Manuale d’uso / di manutenzione del prodotto 1999 Explorer del fabbricante Ford
Vai alla pagina of 264
Before driving Introduction 2 Instrumentation 4 Controls and features 19 Seating and safety restraints 113 Starting and driving Starting 139 Driving 144 Roadside emergencies 175 Servicing Maintenance and care 195 Capacities and specifications 243 Customer assistance 252 Reporting safety defects 264 Index 265 All rights reserved.
ICONS Indicates a safety alert. Read the following section on W arnings. Indicates vehicle information related to recycling and other environmental concerns will follow . Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment.
INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation. SPECIAL NOTICES Notice to owners of utility type vehicles Before you drive your vehicle, please read this Owner’ s Guide carefully .
OFF RSM SET ACC COAST OFF ON C 0 1 2 3 4 5 6 RPMx1000 ABS ! CHECK ENGINE FUEL RESET E F H H H SPEED CONT O/D OFF L L 10 MPH 20 50 60 70 30 40 80 90 km/h 0 0 0 10 1 00 1 20 1 0 0 0 0 0 0 40 60 80 100 120 140 160 180 20 DOOR AJAR CHECK GAGE CHECK SUSP * if equipped Instrument cluster (pg.
PUSH OD ON/OFF 4WD LOW OFF ON R. WIPE FF REW SIDE 1 - 2 BASS TREB BAL FADE TAPE AMS AM FM CD CLK VOL - PUSH ON SHUFFLE COMP CD EJ CD SCAN DISCS TUNE SEEK 3 2 14 5 6 OFF A/C MAX A/C Gearshift (includes overdrive button) (pg. 152) Electronic sound system (pg.
W ARNING LIGHTS AND CHIMES Check engine Y our vehicle is equipped with a computer that monitors the engine’ s emission control system. This system is commonly known as the On Board Diagnostics System (OBD II). This OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards.
3. The fuel cap may not have been properly installed and securely tightened. These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel and/or properly installing and securely tightening the gas cap.
Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter . Brake system warning Momentarily illuminates when the ignition is turned to the ON position and the engine is off.
High beams Illuminates when the high beam headlamps are turned on. Anti-theft system (if equipped) Refer to SecuriLock y passive anti-theft system in the Controls and features chapter . Charging system Illuminates when the ignition is turned to the ON position and the engine is off.
Four wheel drive high (if equipped) This light momentarily illuminates when the ignition is turned to ON. Illuminates when four -wheel drive high is engaged. If the light continues to flash have the system serviced. Door ajar Illuminates when the ignition is in the ON or ST ART position and any door is open.
Safety belt warning chime Chimes to remind you to fasten your safety belts. For information on the safety belt warning chime, refer to the Seating and safety restraints chapter . Supplemental restraint system (SRS) warning chime For information on the SRS warning chime, refer to the Seating and safety restraints chapter .
Speedometer Indicates the current vehicle speed. Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating.
Odometer Registers the total kilometers (miles) of the vehicle. T rip odometer Registers the kilometers (miles) of individual journeys. T o reset, depress the control. T achometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine.
Battery voltage gauge This gauge shows the battery voltage when the ignition is in the ON position. If the pointer moves and stays outside the normal operating range (as indicated), have the vehicle’ s electrical system checked as soon as possible. Engine oil pressure gauge This shows the engine oil pressure in the system.
MESSAGE CENTER (IF EQUIPPED) W ith the ignition in the ON position, the message center displays important vehicle information through a constant monitor of vehicle systems. Y ou may select display features on the message center for a display of status preceded by a brief indicator chime.
For maximum accuracy of this display feature, the ignition should be in the OFF position during fueling. The display FUEL LEVEL ERROR indicates a problem with the fuel indication system. See your dealer or qualified service technician for system maintenance.
System check Press the system check control to display the status of the following systems: • engine oil life left • engine oil level • voltage level • engine coolant temperature • washer fluid level • fuel level The engine oil life left has two phases.
Oil change reset Press the OIL CHANGE RESET control to reset the oil life feature to 100% (or your personalized oil reset percentage) (at optimal driving conditions, 100% oil life is equivalent to a maximum of 12 000 kilometers [7 500 miles]). After you have the oil changed, you must press and hold the OIL CHANGE RESET control for five seconds.
HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. Foglamp control (if equipped) T urn on the low-beam headlamps and press the foglamp control to activate the foglamps.
Flash to pass Pull toward you to activate and release to deactivate. P ANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlamp and parklamp operation. • Rotate up to brighten. • Rotate down to dim. • Rotate to full down position to turn off.
T emperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle.
• (Panel and floor)-Distributes outside air through the instrument panel registers and the floor ducts. Heating and air conditioning capabilities are provided in this mode.
• Remove any snow , ice or leaves from the air intake area (at the bottom of the windshield under the hood). • If your vehicle has been parked with the windows closed during hot weather , the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open.
Turning the EA TC off Press OFF . Automatic operation Press AUTOMA TIC and select the desired temperature. The selected temperature and the word AUTO will appear in the display window . The EA TC system will either heat or cool to achieve the selected temperature.
T o control the temperature, select any temperature between 18°C (65°F) and 29°C (85°F) by pressing the blue (cooler) or red (warmer) buttons. For continuous maximum cooling, push the blue button until 16°C (60°F) is shown in the display window .
• Rotate the thumbwheel up for higher fan speed or down for lower fan speed. • Press the steering wheel fan speed control up for higher fan speed or down for lower fan speed. The display will show to indicate manual fan operation. T o return to automatic fan operation, press AUTOMA TIC.
• PNL • FLR-Distributes outside air through the instrument panel registers and the floor ducts. Heating and air conditioning capabilities are provided in this mode.
The EA TC display window will indicate REAR F AN OFF . The rear console fan will remain off until REAR F AN OFF is pressed again. Operating tips • In humid weather , select DEF before driving. This will prevent your windshield from fogging. After a few minutes, select any desired position.
Rear console climate controls (if equipped) Depending on the equipment package of your vehicle, the rear console may be equipped with rear console audio/climate controls. The instrument panel climate controls must be on in order for the rear console climate controls to work.
Select for air to flow through these vents: REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice and fog. • The small LED will illuminate when the rear defroster is activated.
