Manuale d’uso / di manutenzione del prodotto XPA 2003C-70V del fabbricante Extron electronic
Vai alla pagina of 33
User Guide XTRA ™ Full Rack Series: Audio Products Full-Rack 2-, 3-, and 4-Channel Mono and Ster eo Audio Power Amplifiers 68-783-01 Rev . C 05 11 XP A 2002 XP A 2003C-70V XP A 2002-70V XP A 2003C-.
This symbol is intended to alert the user of important operating and mainte- nance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’ s enclosure that may present a risk of electric shock.
FCC Class B Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pr ovide r easonable protection against harmful interfer ence in a r esi- dential installation.
Conventions Used in this Guide In this user guide, the following are used: NOTE: A note draws attention to important information. TIP: A tip provides a suggestion to make working with the application easier . CAUTION: A caution indicates a potential hazard to equipment or data.
Contents Introduction ........................................................... 1 About this Guide ................................................ 1 T erms Used in this Guide ................................. 1 Features ............................
Intr oduction About this Guide This guide contains information about the Extron ® series of audio power amplifiers: the XP A 2002 two-channel ster eo amplifier , the XP A 2002-70V two-channel, 70 V.
Featur es Extron Patented Class D Ripple Steering (CDRS ™) technology — CDRS is an Extr on patented technology that provides a smooth, clean audio waveform and an impr ovement in signal fidelity over conventional Class D amplifier designs.
Installation This section discusses how to install the XTRA Series of full rack power amplifiers. WARNING: Installation and service must be performed by authorized personnel only (see “ UL Rack Mounting Guidelines )”.
COMPUTER IN VIDEO OUT REMOTE I N P U T S 1 2 3 4 5 10 7 11 8 9 6 13 12 14 7 9 11 8 10 12 RESET LAN ACT LINK 9 11 13 10 12 14 PASS THROUGH S-VIDEO VIDEO Y C Y/V ID C VIDEO IN AUDIO INPUTS COMPUTER OUT .
RS -2 32 Lapt op 100-240V 50/60 Hz 1.3A MAX 1 2 3 80 Hz OFF CH 3 1 2 4/8 Listed 17TT AUDIO/VIDEO APPARATUS 3 70V LEVEL REMOTE LIMITER/ PROTECT SIGNAL STANDBY INPUTS OUTPUTS CLASS 2 WIRING XPA 2003C -7.
LAN 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 9 10 11 12 INPUTS RESET H SYNC V SYNC OUTPUTS 1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 6 7 8 INPUTS OUTPUTS R G B H V R G B H V 100-240V 0.5A 50-60Hz INPUTS DIGITAL OUTPUTS SSP 7.1 1 2 3 5 ANALOG FRONT CENTER SIDE BACK RS-232 Tx Rx SUB WOOFER 4 L R L R L R L R 100-240V 50/60 Hz 1.
Operation This section discusses how to operate the XP A power amplifiers. T opics that ar e covered, include: Front Panel Featur es and Operation Rear Panel Features and Operation .
a Power indicator LED — This LED lights: Green when the amplifier is r eceiving full power . Amber when the amplifier is in Standby mode. Standby mode turns off all outputs from the amplifier , although the amplifier is still receiving power (see d of “ Rear Panel Features and Operation ) .
Rear Panel Featur es and Operation OUTPUTS CLASS 2 WIRING 1 12 2 (BRIDGE A) ON OFF 12 LEVEL REMOTE LIMITER/ PROTECT SIGNAL STANDBY INPUTS XPA 2002 BRIDGE MODE BRIDGE 8 ONLY ( ) 4 / 8 12 BRIDGE GREEN - ACTIVE AMBER - STANDBY 100-240V 1.
OUTPUTS CLASS 2 WIRING 1 123 4 2 3 (BRIDGE A) (BRIDGE B) 4 ON OFF AB 12 34 LEVEL REMOTE LIMITER/ PROTECT SIGNAL STANDBY INPUTS XPA 2004 BRIDGE MODE BRIDGE 8 ONLY ( ) 4 / 8 BRIDGE 8 ONLY ( ) 4 / 8 123 4 BRIDGE A BRIDGE B GREEN - ACTIVE AMBER - STANDBY 100-240V 1.
g Level adjustment (channels 1, 2, 3 and 4) — Use a T weeker or small screwdriver to adjust the audio input level for the corresponding channel. The analog potentiometers control the level fr om = (full attenuation) to 0 dB (no attenuation).
i High pass filter toggle switch — Use a small screwdriver to toggle this r ecessed two-position toggle switch that alternates between Off (no filtering) and 80 Hz. The XP A 2002-70V and XP A 2002-100V have 2 switches, one for each output channel.
Step 1: Strip and inse rt the speak er wires into the connector and tighten the captive scre ws . Be sure to obser ve correct polarity . Step 2: Inser t the wired connector into the amplifier output and secure the locking scre ws on either sid e.
