Manuale d’uso / di manutenzione del prodotto DMP 64 del fabbricante Extron electronic
Vai alla pagina of 146
68-1790-01 Rev. C 04 13 Digital Matrix Processor DMP 64 User Guide Audio Products Mixers and Processors.
Precautions/Safety Instructions ii FCC, Copyright, and T rademark Information iii Safety Instructions • English WARNING: This symbol, , when used on the product, is intended to alert the user of the presence of uninsulated danger ous voltage within the product’ s enclosure that may present a risk of electric shock.
FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part15 of the FCC rules. The ClassA limits provide r easonable protection against harmful interference when the equipment is operated in a commer cial environment.
Document Conventions Conventions Used in this Guide Notifications The following notifications are used in this guide: DANGER: A danger indicates a situation that will result in death or sever e injury . W ARNING: A warning indicates a situation that has the potential to result in death or severe injury .
Contents v DMP64 • Contents Introduction ................................................... 1 About This Guide ............................................. 1 About the DMP64 Digital Matrix Processor ..... 1 Features .........................
DMP64 • Contents vi Presets .......................................................... 81 Previewing and Recalling a Pr eset ............. 81 Building a Preset ........................................ 82 Protected Configuration ..................
Intr oduction This section describes this manual and the DMP64, including: • About This Guide • About the DMP64 Digital Matrix Processor • Features • DMP64 Application Dia.
Featur es • Consumer and professional audio compatibility — Input and output line level can be set to consumer (–10dBV) or professional (+4dBu). • Inputs — Six balanced or unbalanced mic/line on 3.5 mm, 3-pole captive screw connectors.
• Group masters — The DMP64 pr ovides the capability to consolidate gain or mute control thr oughout the system. Any gain or mute block within the Graphical User Environment can be selected and added to a gr oup master , which can then be controlled by a single master fader and mute contr ol.
DMP64 Application Diagram INPUT LAN POWER 12V 500mA MAX 1 2 3 4 COM 3 IR 3 S G S G TX RX 4 RELAY 3 4 COM1 TXRX RT SC TS COM 2 IR 1 S G S G TXRX 2 RELAY 1 2 100-240V 50/60 Hz 1.
Installation This section describes the installation of the DMP64, including: • Mounting the DMP64 • Rear Panel Features and Cabling Mounting the DMP64 The 1U high, half rack width, 9.
a Power connector — Connect the included 12 VDC external power supply into the 2-pole 3.5 mm captive screw connector . Be careful to observe the corr ect polarity . SECTION A–A Po wer Supply Output Cord Ridges A Smooth A Ridges Smooth 2-P ole Orange Captive Scre w Connector (12V) Tie Wrap 3/16” (5 mm) Max.
b Mic/Line 1-6 input connectors — 3-pole 3.5 mm double-stacked captive screw connectors accept balanced or unbalanced mono mic or line level signals. Mic/line inputs provide gain settings to accommodate consumer (–10dBV) and pr ofessional (+4dBu) operating line level sources, plus micr ophone level sour ces.
e Digital I/O output connectors — A double-stacked 4-pole 3.5 mm captive screw connector provides six configurable digital input or output ports allowing connection to various devices such as motion detectors, alarms, lights, LEDs, buttons, photo (light) sensors, or temperature sensors.
Har dwar e Operation This section describes the the operation of the DMP64, including: • DMP64 Operation • Front Panel Operation • Rear Panel Operation DMP64 Operation The DMP64 does not have physical controls.
Fr ont Panel Operation DMP 64 DIGIT AL MA TRIX PROCESSOR INPUTS CLIP SIGNAL 12 3456 CONFIG OUTPUTS CLIP SIGNAL 12 34 bc d a Figure 7. DMP64 Front Panel a Power LED — The power indicator lights when the DMP64 is operational. b Configuration connector — The USB 2.
Rear Panel Operation DMP 64 POWER 12V 1.0A MAX RESET LAN 123 456 4 5 6 1 2 3 4 Tx Rx G RS-232 (2) Tx Rx G RS-232 (1) 45 6 G 12 3 G MIC +4 8V 1 3 2 MIC/LINE INPUTS OUTPUTS I/O REMOTE ab cd ef gh i Figure 8. DMP64 Rear Panel a b d e f See Rear Panel Features and Cabling on page5 for details.
Reset Actuator and LED Indicator A recessed button ( h ) on the r ear panel initiates several r eset modes. The rear panel LED ( i ) blinks to indicate the reset mode.