4WD CONTROL (IF EQUIPPED) This control operates the 4WD. Refer to the Driving chapter for more information. REVERSE SENSING SYSTEM (IF EQUIPPED) The reverse sensing system (RSS) sounds a tone to warn the driver of obstacles near the rear bumper when the reverse gear is selected.
The reverse sensing system detects obstacles within approximately 1.8 meters (5.9 ft.) of the rear bumper with a decreased coverage area at the outer corners of the bumper , (refer to the figures for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases.
USING YOUR AUDIO SYSTEM AM/FM stereo cassette V olume/power control Press the control to turn the audio system on or off. T urn the control to raise or lower volume.
If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio and tape modes.
Seek function in radio mode • Press to find the next listenable station down the frequency band. • Press to find the next listenable station up the frequency band. Scan function The scan function works in radio mode. Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band.
Bass adjust The bass adjust control allows you to increase or decrease the audio system’ s bass output. Treble adjust The treble adjust control allows you to increase or decrease the audio system’ s treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers.
T ape select • T o enter tape mode while in radio mode, press the T APE AMS control. Automatic Music Search The Automatic Music Search feature allows you to quickly locate the beginning of the tape selection being played or to skip to the next selection.
T ape direction select Press SIDE and 1–2 at the same time to play the alternate side of a tape. Eject function Press the control to stop and eject a tape. Dolby T noise reduction Dolby t noise reduction operates only in tape mode. Dolby t reduces the amount of hiss and static during tape playback.
• to decrease hours and • to increase hours. T o set the minute, press and hold the CLK control and press: • to decrease minutes and • to increase minutes.
AM/FM Stereo / Single CD Radio V olume/power control Press the control to turn the audio system on or off. T urn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
AM/FM select The AM/FM select control works in radio and CD modes. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in CD mode Press this control to stop CD play and begin radio play .
• Press to find the next listenable station up the frequency band. Seek function in CD mode • Press to listen to the next selection. • Press to listen to the previous selection.
Bass adjust The bass adjust control allows you to increase or decrease the audio system’ s bass output. Treble adjust The treble adjust control allows you to increase or decrease the audio system’ s treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers.
Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. CD select • T o begin CD play (if CD[s] are loaded), press the CD control. The first track of the disc will begin playing. After that, CD play will begin where it stopped last.
• to decrease hours and • to increase hours. T o set the minute, press and hold the CLK control and press: • to decrease minutes and • to increase minutes.
Premium AM/FM Stereo/Cassette/Single CD/Premium Sound V olume/power control Press the control to turn the audio system on or off. Audio power can also be turned on by pressing the AM/FM select control or the tape/CD select control. Audio power is turned off by using the volume/power control.
If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio, tape and CD modes.
Tune adjust for CD changer (if equipped) • Press to select the previous disc in the CD changer . (Play will begin on the first track of the disc unless the CD changer is in shuffle mode. Refer to Shuffle feature for more information. Hold the control to continue reversing through the remaining discs.
Seek function for CD or CD changer (if equipped) • Press to seek to the previous track of the current disc. If a selection has been playing for three seconds or more and you press , the CD changer will replay that selection from the beginning. • Press to seek forward to the next track of the current disc.
Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to T une adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected.
These stations are temporarily stored in the memory preset controls (until deactivated) and are accessed in the same manner of your original presets. T o deactivate autoset and return to your audio system’ s manually set memory stations, press the AUTO control again.
Press the BAL control then press: • to shift sound to the left and • to shift sound to the right. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the F ADE control then press: • to shift the sound to the front and • to shift the sound to the rear .
Rewind The rewind control works in tape and CD modes. • In tape mode, radio play will continue until rewind is stopped (with the T APE control) or the beginning of the tape is reached. • In CD mode, pressing the REW control rewinds the CD within the current track.
Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. Compression adjust Compression adjust brings soft and loud CD passages together for a more consistent listening level.
T o set the minute, press and hold the CLK control and press TUNE: • to decrease minutes and • to increase minutes. If your vehicle has a separate clock module, (other than the digital radio display), the CLK button will not function in the above manner .
Mute mode Press the control to mute the playing media. Press the control again to return to the playing media. Rear seat controls (if equipped) The Personal Audio System, a feature of the optional Pre.
T o activate the Personal Audio System, press the speaker/headphone control. Press the MODE control to change audio sources (for headphone mode only). Use the SEEK, VOLUME and MEMORY controls to make adjustments to the playing media. Adjusting the volume Press the + control to increase volume.
Turning the speakers on and of f Press to turn all speakers on or off. Using headphones Plug a 3.5 mm headphone (not included) into the jack. Press the speaker on/off control to operate the headphones. The rear speakers will cut out once the speaker on/off control is pressed.
Memory preset control Push the MEMORY control successively to allow rear seat passengers to scroll through the 6 memory presets in AM, FM1 or FM2. Push the MEMORY control in CD changer mode (if equipped) to advance to the next disc. Seek function • In radio mode, press to find the next listenable station down the frequency band.
MACH T Audio System with AM/FM Stereo/Cassette/Single CD Y our audio system is equipped with selective lighting, a unique lighting strategy . This lighting feature is operable when the headlamps are illuminated. During the operation of any selected mode, lighting for the individual function controls will either illuminate or turn off.
T urn control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly . • Press to move to the next frequency up the band (whether or not a listenable station is located there).
Seek function in tape mode • Press to listen to the previous selection on the tape. • Press to listen to the next selection on the tape. Seek function for CD changer (if equipped) • Press to seek to the previous track of the current disc.
Radio station memory preset The radio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and twelve FM stations (six in FM1 and six in FM2). Setting memory preset stations 1. Select the frequency band with the AM/FM select control.
Bass adjust The bass adjust control allows you to increase or decrease the audio system’ s bass output. Press the BASS control then press: • to decrease bass output and • to increase bass output. Treble adjust The treble adjust control allows you to increase or decrease the audio system’ s treble output.
• to shift sound to the left and • to shift sound to the right. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the F ADE control then press: • to shift sound to the front and • to shift sound to the rear .