Step 1: Strip and inse rt the speak er wires into the connector and tighten the captive scre ws . Be sure to obser ve the correct polarity . Step 2: Inser t the wired connector into the amplifier output and secure the locking scre ws on either sid e.
Bridged Mode Output XP A 2002 bridged mono output speaker wiring In bridged mode, the output mode toggle switches for Input 1 (A) or Input 3 (B) or both must be set to the bridged (up) position, as shown below .
XP A 2004 bridged mono output speaker wiring In bridged mode, the output mode toggle switches for Input 1 (A) or Input 3 (B) or both must be set to the bridged (up) position, as shown below .
On the input end, only Input 1 or Input 3 or both is used in bridged mode, as shown below . 34 2 1 INPUTS XTRA Full Rack Power Amplier Series • Operation 17.
Refer ence Information This section discusses the specifications, part numbers, and accessories for the XTRA Series of audio power amplifiers. T opics that are cover ed, include: Specifications Part Numbers Mounting Specifications Audio V oltage gain XP A 2002, XP A 2004 .
Audio output Number/signal type XP A 2002 ................................ 2 channels, 4 or 8 ohms; or 1 bridged mono, 8 ohms XP A 2002-70V ......................... 2 channels, 70 V XP A 2002-100V ....................... 2 channels, 100 V XP A 2003C-70V .
S/N ................................................. 100 dB, 20 Hz - 20 kHz, unweighted Damping factor XP A 2002-70V ......................... >100 @ 25 ohms XP A 2002-100V ....................... >100 @ 50 ohms XP A 2003C-70V Channel 1 or 2 ..
Power consumption at 230 V AC, 50 Hz T ypical (1/8 power) XP A 2002 ........................... 4 ohms (x2): 85.6 watts 8 ohms (x2): 54.4 watts XP A 2002-70V ................... 70 V (x2): 85.6 watts XP A 2002-100V ................. 100 V (x2): 90.4 watts XP A 2003C-70V .
XP A 2004 ........................... 29.0 watts (99 BTU/hr) 1/8 power XP A 2002 ........................... 4 ohms (x2): 35.6 watts (122 BTU/hr) 8 ohms (x2): 29.4 watts (100 BTU/hr) XP A 2002-70V ................... 70 V (x2): 35.6 watts (122 BTU/hr) XP A 2002-100V .
Part Numbers Included Parts These items are included with each power amplifier , as indicated below . Included parts Replacement part number XP A 2002 2-channel low impedance power amplifier or XP A.
Optional Accessories Description Part Number SI 3CT LP Ceiling speakers 42-103-03 SI 3C LP Ceiling speakers 42-103-13 SI 3 Surface mount speakers (black, white) 42-105-02, -03 SI 26CT Ceiling speakers.
Mounting The XP A power amplifiers can be set on a table; mounted on a rack shelf; mounted under a desk or other furniture; or mounted in the plenum space above a ceiling-mounted projector . T abletop Use Four self-adhesive rubber feet are included with the audio amplifier .
100-240V 50/60 Hz 1.3A MAX 1 1 2 3 4 2 3 (BRIDGE A) (BRIDGE B) BRIDGE 8 ONLY 4 ON OFF ( ) A B 1 2 BRIDGE A 3 4 BRIDGE B L iste d 17TT AUDI O/VI DEO APP ARA TUS LEVEL REMOTE LIMITER/ PROTECT SIGNAL INPUTS OUTPUTS CLASS 2 WIRING XPA 2004 BRIDGE MODE 1 0 2 0 3 0 4 0 4 / 8 4 / 8 BRIDGE 8 ONLY ( ) ST ANDB Y Mounting Ear uses 5 screws (ea side).
100-240V 50/60 Hz 1.3A MAX 1 1 2 3 4 2 3 (BRIDGE A) (BRIDGE B) BRIDGE 8 ONLY 4 ON OFF ( ) A B 1 2 BRIDGE A 3 4 BRIDGE B List ed 17TT AUDI O/V IDEO APP ARA TUS LEVEL REMOTE LIMITER/ PROTECT SIGNAL INPUTS OUTPUTS CLASS 2 WIRING XPA 2004 BRIDGE MODE 1 0 2 0 3 0 4 0 4 / 8 4 / 8 BRIDGE 8 ONLY ( ) STANDBY 100-240V 50/60 Hz 1.
Extr on ® W arranty Extron Electr onics warrants this pr oduct against defects in materials and workmanship for a period of three years from the date of pur chase.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Extron electronic XPA 2003C-70V è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Extron electronic XPA 2003C-70V - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Extron electronic XPA 2003C-70V imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Extron electronic XPA 2003C-70V ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Extron electronic XPA 2003C-70V, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Extron electronic XPA 2003C-70V.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Extron electronic XPA 2003C-70V. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Extron electronic XPA 2003C-70V insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
