainly not the only one.
14 Crossover Network Settings System T ype 2 Speaker Placement Description: In this system type , w oofer and tweeter are mounted at diff erent locations and at diff erent distances from the listener .
15 Crossover Network Settings System T ype 2 Filter Description: In this system type, both woofer and tweeter are mounted apart at dif ferent distances and angles relative to the listening position, with the tweeter as the closest driver .
16 Crossover Network Settings System T ype 3 Speaker Placement Description: In this system type, woofer and tweeter are mounted close together on the dashboard, rear deck, or other surface that presents an oblique angle to the listener .
17 Crossover Network Settings System T ype 3 Filter Description: Despite the fact that both drivers are mounted in the same plane and in close proximity in this system type, their orientation results in the acoustic center of the tweeter being farther away .
18 Crossover Network Settings System T ype 4 (Fully/Partially Active) Speaker Placement Description: In this system type , some le vel of e xter nal signal processing is a vailable , allo wing use of the network in a par tially or ev en fully active mode.
19 Crossover Network Settings System T ype 4 Filter Description: Fully active systems have often been considered to be the most flexible, but they are certainly not the most effective in all cases.
System T ype Component 2-wa y speaker P ower Handling (peak/RMS) 300/75W Impedance 4 W F requency Response 30-35 kHz Net W eight 2.5 kg Drivers General Speaker siz e 6,5” 28 mm Speaker T ype Woofer/Midrange T w eeter P ower Handling (RMS) 75 W 150 W V oice Coil Impedance (nom) 4 W 4 W F requency Response (-10dB) 10 kHz >40 kHz Sensitivity (@2.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Alpine SPX-F17M è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Alpine SPX-F17M - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Alpine SPX-F17M imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Alpine SPX-F17M ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Alpine SPX-F17M, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Alpine SPX-F17M.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Alpine SPX-F17M. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Alpine SPX-F17M insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