Rewind The rewind control works in tape and CD modes. • In tape mode, radio play will continue until rewind is stopped (with the T APE control) or the beginning of the tape is reached. • In CD mode, pressing the REW control for less than three seconds results in slow rewind.
Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. Compression adjust Compression adjust brings soft and loud CD passages together for a more consistent listening level.
T o set the minute, press the clock/RDS control until SELECT MIN is displayed and press: • to decrease minutes and • to increase minutes. Radio Data System (RDS) feature This feature allows your audio system to receive text information from RDS-equipped FM radio stations.
RDS traffic announcement • Press the RDS control until TRAFFIC is displayed. • Use the SELECT control to select ON or OFF . W ith the feature ON, use the SEEK or SCAN control to find a radio station broadcasting a traffic report (if it is broadcasting RDS data).
• Classic • Country • Info • Jazz/R&B • Religious • Rock • Soft • To p 4 0 RDS show • W ith the RDS menu enabled, press the RDS control until SHOW is displayed.
Rear seat controls (if equipped) The Personal Audio System, a feature of the optional Premium AM/FM Stereo/Cassette/Single CD/Premium Sound and the MACH t Audio System with AM/FM Stereo/Cassette/Single CD, allows front and middle seat passengers to listen to different media sources (radio, cassette or CD) simultaneously .
Adjusting the volume Press the + control to increase volume. Press the - control to decrease volume. From the rear seat controls, volume control can be set no higher than the current radio setting unless the speakers are turned off. Refer to T urning speakers on and off.
The rear speakers will cut out once the speaker on/off control is pressed. The front speaker will remain playing for the front passengers. Press the control again to deactivate the headphones. Mode select Push the MODE control to toggle between AM, FM1, FM2, tape, CD or CD changer (if equipped).
• In CD mode (if equipped), use the SEEK function to access the next or previous selection. CD changer (if equipped) The CD changer is located in one of the following locations: • in the trunk • in the center console • under the driver’ s seat 1.
If you pull too hard on the disc holder , the disc holder may come completely out of the magazine. If this happens, reinsert the disc holder back into the magazine while pressing on the lever (A). 5. Line up the CD with the groove of the disc holder .
The CD magazine may be inserted or ejected with the radio power off. ONL Y use the magazine supplied with the CD changer , other types will damage the unit. Keep the CD changer door closed. Coins and foreign objects will damage the CD player and void your audio system warranty .
Cleaning cassette player (if equipped) Clean the tape player head with a cassette cleaning cartridge after ten to twelve hours of play in order to maintain the best sound and operation. Cassette and cassette player care • Use only cassettes that are 90 minutes long or less.
• Station overload. W eak signals are sometimes captured by stronger signals when you pass a broadcast tower . A stronger signal may temporarily overtake a weaker signal and play while the weak station frequency is displayed.
SPEED CONTROL (IF EQUIPPED) T o turn speed control on • Press ON. V ehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not use the speed control in heavy traffic or on roads that are winding, slippery , or unpaved.
T o set a speed • Press SET/SET ACC/SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed.
Y ou can accelerate with the accelerator pedal at any time during speed control usage. Releasing the accelerator pedal will return your vehicle to the previously programmed set speed. T o set a lower set speed • Press and hold CST/COAST . Release the control when the desired speed is reached or • Press and release CST/COAST .
T o disengage speed control • Depress the brake pedal or • Depress the clutch pedal (if equipped) Disengaging the speed control will not erase the previously programmed set speed.
T o return to a previously set speed • Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph). Indicator light This light comes on when either the SET ACC/SET ACCEL or RES/RSM/RESUME controls are pressed.
TIL T STEERING WHEEL (IF EQUIPPED) Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control to lock the steering wheel in position. Never adjust the steering wheel when the vehicle is moving.
Push the control on the end of the stalk to activate washer . Push and hold for a longer wash cycle. The washer will automatically shut off after ten seconds of continuous use.
Radio control features • Press BAND/MODE to select AM, FM1, FM2, T APE or CD (if equipped). In Radio mode: • Press MEM/NEXT to select a preset station from memory . In T ape mode: • Press MEM/NEXT to listen to the next selection on the tape. In CD mode: • Press MEM/NEXT to listen to the next track on the disc.
Storage compartment (if equipped) Press the OPEN control to open the storage compartment. The door will open slightly and can be moved to full open. Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: • Remove the storage clip from the door .
• Press the GARAGE control to activate the transmitter . Moon roof (if equipped) Y ou can move the moon roof back to open the glass panel or tilt up to ventilate the vehicle. T o open the moon roof: The moon roof is equipped with an automatic, one-touch, express opening feature.
Electronic compass/temperature display (if equipped) Outside air temperature The outside temperature display is contained in the overhead console. The temperature display can be turned off and on by pressing the MODE control on the overhead console. The temperature can be displayed in Centigrade or Fahrenheit by pressing the MODE control.
Compass zone adjustment 1. Determine which magnetic zone you are in by referring to the zone map. 2. Press and hold the MODE control until V AR appears in the display , then release. The display should show the current zone number . 3. Press the MODE control until the desired zone number appears.
Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines: • Press and hold the MODE control until CAL appears in the display (approximately eight seconds) and release.
Programming 1. Prepare for programming the HomeLink t Universal T ransceiver by erasing the three factory default codes by holding down the two outside buttons until the red light begins to flash after 20 seconds.
Operating the HomeLink T Universal T ransceiver Once programmed, the HomeLink t Universal T ransceiver can be used in place of hand-held transmitters. T o operate, simply press and release the appropriate HomeLink t button (the red light will illuminate, indicating the signal is being transmitted).
The 2nd or 3rd press from step 3 will activate the door . The HomeLink t Universal T ransceiver has now been trained to the receiver . The remaining two buttons may now be programmed if this has not previously been done. Erasing HomeLink T buttons Individual buttons cannot be erased, however , to erase the three programmed buttons: 1.
T o record a message: 1. Press and release the REC button one time to start recording. (An audible tone will sound, confirming the onset of recording). 2. Press and release the REC button a second time to end recording. (An audible tone will sound again, confirming the end of recording and the red indicator light will turn off.
If the DEL button is inadvertently pressed or the time allotted (5 seconds) has passed, the indicator light will flash amber and an “error” tone will sound. AUTOLAMP DELA Y SYSTEM (IF EQUIPPED) The autolamp sets the headlamps to turn on and off automatically .