MODE 4 — IP Address r eset: 1. Apply power to the DMP64. 2. Press and hold the r eset button about 6seconds until the r eset LED blinks twice. Release the reset button. 3. Within (1) second, press the reset button again to r eset the IP settings.
DMPSoftwar e This section describes the control softwar e for the DMP64, including: • Software Contr ol • Embedded W eb Pages • Windows-based Program Contr ol • DSP Configura.
Embedded W eb Pages The embedded web pages, accessible by LAN using a web browser , include the following information, available in a tabbed interface. • System Status — The opening web page, displaying a report of system status parameters. • Configuration — This tab contains the following menu items.
2. Click the Software tab or software icon. NOTE: If the DVD setup program does not start automatically , run Launch.exe from the DVD ROM dir ectory using Windows “My Computer”. Figure 10. DVD Softwar e Menu 3. Scroll to the DSP Configurator pr ogram and click the Install text to its right.
Install the USB Driver When the USB installer begins, follow these instructions. 1. When the driver installation window appears (see figure 12), click Next to pr oceed. Figure 12. USB Installer Splash Scr een 2. The driver installer launches (see figure 13).
3. When the installer has completed the installation of the USB drivers, the following screen appears (see figur e 14): Figure 14. Successful USB Driver Installation 4.
ab cd j hi fg e Figure 15. DMP64 Configurator Pr ogram The DSP Configurator program window consists of an input and virtual r eturn signal processor chain, the main mixer , virtual send and receive (secondary) mixers, and an output signal processing chain.
Navigation There ar e two methods of navigation ar ound the interface: • Keyboard • Mouse One element in the user interface always retains focus. When a new DSP Configurator file is opened, the upper left element (Input #1 Gain) is focused by default.
As shown below , the starting point for the paste, (the upper , leftmost element), must first be focused by left-clicking the mouse on it. Note the green focus outline that appears on the Mic #4 Gain block. The clipboard elements ar e pasted using the context menu Paste command, the Edit>Paste command, or <Ctrl+V>.
DSP Configurator T oolbar Menus The DSP Configurator contains the following structural menus, arranged horizontally below the title bar: File NOTE: New , Open , and Recent Files are unavailable in Live mode. • New — Discards the curr ent DSP configuration (after pr ompting to save any changes) and opens a blank configuration file.
View • Meter Bridge — Opens a Meters dialog box with real-time meters that monitor signal levels at each input and output. NOTE: Meter Bridge is available in Live mode only while connected using the LAN port.
• Configure Digital I/O Ports — Live mode only . Opens a utility to configure digital I/O ports. The DMP64 provides six digital I/O ports that can be used to trigger external events from DMP64 actions, or for external events to trigger DMP actions (see Digital I/O Ports on page75).
• Processor Defaults, Reset All Defaults — Returns the DMP64 processor and level control blocks to factory default settings. Each processor and gain/volume/trim block also has an individual default reset. • Processor Defaults, Defaults — Individually selects the default parameters for the various processor , trim, and gain blocks.
Presets Dr op-down Displays a list of up to 32 presets. Select a pr eset fr om the list to display it in the window and either activate it ( Recall ), abort the selection without either recalling or deleting it ( Cancel ), or delete it ( Delete ).
ab cd j hi fg e Figure 17. Contr ol Blocks and Pr ocessor Chains Audio Level, Mix-point, Pr ocessing Blocks, and Signal Chains Outlined in red above (see figur e 17), all contr ol blocks on the main D.
Level Control Blocks T o access a gain, trim or volume control to view a setting, make a change, or observe a live audio meter (input gain and output volume blocks only), double-click the gain block icon (see figure 19). This action opens a dialog box that contains the fader for that contr ol.
Once a processor is inserted, to view associated parameters that define the selected processor (such as a fr equency curve) or to r emove the bypass, double-click on the processor block. This action opens a new window with a dialog box that contains parameters for the processor (see figur e21).
Mic/Line Input Signal Contr ols The input signal processor chain allows adjustments to pr ogram or micr ophone audio material before input to the main mixer . Gain Control (GAIN) The gain control pr ovides a single long-thr ow fader with a range of –18dB to +80dB, adjustable in 1 dB increments with the fader , or in 0.
Filter (FIL T) Each filter block allows a total of five filters. The first filter is inserted from a pr ocessor list that appears when the block is double-clicked or from a context window that shows a processor list when the block is right-clicked. Figure 22.
