Manuale d’uso / di manutenzione del prodotto H7182 del fabbricante Fisher-Price
Vai alla pagina of 16
1 Instructions Model Number: H7182 Please read these instructions befor e assembly and use of this product. Adult assembly is requir ed. Tool needed for assembly: Phillips Scr ewdriver (not included). Requires thr ee “ AA ” (LR6) alkaline batteries for toy operation (not included).
W ARNING This product contains small par ts in its unassemb led state. Adult assemb ly is required. Prevent serious injury or death fr om falls or sliding out: • The child should at all times wear a saf ety harness correctly fitted and adjusted. The tra y is not designed to hold the child in the chair .
Pa d Food Tr ay 2 Teether T oys Seat Back Frame Seat Bottom Frame Hinge Rod 2 Seat Bottom Tubes 2 Screw Retainer s Screw Retainer Screw Retainer Base Tr ay Footrest Front Base Back Base #10 x 2.2 cm Black Scr ew #10 x 2.2 cm Black Screw s - 2 #10 x 2.
4 3 • Slide a seat bottom tube thr ough each set of plastic rings on the seat bottom. 2 • Place the seat bottom face down on a flat surface. • At an angle, fit the footr est on the seat bottom, as shown.
5 5 Assembly 5 Insert Scr ews Her e Footrest • Insert two #1 0 x 2.2 cm black screws thr ough the footrest and into the seat bottom. Tighten the screws. #1 0 x 2.2 cm Black Screw - 2 6 • T urn the seat bottom assembly upright. • Fit the seat back pins into the openings in the top side of the seat bottom assembly .
6 6 6 Assembly 9 Screw Retainer - 2 #1 0 x 2.2 cm Black Screw - 2 • P osition a fr ame so that the decorated side is outwar d. • Insert the back leg of a fr ame into the back base. • Fit a screw r etainer over the hole in the back base, as shown.
7 7 7 Assembly 12 Front Leg Holes Screw Retainer - 2 #10 x 2.2 cm Black Scr ew - 2 • Insert the fr ame front legs onto the fr ont base. • Fit a scr ew retainer over a hole in the fr ont leg. • Insert a #1 0 x 7 / 8 " (2.2 cm) black screw thr ough the screw retainer and fr ont leg.
8 8 8 Assembly Back and Bottom View Seat Bottom Tube Ends 14 Seat Height Adjuster s • Fr om the back and bottom of the assembly , insert a #8 x 1.9 cm screw thr ough both seat height adjusters and the ends of the seat bottom tube. Tighten the screws.
9 Assembly Shoulder P ortion 16 • Insert the cr otch belt through the slot in the pad. Make sur e the crotch belt is not twisted. • Fold the top of the pad down. • Remove the shoulder portion of the waist/shoulder belts by feeding them through the slots in the seat back.
10 Battery Installation 1.5V x 3 "AA" (LR6) Battery Compartment Shown Actual Size • Loosen the scr ews in the battery compartment. Remove the battery compartment door . • Insert thr ee “ AA ” (LR6) alkaline batteries. • Replace the battery compartment door and tighten the screws.
11 11 Securing Y our Child IMPORTANT! Before each use, inspect this pr oduct for damaged hardwar e, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or br oken. Contact Mattel for replace- ment parts and instructions if needed.
12 12 Securing Y our Child 4 • To tighten the s houlder belts: Hold the adjuster and pull the front shoulder str ap down. • To loosen the s houlder belts: Slide the adjuster down. Note: After adjusting the restr aint system to fit your child, make sure you pull on it to be sur e it is securely fastened.
13 Prevent serious injury or death fr om falls or sliding out. The child should at all times wear a saf ety harness correctly fitted and adjusted. The tra y is not designed to hold the child in the chair . W ARNING 7 • Fit the base tr ay onto the seat armrests.
14 11 Release Bar Base Tr ay • While pushing the r elease bar on the front of the base tr ay , pull the tray base towar ds you and remove. • Insert the tab on the edge of the electr onic toy into the groove in the front of the base tr ay . • Push the electr onic toy down to secure in place.
15 Prevent serious injury or death fr om falls or sliding out. It is recommended that the high chair be used in the upright position only b y children capable of sitting upright unassisted.
Storage Storage 19 Base Tr ay • Fit the holes on the base tr ay latches onto the pegs on the back of the high chair frame. • Fit the electr onic toy to the tab on the back of the high chair , as shown. Pe g Hole 20 Pull Frame Release Latch • With the legs all the way open, lower the seat to position 7 the lowest position).
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Fisher-Price H7182 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Fisher-Price H7182 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Fisher-Price H7182 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Fisher-Price H7182 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Fisher-Price H7182, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Fisher-Price H7182.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Fisher-Price H7182. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Fisher-Price H7182 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