Automatic dimming rear view mirror The autolamp/automatic dimming mirror is equipped with an automatic dimming feature. This feature will change from the normal state to the non-glare “active” state when bright lights (glare) reach the mirror .
One touch down • Press AUTO completely down and release quickly . The driver’ s window will open fully . Depress again to stop window operation. Window lock The window lock feature allows only the driver to operate the power windows. T o lock out all the window controls except for the driver’ s press the left side of the control.
CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door .
Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place.
Auxiliary power point The power point is an additional power source for electrical accessories. Rear console features The rear console incorporates the following features: • air vents • audio syst.
POSITIVE RETENTION FLOOR MA T T o install floor mats: 1. Move the driver’ s seat to the most rearward position 2. Position the driver’ s side floor mat with the rear of the mat against left (outboard) front edge of seat track mounting bracket. 3. Use a screwdriver to screw locator post into vehicle carpeting.
Make sure that the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. If you must drive with the liftgate door or window open, keep the vents open so outside air comes into the vehicle.
2. W rap the vinyl around the roller tube twice. T uck the edges of the vinyl inside the end cap with each wrap. 3. Fold the edges of the vinyl towards the center , making sure that the edges clear the end cap slots. Use tape or a rubber band to hold the vinyl to the left side of the tube.
Unlocking the doors Press this control to unlock the driver’ s door . The interior lamps will illuminate. Press the control a second time within five seconds to unlock all doors. Locking the doors Press this control to lock all doors. T o confirm all doors are closed and locked, press the control a second time within five seconds.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’ s authority to operate the equipment. Memory seat feature (if equipped) The remote entry system can also control the memory seat feature.
The memory feature will continue to work from the door control even when deactivated at the remote entry module. Replacing the battery The transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. T ypical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle.
Replacing lost transmitters T ake all your vehicle’ s transmitters to your dealer if service is required. If you purchase additional transmitters (up to four may be programmed), perform the followin.
The autolock feature repeats when: • any door is opened and then closed • the brake pedal is released Deactivating autolock Before following the activation or deactivation procedures, make sure that the ignition is OFF and all vehicle doors and liftgate window are closed.
If autolock/relock has been changed, the horn will chirp to confirm procedure is complete. Keyless entry system (if equipped) W ith the keyless entry keypad, you can: • lock or unlock the vehicle doors without using the key • activate/deactivate the autolock feature See also Remote entry system in this chapter for more information.
If you wish to erase your personal code, use the following instructions: Erasing personal code 1. Enter the factory-set code. 2. Press 1/2 within five seconds of step 1. 3. Press the 7/8 and 9/0 controls at the same time within five seconds of step two.
SECURILOCK Y PASSIVE ANTI-THEFT SYSTEM The SecuriLock y passive anti-theft system provides an advanced level of vehicle theft protection. Y our vehicle’ s engine can only be started with the two special SecuriLock y electronically coded keys provided with your vehicle.
Programming spare SecuriLock Y keys Spare SecuriLock y keys can be purchased from your dealership and programmed to your SecuriLock y passive anti-theft system (up to a total of 8 keys). Y our dealership can program your new SecuriLock y key(s) to your vehicle or you can do it yourself using the following simple procedure.
5. W ithin 10 seconds of turning the ignition to OFF , insert the unprogrammed SecuriLock y key (new key) into the ignition and turn the ignition from OFF to RUN (maintain ignition in RUN for at least one second). This step will program your new SecuriLock y key .
SEA TING Adjustable head restraints Y our vehicle’ s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision.
Adjusting the front power seat (if equipped) Never adjust the driver’ s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Memory seats (if equipped) This system allows automatic positioning of the driver seat to three programmable positions. The memory seat control is located on the driver door . • T o program position one, move the driver seat to the desired position using the seat controls.
head motion in the event of a rear collision. T o properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible. Refer to the following to raise and lower the head restraints.
T o return the seat to the upright position: • Press downward on the upper corner of the seatback and hold. • Pull the release handle upward to unlatch the seat. • Rotate the seatback upward until the seatback latches in the upright position. The seatback will click when it is locked into position.
All occupants of the vehicle, including the driver , should always properly wear their safety belts, even when an air bag SRS is provided. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
2. T o unfasten, push the release button and remove the tongue from the buckle. The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts.
How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
• This seat belt system has a retractor assembly that is designed to pay out webbing in a controlled manner . This feature is designed to help reduce the belt force acting on the occupant’ s chest.
Safety belt extension assembly If the safety belt assembly is too short, even when fully extended, 20 cm (8 inches) can be added to the safety belt assembly by adding a safety belt extension assembly (part number 611C22). Safety belt extension assemblies can be obtained from your dealer at no cost.
Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged. Inspect the safety belts to make sure there are no nicks, wears or cuts, replacing if necessary .
Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries.
Do not attempt to service, repair , or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer . Children and air bags For additional important safety information, read all information on safety restraints in this guide.
The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.
• and the electrical wiring which connects the components. The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system warning (including the impact sensors), the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors.
All occupants of the vehicle including the driver should always wear their safety belts even when an air bag SRS is provided. How does the side air bag system work? The side air bag system consists of.
The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system. Rather , it means the forces were not of the type sufficient to cause activation.
Disposal of air bags and air bag equipped vehicles For disposal of air bags or air bag equipped vehicles, see your local dealership or qualified technician. Air bags MUST BE disposed of by qualified personnel. SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safety restraints for children.
If the shoulder belt portion of a combination lap and shoulder belt can be positioned so it does not cross or rest in front of the child’ s face or neck, the child should wear the lap and shoulder belt. Moving the child closer to the center of the vehicle may help provide a good shoulder belt fit.
When installing a child safety seat: • Review and follow the information presented in the Air Bag Supplemental Restraint System section in this chapter . • Use the correct safety belt buckle for that seating position. • Insert the belt tongue into the proper buckle until you hear a snap and feel it latch.
Installing child safety seats in combination lap and shoulder belt seating positions 1. Position the child safety seat in a seat with a combination lap and shoulder belt. An air bag can kill or injure a child in a child seat. If you must use a forward-facing child seat in the front seat, move seat all the way back.