Figure 23. Filter Block Dialog Box Additional filters are inserted using the open filter block dialog box, and selecting a filter type from the dr op-down filter selection list.
Figure 24. Filter Dialog Box, Filters Added Within the dialog box, a filter is focused when a filter type is inserted, or is focused by clicking the filter number to the left of the filter selection drop-down list. Note how box3 (see figure 24) is highlighted in yellow , indicating it is the filter in focus.
Figure 25. Filter Dialog Box, Filter Not Bypassed Above the graph, each filter has a "handle" (circled in r ed above for the parametric EQ filter) placed directly above the cutof f or center fr equency . The handle number corresponds to the filter number (also outlined in r ed).
High Pass The high pass filter allows frequencies below the specified fr equency to pass unattenuated. All frequencies below the cutof f ar e attenuated.
Low Pass The low pass filter is the opposite of the High Pass filter . All frequencies above the specified frequency ar e attenuated allowing lower fr equencies to pass. Figure 27. Low Pass Filter Response Curve Here, the fr equencies higher than the specified fr equency , 10 kHz, are attenuated leaving the lower frequency r esponse flat.
Bass and T reble Shelving Bass and treble shelving can be added to the filter . Also known as shelving or tone controls, the separate bass and tr eble filters pr ovide the ability to cut or boost gain linearly above or below a selected frequency , with the end-band shape giving the visual appearance of a shelf.
Parametric (Equalizer) The parametric filter is a frequency equalizer that of fers contr ol of all parameters, including amplitude (the amount of gain [boost], or gain reduction [cut] applied), center fr equency (frequency), and range of af fected fr equencies (Q) around the center fr equency .
By increasing the Q to 10.000, the center fr equency r emains the same. The markers show the bandwidth of the filter narrowed to between 900Hz and 1200Hz, or about 300Hz (see figure 30). Parametric filters can be used to notch out a very narr ow , or very wide range of frequencies using the Q setting.
The overall frequency r esponse is now shown as a solid r ed line with the filter in focus (located in row 3 in figur e 31) shown in the color of its table r ow . Figure 31. All Parametric Filters Active The parametric filter allows frequency selection accurate to 0.
Feedback Suppressor (FBS) The Feedback Suppressor is used in live situations when ther e is an indication of feedback during live operation. Dynamic filters automatically detect feedback on a live microphone channel, and engage a set of up to 5 fixed and 15 dynamic filters to counteract frequency peaks at the detected feedback fr equency .
FBS Settings The Settings tab enables selection of the feedback suppressor parameters. • For Composite View show: — The graph view is set by one of three buttons: • Only Dynamic FBS Filter.
FBS Dynamic Filters This tab contains the fifteen dynamic filters, with a scroll bar to display filters hidden due to dialog box size. Dynamic filters are notch filters that ar e cut only , providing attenuation up to 30dB at the specified Q.
FBS Fixed Filters Fixed filters are notch filters with an adjustable center fr equency and Q, and up to 30dB of cut. The fixed filters are typically set by converting dynamic filters to fixed, however adjustments to filter parameters can be made manually from the Fixed Filters tab.
Dynamics (DYN) A dynamics processor alters the dynamic range, the differ ence between the loudest to the quietest portions, of an audio signal. Each input channel provides two dynamics processor blocks that, when inserted, pr ovide one of four types; AGC, Compressor , Limiter , or a Noise Gate processor .
Automatic Gain Control (AGC) AGC adjusts the gain level of a signal based upon the input strength to achieve a mor e consistent volume. Below the set threshold, the signal is not af fected. Above the thr eshold, weaker signals are boosted up to the maximum gain setting to r each a user -defined target level.
Compressor The compressor r egulates signal level by r educing (compressing) the dynamic range of the input signal above a specified threshold. The input level to output level ratio determines the reduction in the dynamic range beyond the thr eshold setting.
Limiter The limiter restricts the input signal level by compr essing its dynamic range above a specified threshold. The limiter is most commonly used to pr event clipping, pr otecting a system against component or speaker damage.
Noise Gate The noise gate allows an input signal to pass only when it exceeds a specified threshold level. Above the threshold level, the signal passes unpr ocessed. Below the thr eshold the signal is attenuated at the rate set by the ratio adjustment.
Delay (DL Y) The delay processor , when inserted, provides a means to delay the audio signal. Audio delay syncs audio to video or can time-align speakers placed at differ ent distances fr om the listener . The DMP64 can set delay by either of two criteria: time or distance (feet or meters).
