Manuale d’uso / di manutenzione del prodotto TID-320T del fabbricante Farenheit Technologies
Vai alla pagina of 25
TID-320/ TID-320T In-Dash 3.2” Monitor T ouch Sensor DVD/MP4/ CD MW/FM Radio Built-in NTSC tuner Owner’s Manual Take the time to read thro ugh this ow ner’s manual. Familiarity with installation and operati on pr ocedures will help you obtain the best Performance from your new DVD-receiver.
Page - 1 Table of Contents Table of Contents............ .................................... .................................... .......................... ....... ..1 Important Safeguards........................ ....................................
Page -2 Important Safeguards z Using the device at temperature below -10 ℃ may cause the break age of the device. BEFORE USING PLEASE HEAT UP TH E PASSENGER COMPARTMENT TO THE RECOMM ENDED TEMPERATURE! z Read carefully through this manual to familiarize yourself with this high-qualit y sound system.
Page - 3 Accessories Package contains the following accessories for instal lation and operation of t he unit. (1) W asher , S pring W asher , M5 Nut 1 each (2) Mounting S trap 1 (3) Screw 1 (4) Bolt 4.
Page -4 Installation/Un-Installation First complete the electrical connections, and then check them for correctness. Installation This unit can be installed in any dashboard having an opening as shown on the pictu re. The dashboard should be 4.75 – 5.
Page - 5 Wiring Connections Make sure you have good chassis ground. A good ground connection will eliminate most electrical noise problems. A good chassis ground requires a tight connection to the vehicle’s metal chassis.
Page -6 Detachable Control Panel Detaching the control panel z Turn the Power of f. z Press OPEN button release the panel. z Pull the panel out. Attaching the co ntrol panel z Insert the left side of the control panel into the m ain unit. z Press the control panel right side until the “click” sound is heard.
Page - 7 Inner Panel 17. M emory C ard s lot 18. Flash LED 19. RE SET 1. POWER/ MUTE 2. MODE 3. MENU 4. AS/PS 5. Volume Up (+) 6. NEXT 7. IR sensor 8. PREVIOUS 9. LCD 10. AV in jack 11. MEM/ 12. OK 13. OPEN 14. USB jack 15. BAND 16. Volume Down (-) 20.
Page -8 IR Remote Control REPLACIN G THE BA TTERY Remote Control comes with a CR-2025 Lithium Battery included. 1. Remove the Battery Holder from the back of the Remote Control. 2. Insert a CR-2025 Lithium battery with the positive (+) mark upward. Insert the Battery Holder into the back of the Remote Control.
Page - 9 General Oper ations Reset the Unit In case the unit is malfunctioned or need to reset to factory default setting, press RESET button in inner panel then the unit will be reset. Power on/of f Press “POWER” button to turn on the unit. Long press POWER button on front panel or press POWER button on RC to power off the unit.
Page - 10 Press / but tons on remote to adjust the audio setting data (or press the knob on front panel to adjust the setting data). Press SEL button on remote again to save the setting data and return to current mode. Notes: If turn off the power, all the settings of each mode will be saved.
Page - 11 z EXPERT MENU MENU DESCRIPTION DX Set search radio station by DX or LOCAL mode. DX → LOCAL STEREO Set radio audio at STEREO or MONO mode, STEREO → MONO BEEP Set press keys‘ sound.
Page - 12 Preset station 1-6 play and setting z Play preset station: to play the preset station 1-6, you can press number key 1-6 on remote control, Preset station setting: during manual t urning or a.
Page - 13 GOTO Functi on Long press AUDIO/GOTO button on remote control to show GOTO menu, use 0-9 to input tra ck/ time to go to directly. Fast Forward and Backward Press the / buttons and hol.
Page - 14 Changing the Subtitle La nguage (only for MP4 files) Press SUB-T button on the remote to select the pr eferred language for sub-title. ZOOM (only for MP4 files) Press ZOOM button and hold fo.
Page - 15 Picture file: JPEG (*.jpg) z ISO 9660 or IS O 9660 +Joliet format - Max. 30 characters z Max. Track number is 448 z Max. nested directory is 8 levels z The max. album number is 99 z The max. length of each track i s 99 minutes 59 seconds z Supported sampling frequency for MP3 disc: 8 KHz to 4 8 (44.
Page - 16 Repeat playback Press the RPT/P.SCN button on the RC once or more times to repeat the playback: - For VCD/CD: display appears Repeat Track => Repeat Disc => Off (Some discs do not support this functions).
Page - 17 Selecti ng different audio modes z For DVD disc: pr ess AUDIO on the RC repeatedly to select the audio language to listen (if the disc supports multi-language mode). z For VCD disc: press AUDIO on the RC repeatedly to select the follo wing modes: L R STEREO (Channel left => Channel right => Stereo).
Page - 18 Notes on creating your o wn CD-R or CD-RW containing M P3 files: z To enjoy high quality sound, we recommend converting to MP 3 files with a sampling frequency of 44.1 kHz and a fixed bit rate o f 128 kbps. z DO NOT store more than 448 MP3 files per disc.
Page - 19 Channel Select this menu item is to set your desired searching channel, press cursor left/right buttons on remote control to select one. Fine Select this menu item is to fine TV picture and s ound until it achieves the best quality, pr ess cursor left/right buttons on remote control to adjust .
Page - 20 Rating For DVD discs which support rating system, setting up rating control can prevent children from watching content that might not be suitable to their age.
Page - 21 Video Setup: Brightness With this menu item you c an set up the brightness of the image. Contrast With this menu item you c an set up the contrast of the image. Hue With this menu item you can set up the hue. Saturation With this menu item you c an set up the color saturation.
Page - 22 Note on Discs Only use groundless loudspeakers. Use only loudspeakers of minimal 40W att, using fewer watts may result in damaging your loud speakers at higher volumes. Use 4~8 Ω (Ohm impedance) loudspeakers only; using higher or lesser impedance may damage the unit.
Page - 23 T roubleshooting guide Symptom Cause Solution General No power The car ignition is not on. The fuse is blown. If the power supply is properly connected to the car accessory switch the ignition key to “ACC”. Replace the fuse. Disc Disc cannot be loaded.
Page - 24 Specification General Power supply: 12 V DC Current consumption: max. 10 A Maximum power output: 40W x 4 channels Compatible formats: DVD/SVCD/VCD/HDCD/MP3/MP4/WMA /CDDA/Picture-CD/ JPEG/ CD-R/ -RW/D VD±R/±RW playback Dimensions (W x D x H) / weight: 178 x 175 x 50 mm / 1.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Farenheit Technologies TID-320T è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Farenheit Technologies TID-320T - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Farenheit Technologies TID-320T imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Farenheit Technologies TID-320T ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Farenheit Technologies TID-320T, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Farenheit Technologies TID-320T.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Farenheit Technologies TID-320T. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Farenheit Technologies TID-320T insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