3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat.
The provision (attaching hole) is provided in the rear edge of the front passenger seat cushion frame. The anchorbracket must be installed using the instructions provided with the kit. T ether anchorage hardware kits (part number 613D74) including instructions, may be obtained at no charge from any Ford or Lincoln-Mercury dealer .
PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
If starting a vehicle with an automatic transmission: • Make sure the parking brake is set. • Make sure the gearshift is in P (Park). If starting a vehicle with a manual transmission: • Make sure the parking brake is set. • Push the clutch pedal to the floor .
Make sure the corresponding lights illuminate briefly . If a light fails to illuminate, have the vehicle serviced. • If the driver’ s safety belt is fastened, the light will not illuminate. ST ARTING THE ENGINE 1. T urn the key to 5 (ST ART) without pressing the accelerator pedal and release as soon as the engine starts.
4. After idling for a few seconds, apply the brake and release the parking brake. Using the engine block heater (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater -defroster system to respond quickly .
Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch). Adjust the heating or air conditioning (if equipped) to bring in fresh air . Improve vehicle ventilation by keeping all air inlet vents clear of snow , leaves and other debris.
BRAKES Y our service brakes are self-adjusting. Refer to the maintenance guide and or service guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’ s brake system.
ABS warning lamp The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned on and the engine is off. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced.
The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (manual transmission).
• underinflated tire(s) on any wheel(s) • high crown in center of road • high crosswinds • wheels out of alignment • loose or worn components in steering linkage AIR SUSPENSION SYSTEM (IF EQ.
T RANSMISSION OPERATION Automatic transmission operation Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift from being moved from P (Park) unless the brake pedal is depressed. If you cannot move the gearshift out of P (Park) with the brake pedal depressed: 1.
Driving with a 4–speed automatic transmission (if equipped) Understanding gearshift positions Pull the gearshift lever towards you and downward to move the automatic gearshift. Hold the brake pedal down while you move the gearshift lever from P (Park) to another position.
(Overdrive) The normal driving position for the best fuel economy . T ransmission operates in gears one through four . (Overdrive) can be deactivated by pressing the transmission control switch on the end of the gearshift lever . The transmission control indicator light (TCIL) will illuminate on the instrument cluster .
1 (First) Use 1 (Low) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to (Overdrive). Selecting 1 (Low) at higher speeds causes the transmission to shift to a lower gear , and will shift to 1 (Low) after vehicle decelerates to the proper speed.
N (Neutral) W ith the gearshift in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this gear . (Overdrive) The normal driving position for the best fuel economy . T ransmission operates in gears one through five.
2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. T ransmission operates in third gear . 1 (First) Use 1 (First) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to (Overdrive).
5. Release the clutch slowly while pressing gradually down on the accelerator pedal. • Do not drive with your foot resting on the clutch pedal. Do not use the clutch to hold your vehicle at a standstill while waiting on a hill. These actions may reduce clutch life.
Recommended shift speeds Upshifts when accelerating (for best fuel economy) Shift from: T ransfer case position (if equipped) AUTO or HIGH LOW 1 - 2 14 km/h (10 mph) 5 km/h (4 mph) 2 - 3 32 km/h (22 m.
FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED) If equipped with the Electronic Shift 4WD System, and the instrument panel control is moved to 4WD Low while the vehicle is moving, the system will not engage and no damage will occur to the 4WD system.
• The 4WD HIGH mode provides four -wheel drive with full power to both axles. It is only intended for severe winter or off-road conditions, such as deep snow and ice (where no dry or wet pavement remains uncovered), and shallow sand.
Using the Control-T rac system Shifting between 4WD AUTO and 4WD HIGH When you move the control to 4WD HIGH, the indicator light will illuminate in the instrument cluster . When you move the control to 4WD AUTO, the indicator light will turn off. Either shift can be done at a stop or while driving at any speed.
Driving off-road with 4WD Y our vehicle is specially equipped for driving on sand, snow , mud and rough terrain and has operating characteristics that are somewhat different from conventional vehicles, both on and off the road. Maintain steering wheel control at all times, especially in rough terrain.
Once through water , always try the brakes. W et brakes do not stop the vehicle as effectively as dry brakes. Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal. After driving through mud, clean off residue stuck to rotating driveshafts and tires.
Driving on snow and ice A 4WD vehicle has advantages over 2WD vehicles in snow and ice but can skid like any other vehicle. A void sudden applications of power and quick changes of direction on snow and ice. Apply the accelerator slowly and steadily when starting from a full stop.
Y ou should either know the terrain or examine maps of the area before driving. Map out your route before driving in the area. For more information on driving off-road, read the “Four Wheeling” supplement in your owner’ s portfolio.
If the rear axle is submerged in water , the rear axle lubricant should be checked and changed, if necessary . The rear axle is filled with a synthetic lubricant and does not normally require a lubricant change for the life of the vehicle. Rear axle lubricant quantities should not need to be checked unless a leak is suspected.
T RACTION-LOK AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly when one wheel is on a poor traction surface. Under normal conditions, the T raction-Lok axle functions like a standard rear axle.
• Maximum T railer W eight Rating : Maximum weight of a trailer the vehicle is permitted to tow . The maximum trailer weight rating is determined by subtracting the vehicle curb weight for each engine/transmission combination, any required option weight for trailer towing and the weight of the driver from the GCWR for the towing vehicle.
Calculating the load your vehicle can carry/tow 1. Use the appropriate maximum gross combined weight rating (GCWR) chart to find the maximum GCWR for your type engine and rear axle ratio. 2. W eigh your vehicle as you customarily operate the vehicle without cargo.
T RAILER TOWING T railer towing with your vehicle may require the use of a trailer tow option package. T railer towing puts additional loads on your vehicle’ s engine, transmission, axle, brakes, tires, and suspension. For your safety and to maximize vehicle performance, be sure to use the proper equipment while towing.
T railer towing table (4x2 manual transmission) GCWR (Gross Combined W eight Rating)/T railer weights Engine Rear axle ratio Maximum GCWR-kg (lbs.) T railer weight range-kg (lbs.) (0-Maximum) Maximum frontal area of trailer -m 2 (ft 2 ) 2-door 4.0L OHV 3.