Ducking (DUCK) Ducking provideds a means to duck, or lower , the level of one or more input signals when a specified source must take pr ecedence. The ducking processor block, when inserted, pr ovides a means to duck one or more mics and pr ogram material (ducking targets) when the pr ocessor detects a signal from the ducking sour ce.
Ducking Configuration Ducking is configured in a dialog box that opens when an active ducking pr ocessor block is double-clicked (see figure 37 on the pr evious page). a Current sour ce indicator Shows the input selected as the ducking source. Ducker settings af fect the input channel shown here.
Ducking Priority Multiple levels of ducking can be requir ed enabling an input sour ce to take precedence over all but one other input. In this example, inputs 2 through 6 ar e set to duck when Input #1 has a signal above the ducking threshold. Input#2 is set to duck inputs 5 and 6.
T o set an additional ducking source: 1. Insert a ducking processor on the additional ducking sour ce. In this example, input #2 is the second ducking source, with input#1, as shown above, as the first source. NOTE: Since it was previously selected as a ducking target, Input#1 is not available as a target of input #2.
Pre-mixer Gain (GAIN) The post-input processing gain contr ol (also called the pr e-mixer gain) provides gain or attenuation post-pr ocessing gain block. It includes a mono long-throw fader with a – 100.0 to +12.0dB gain range, and a current level setting r eadout below the fader .
Line Output Channels There ar e four mono line output channels. Contr ols and processing blocks, identical for each output channel, are described in the following sections. Loudness (LOUD) The loudness processor , when inserted, applies a filter compensation curve to the signal in an inverse relationship to the output volume contr ol setting.
Calibrating Loudness The user can fine-tune the amount of loudness compensation using the compensation adjustment slider and adjusting "by ear ," or by measuring SPL levels in a particular room, then using the slider to adjust the loudness filter relative to the SPL of the r oom and system gain structure.
3. Set the Calibrate slider to 0, the center point. Disengage the loudness Bypass . The result is a moderate enhancement to the pr ogram material, with mor e accentuated bass frequencies (below 500Hz), and mor e brightness in the high fr equencies that carry harmonic content (above 7kHz).
V olume Control (VOL) Each output channel volume block provides a mono long-thr ow fader with a range of 0 to 100dB of attenuation, and a volume setting readout (indB) below the fader . V olume level is adjustable with the slider or by entering the desired level dir ectly into the volume setting readout in 0.
Virtual Bus Returns There ar e four mono virtual bus r eturn inputs, fed by the virtual bus sends. Channel controls and pr ocessing blocks described in the sub-sections that follow ar e identical for each virtual bus return channel, A through D. The virtual bus is used when additional processing of an input signal is r equir ed.
Primary Mix Matrix The DSP architectur e contains a primary mix matrix that connects the mic/line inputs and virtual bus returns to the line outputs. The DSP Configurator user interface provides control of the primary mix matrix, used to set mix levels fr om the post pr ocessing inputs and post processing virtual r eturns to each line output bus.
Mix-point Behavior: No mix information — A faint gray circle on the mix-point indicates it is muted (contains no mix information). Mix information — A solid teal-colored cir cle indicates the mix-point contains mix information (the mix-point is unmuted).
Clicking a mix-point brings focus to that mix-point. A circle appears ar ound the teal mix-point which remains transpar ent. Double-clicking a mix-point opens a configuration dialog box with the following components: • Mono Fader — Sets the signal level from the selected input to the output bus.
Mix-point Examples In order to better understand how mix-points work, the following diagrams pr ovide examples of differ ent mix setups. Mic/Line Input 1 Mic/Line Input 2 Mic/Line Input 3 Mic/Line Inp.
Mic/Line Input 1 Mic/Line Input 2 Mic/Line Input 3 Mic/Line Input 4 Mic/Line Input 5 Mic/Line Input 6 A B C D 1 2 3 4 5 6 AB CD 1 2 3 4 Outputs Vir tual Bus Send Vir tual Bus Return FI LT DL Y LOUD DY.
Mic/Line Input 1 Mic/Line Input 2 Mic/Line Input 3 Mic/Line Input 4 Mic/Line Input 5 Mic/Line Input 6 A B C D 1 2 3 4 5 6 AB CD 1 2 3 4 Outputs Vir tual Bus Send Vir tual Bus Return FI LT DL Y LOUD DY.
Secondary Mix Matrix The DSP architectur e contains a secondary mix matrix that connects the mic/lineinputs and virtual bus return signals to the virtual bus sends.