T railer towing table (4x4 manual transmission) GCWR (Gross Combined W eight Rating)/T railer weights Engine Rear axle ratio Maximum GCWR-kg (lbs.) T railer weight range-kg (lbs.) (0-Maximum) Maximum frontal area of trailer -m 2 (ft 2 ) 2-door 4.0L OHV 3.
T railer towing table (4x2 automatic transmission) GCWR (Gross Combined W eight Rating)/T railer weights Engine Rear axle ratio Maximum GCWR-kg (lbs.) T railer W eight Range-kg (lbs.) 0-Maximum Maximum frontal area of trailer -m 2 (ft 2 ) 2-door 4.0L SOHC 3.
T railer towing table (4x4 and A WD with automatic transmission) GCWR (Gross Combined W eight Rating)/T railer W eights Engine Rear axle ratio Maximum GCWR-kg (lbs.) T railer W eight Range-kg (lbs.) 0-Maximum Maximum frontal area of trailer -m 2 (ft 2 ) 2-door 4.
T railer towing table (4x4 and A WD with automatic transmission) Notes: For high altitude operation, reduce GCW by 2% per 300 meters (1 000 ft) elevation. For definition of terms and instructions on calculating your vehicle’ s load, refer to V ehicle loading in this chapter .
Safety chains Always connect the trailer’ s safety chains to the vehicle. T o connect the trailer’ s safety chains, cross the chains under the trailer tongue and allow slack for turning corners. If you use a rental trailer , follow the instructions that the rental agency gives to you.
Driving while you tow Do not drive faster than 88 km/h (55 mph) when towing a trailer . Speed control may shut off if you are towing on long, steep grades. When towing a trailer: • Use a lower gear when towing up or down steep hills. This will eliminate excessive downshifting and upshifting for optimum fuel economy and transmission cooling.
Launching or retrieving a boat When backing down a ramp during boat launching or retrieval, • Do not allow the static water level to rise above the bottom edge of the rear bumper and • Do not allow waves to break higher than 15 cm (six inches) above the bottom edge of the rear bumper .
LUGGAGE RACK Maximum load is 90 kg (200 lbs), evenly distributed. If it is not possible to distribute the load, position it as far rearward as possible. Adjustable tie down loops must be used to secure the load. T o adjust cross-bar position: 1. Loosen the thumbwheel at both ends of the cross-bar (both cross-bars are adjustable).
HAZARD FLASHER Use only in an emergency to warn traffic of vehicle breakdown, approaching danger , etc. The hazard flashers can be operated when the ignition is off. • The hazard lights control is located on top of the steering column. • Depress hazard lights control to activate all hazard flashers simultaneously .
The fuel pump shut-off switch is located in the passenger’ s foot well, behind the kick panel. FUSES AND RELA YS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse.
Standard fuse amperage rating and color COLOR Fuse Rating Mini Fuses Standard Fuses Maxi Fuses Cartridge Maxi Fuses Fuse Link Cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A T an T an — — — 7.
Passenger compartment fuse panel The fuse panel is located on the left hand side of the instrument panel facing the driver’ s side door . Pull the panel cover outward to access the fuses. T o remove a fuse use the fuse puller tool provided on the fuse panel cover .
The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Description 1 7.5A Power Mirror Switch, Power Antenna 2 7.5A Blower Motor Relay , Air Bag Diagnostic Monitor 3 7.5A Left Stop/T urn T railer T ow Connector 4 10A Left Headlamp 5 10A Data Link Connector (DLC) 6 7.
Fuse/Relay Location Fuse Amp Rating Description 20 7.5A RAP Module, Generic Electronic Module (GEM), Radio 21 15A Flasher (Hazard) 22 20A Auxiliary Power Socket 23 — Not Used 24 7.5A Clutch Pedal Position (CPP) Switch, Starter Interrupt Relay , Anti-Theft 25 7.
Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’ s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses.
The high-current fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Description 1 60A** I/P Fuse Panel 2 40A** Blower Motor Relay 3 50A** 4 Wheel Anti-Lock Brake System (4W ABS) Module 4 .
Fuse/Relay Location Fuse Amp Rating Description 3 30A* Heated Backlight 4 15A* Fog Lamps and Daytime Running Lamps 5 — Not Used 6 10A* Powertrain Control Module 7 30A* 4 Wheel Anti-Lock System (4W A.
CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily . Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Spare tire information Y our vehicle is equipped with a 15” spare tire that must be used for emergencies only .
Removing the spare tire 1. Insert the jack handle into the rear bumper opening. The handle will stop moving and forward resistance to turning will be felt when properly engaged. 2. T urn the handle counterclockwise until tire is lowered to the ground, the tire can be slid rearward and the cable is slightly slack.
Refer to the instruction sheet for detailed tire change instructions. 1. Park on a level surface, activate hazard flashers and set the parking brake. 2. Place gearshift lever in P (Park) or in the reverse gear (manual transmission) and turn engine OFF .
6. T urn OFF the air suspension switch (if equipped). Refer to Air suspension system in the Driving chapter . 7. Position the jack according to the following guides and turn the jack handle clockwise until the tire is a maximum of 25 mm (1 inch) off the ground.
T o lessen the risk of personal injury , do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. • Never use the front or rear differential as a jacking point.
JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. Y ou could damage the catalytic converter . Batteries contain sulfuric acid which can burn skin, eyes, and clothing, if contacted.
Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery . Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery .
3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor .
• 4.0L SOHC 5. Be sure that the cables are clear of fan blades, belts and other moving parts of both engines. Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle.
Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface.
2. Remove the jumper cable on the negative (-) connection of the booster vehicle’ s battery . 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery .
4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
If equipped with air suspension, the air suspension control must be turned to the OFF position. The Ford approved towing procedure is flatbed or wheel lift with dollies. On 4x2 vehicles, it is acceptable to tow the vehicle with the front wheels on the ground (without dollies) and the rear wheels off the ground.
SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide a Scheduled Maintenance Guide which makes tracking routine service easy . If your vehicle requires professional service, your dealership can provide necessary parts and service.
• Manual transmission: 1. Set the parking brake. 2. Depress the clutch and place the gearshift in 1 (First). 3. T urn off the engine and remove the key . 4. Block the wheels to prevent the vehicle from moving unexpectedly . Working with the engine on • Automatic transmission: 1.
2. Go to the front of the vehicle and release the auxiliary latch that is located in the center between the hood and the grill. 3. Lift the hood until the lift cylinders hold it open.
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.0L OHV V6 engine 1. W indshield washer fluid reservoir 2. Engine oil filler cap 3. T ransmission fluid dipstick (automatic transmission) 4. Engine oil dipstick 5. Power steering fluid reservoir 6. Brake fluid reservoir 7.
4.0L SOHC V6 engine 1. W indshield washer fluid reservoir 2. Automatic transmission fluid dipstick 3. Engine oil filler cap 4. Engine oil dipstick 5. Brake fluid reservoir 6.
5.0L V8 engine 1. Engine coolant reservoir 2. W indshield washer fluid reservoir 3. Engine oil filler cap 4. Automatic transmission fluid dipstick 5. Brake fluid reservoir 6.
4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick). • 4.0L V6 engines • 5.0L V8 engine 6. W ipe the indicator clean. Insert the indicator fully , then remove it again. • If the oil level is between the ADD and FULL marks (4.
• If the oil level is below the ADD mark (4.0L engines) or MIN mark (5.0L engine), add enough oil to raise the level within the ADD-FULL range (4.0L engines) or MIN-MAX range (5.0L engine). • Oil levels above the letter F in FULL (4.0L engines) or the MAX mark (5.
Do not use supplemental engine oil additives, oil treatments or engine treatments. They are unnecessary and could, under certain conditions, lead to engine damage which is not covered by your warranty . Change your engine oil and filter according to the appropriate schedule listed in the Scheduled Maintenance Guide.
Brake fluid is toxic. If you use a brake fluid that is not DOT 3, you will cause permanent damage to your brakes. Do not let the reservoir for the master cylinder run dry . This may cause the brakes to fail. CLUTCH FLUID (IF EQUIPPED) Check the clutch fluid level.
WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. If the level is low , add enough fluid to fill the reservoir . In very cold weather , do not fill the reservoir all the way .
If the engine coolant has not been checked at the recommended interval, the engine coolant reservoir may become empty . If this occurs, add engine coolant to the reservoir . For more information on engine coolant maintenance, refer to Adding engine coolant in this chapter .
If you must remove the coolant reservoir cap, follow these steps to avoid personal injury: 1. Before you remove the cap, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the cap. Slowly turn cap counterclockwise until pressure begins to release.
For vehicles with orange coolant, no recycling process has been approved at this time and use of such coolant may harm engine and cooling system components. Always dispose of used automotive fluids in a responsible manner . Follow your community’ s regulations and standards for recycling and disposing of automotive fluids.
• 4.0L OHV V6 engine • 4.0L SOHC V6 engine • 5.0L V8 engine D O N O T O V E R F I L L P O W E R S T E E R I N G F L U I D Maintenance and care 214.
1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C). 2. While the engine idles, turn the steering wheel left and right several times.
5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. 6. Install the dipstick making sure it is fully seated in the filler tube. 7. Remove the dipstick and inspect the fluid level. The fluid should be in the designated areas for normal and room temperature.
Use of a non-approved automatic transmission fluid may cause internal transmission component damage. If necessary , add fluid in 250 mL (1/2 pint) increments through the filler tube until the level is correct. If an overfill occurs, excess fluid should be removed by a qualified technician.
3. Fluid level should be at bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely . Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter .
3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter . DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Y our vehicle may be equipped with universal joints that require lubrication.
If the electrolyte level in the battery is low , you can add plain tap water to the battery , as long as you do not use hard water (water with a high mineral or alkali content). If possible, however , try to only fill the battery cells with distilled water .
1. Set your parking brake. 2. Put the gearshift in P (Park) (automatic transmission) or the neutral position (manual transmission), turn off all accessories and start the engine. 3. Let the engine idle for at least one minute. 4. The relearning process will automatically complete as you drive the vehicle.
Changing the wiper blades T o replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. T urn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm.
T readwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100.
SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles).
• 16’’ Five tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial, bias-belted, or bias-type tires. Use only the tire sizes that are listed on the tire pressure decal.
Do not replace your tires with “high performance” tires or larger size tires. Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over .
Consult your dealer for information on other Ford approved methods of traction control. WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire.
• A void inhaling fuel vapors. Inhaling too much fuel vapor of any kind can lead to eye and respiratory tract irritation. In severe cases, excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury . • A void getting fuel liquid in your eyes.
Octane recommendations Y our vehicle is designed to use “Regular” unleaded gasoline with an (R+M)/2 octane rating of 87. W e do not recommend the use of gasolines labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas.
Running out of fuel A void running out fuel because this situation may have an adverse affect on powertrain components. If you have run out of fuel: • Y ou may need to crank the engine several times before the system starts to pump fuel from the tank to the engine.
If you do not use the proper fuel filler cap, the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision. Fuel Filter Y our vehicle is equipped with a fuel filter that is mounted on the underbody . For fuel filter replacement, see your dealer or a qualified service technician.
Filling the tank For consistent results: • Use the same filling rate setting (low — medium — high) each time the tank is filled. • Allow three automatic click-offs when filling. • Always use the recommended octane rating of a known quality gasoline, preferably a national brand.
Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy . • Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop.
Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed. • Carrying unnecessary weight may reduce fuel economy (approximately 2 km/h [1 mpg] is lost for every 180 kg [400 lb] of weight carried).
• Do not turn off the ignition while your vehicle is moving, especially at high speeds. • Have the items listed in your Scheduled Maintenance Guide performed according to the specified schedule.
Readiness for inspection/maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test of the on-board diagnostic (OBD-II) system. If your “Check Engine/Service Engine Soon” light is on, refer to the description in the W arning Lights and Chimes section of the Instrumentation chapter .
Replacing headlamp bulbs Handle a halogen headlamp bulb carefully and keep out of children’ s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.
T o install the new bulb: 1. W ith the flat side of the new bulb’ s plastic base facing upward, insert the glass end of the bulb into the lamp assembly . Y ou may need to turn the bulb left or right to align the grooves in the plastic base with the tabs in the lamp assembly .
Replacing tail lamp/backup lamp bulbs The tail lamp/backup lamp bulbs are located in the same portion of the tail lamp assembly , one just below the other . Follow the same steps to replace either bulb: 1. Open the liftgate to expose the lamp assemblies.
License plate lamp bulbs T o change the license plate bulbs: 1. Remove two screws and the license plate lamp assembly from the liftgate. 2. Pull the bulb out from lamp assembly and push in the new bulb. 3. Install the lamp assembly on liftgate with two screws.
AIMING THE HEADLAMPS The alignment of your headlamps should be checked by a qualified service technician if: • Oncoming motorists frequently signal you to deactivate your high beams, and your high beams are not activated. • The headlamps do not seem to provide enough light for clear night vision.
W axing your vehicle W ax when water stops beading on the surface. This could be every three or four months, depending on operating conditions. Use only carnauba or synthetic-based waxes. Use cleaning fluid or alcohol with a clean cloth to remove any bugs and tar before waxing vehicle.
• 5.0L • 4.0L SOHC Maintenance and care 243.
• 4.0L OHV • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning the wheels W ash with the same detergent as the body of your vehicle. Do not use acid-based or alcohol-based wheel cleaners, steel wool, fuel or strong detergents.
Cleaning the wiper blades and windshield If the wiper blades do not wipe properly , clean the wiper blade rubber element with undiluted windshield washer solution or a mild detergent. T o avoid damaging the blades, do not use fuel, kerosene, paint thinner or other solvents.
Cleaning the interior fabric Remove dust and loose dirt with a whisk broom or a vacuum cleaner . Remove fresh spots immediately . Do not use household or glass cleaners. These agents can stain and discolor the fabric. Use a mild soap and water solution if necessary .
MOTORCRAFT PART NUMBERS Component 4.0L OHV V6 engine 4.0L SOHC V6 engine 5.0L V8 engine Air filter F A-1658 F A-1658 F A-1658 Fuel filter FG-986B FG-986B FG-986B Battery BXT -65-650 BXT -65-650 BXT -6.
Fluid Ford Part Name Application Capacity T ransmission fluid Motorcraft MERCON t AT F 5-speed manual 2.6L (5.6 pints) 4R70W Automatic with 5.0L V8 engine 13.1L (13.9 quarts) 5R55E Automatic with 4.0L V6 engine (4x2) 9.5L (10.0 quarts) 5R55E Automatic with 4.
Fluid Ford Part Name Application Capacity Rear axle lubricant 2, Motorcraft SAE 80W90 Premium Rear Axle Lubricant Refer to footnote 3 2.9-3.1L (5.5-5.8 pints) Motorcraft SAE 75W140 High Performance Synthetic Rear Axle Lubricant Refer to footnote 4 W indshield washer fluid Ultra-Clear W indshield W asher Concentrate All 2.
LUBRICANT SPECIFICATIONS Item Ford Part Name or equivalent Ford Part Number Ford Specification Body hinges, latches, door striker plates and rotors, seat tracks, fuel filler door hinge and spring, hoo.
Item Ford Part Name or equivalent Ford Part Number Ford Specification Power steering fluid Motorcraft MERCON t AT F XT -2-QDX MERCON t Ford conventional and T raction-Lok rear axles 2, 3, 4 2, 3, 4 2,.
ENGINE DATA Engine 4.0L OHV V6 engine 4.0L SOHC V6 engine 5.0L V8 engine Cubic inches 245 245 302 Horsepower 160 @ 4200 rpm 210 @ 5250 rpm 215 @ 4200 rpm T orque 225 lb.-ft. @ 2750 rpm 240 lb.-ft. @ 3250 rpm 288 lbs.ft. @ 3300 rpm Recommended fuel 87 octane 87 octane 87 octane Firing order 1-4-2-5-3-6 1-4-2-5-3-6 1-3-7-2-6-5-4-8 Spark plug gap 1.
Dimensions 4-Door 4x2 XL Model mm (in.) 4-Door 4x4 XL T Model mm (in.) (1) Overall length 4 857 (191.2) 4 857 (191.2) (2) Overall width 1 783 (70.2) 1 783 (70.2) (3) Maximum height 1 719 (67.7) 1 793 (70.6)* (4) Wheelbase 2 835 (111.6) 2 835 (111.6) (5) Front track 1 486 58.
IDENTIFYING YOUR VEHICLE Safety compliance label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located.
V ehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel. Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block, transmission, frame and transfer case (if equipped).
REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company .
Air bag supplemental restraint system ........................................ 126 and child safety seats ............ 128 description .......................127,130 disposal .................................... 133 indicator light ..................130,132 passenger air bag .
Engine oil checking and adding .............. 207 dipstick .................................... 205 specifications ...................205,207 Exhaust fumes .......................... 143 Floor mats ................................. 103 Four -Wheel Drive vehicles .
speed control ............................84 turn signal indicator ................... 8 Locks childproof ................................ 100 Lumbar support, seats ...... 116,118 Manual transmission reverse ..................................... 156 Message center .
T ransmission ...................... 149,215 automatic operation ............... 149 fluid, checking and adding (automatic) ......................215,216 fluid, checking and adding (manual) ................................. 217 manual operation ......
261.
262.
Item Information Recommended fuel Unleaded fuel only - 87 octane Fuel tank capacity (2 door) 65.5L (17.3 gallons) Fuel tank capacity (4 door) 78.7L (20.8 gallons) Engine oil capacity (includes filter change) 4.7L (5.0 quarts). Use Motorcraft 5W30 Super Premium Motor Oil, Ford specification WSS-M2C153-G.
2 Ensure correct automatic transmission fluid is used for a specific application. Check the container to verify the fluid is MERCON t and/or MERCON t V approved. Some fluids have been approved as meeting both MERCON t and MERCON t V requirements and will be labeled as such.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Ford 1999 Explorer è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Ford 1999 Explorer - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Ford 1999 Explorer imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Ford 1999 Explorer ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Ford 1999 Explorer, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Ford 1999 Explorer.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Ford 1999 Explorer. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Ford 1999 Explorer insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