In the example below (see figure 45), input 1 is sent to the virtual bus send by muting all four signals on the input1 primary mix-points. The virtual bus now serves as additional signal processing for the input.
Gr oup Masters There ar e 32 Gr oup Masters that can each be configured to simultaneously contr ol up to 16 group members. Gr oup masters ar e configured in the DSP Configurator pr ogram and saved in the device. Working in emulate mode, gr oup masters can be saved in a configuration file and pushed to the device upon connection.
Figure 46. Sample Fader Gr oup Master and Associated Gain Contr ols Mute controls within the blocks can also be gr ouped (see figur e 47). Figure 47. Sample Mute Gr oup Master and Muted Outputs DMP.
Configuring a Group Master Configure a gr oup as follows: 1. Click Tools > Configure Groups to open the Configure Gr oups dialog box, or click View > Group Controls and then click the Add a Group menu selection. 2. In the Select Group drop-down box, click a gr oup to select it (see figur e 48).
Deleting a Group Master T o delete a group: 1. Click Tools > Configure Groups to open the configure gr oups dialog box or click View > Group Controls and then click Add a Group . 2. In the Select Group drop-down box, click a number ed gr oup (such as "Group #1") to select it.
T ools The T ools menu contains three selections: • Clear All Groups - clears all gr oup members and gr oup master parameters. • Increment/Decr ement Simulator - allows the user to test incr ement/decrement values, see below for more information.
Group Details Report Select Tools > Group Details Report to create a Micr osoft W ord file that details all created gr oups (see figur e 51). GROU P DET AILS REPOR T Group #1 P rocessor T ype: Outp.
Digital I/O Ports The DMP64 provides six digital I/O ports that can trigger external events from DMP64 actions, or allow external events to trigger DMP64 actions. The DSPConfigurator software pr ovides pr e-configured scripts with a fixed set of common trigger and event combinations.
Reinitialize Digital I/O Should the script stop running for any reason, select Tools > Configure Digital I/O , then select Reinitialize Digital I/O . This option is only available in Live mode. T o remove a digital I/O script fr om the DMP64: Only one digital I/O configuration can be active at a time.
Selecting Live Mode and Pushing or Pulling Data T o switch from Emulate mode to Live mode: 1. Select the desired connection to the DMP64 and make the pr oper connections. NOTE: Extron r ecommends connection with the Ethernet LAN port when using DSPConfigurator .
5. If RS-232 is selected in step 3 : a. Click the com port dr op-down list and select the PC comm port connected to the rear panel RS-232 port. b. Check the baud rate displayed in the Com Port selection window . If the baud rate does not match the device’ s rate, click the Baud Rate drop-down menu and select the desired baud rate.
7. Click either the: a. Pull radio button to configur e the DSP Configurator pr ogram to match the device — proceed to step 9 -or - b. Push radio button to configure the device to match the DSPConfigurator program — pr oceed to step 8 9 9 8 8a 10 8c 8e 8f 8d 7a 7b -or- 8b 8d Figure 53.
8. T o push all of the DSP Configurator gain and processor block adjustments (configuration), and all presets to the DMP64, pr oceed to step 9. T o tailor the push (push only the configuration, only the presets, or the configuration and selected presets), click the Advanced button and pr oceed to step 8a.
Pr esets Presets r ecall a gr oup of frequently used settings. Pr esets created by DSPConfigurator can contain all elements (gain blocks, processor blocks, and mix-points) or a portion of the elements available within the program.
Building a Preset Only elements of the preset highlighted (given focus) ar e saved as a pr eset. <Ctrl + A> highlights all elements within the DSP Configurator . T o build a preset, highlight the desir ed DSP Configurator elements (gain and pr ocessor blocks, and mix-points) using standard keyboar d and mouse actions as follows: 1.
Managing Presets Once a preset is cr eated (whether or not the DSPConfigurator file is saved), it appears in the preset list, available fr om the DSPConfigurator user interface. In Live and Emulate mode, after a preset is selected fr om the list, action buttons become available next to the presets bar .
Pr otected Configuration A protected configuration is secur ed with PIN pr otection. The protected configuration can be recalled by any user , but can only be written or overwritten using the assigned 4-digitPIN.
DSP Configurator W indows Menus The DSP Configurator program is fully navigable using the computer keyboar d. Some keyboard navigation behavior matches Windows standards, while other behaviors ar e specific to DSP Configurator .
• Shift+T ab key combination — Reverses the direction of the <T ab> key function. • Arrow ( , , , and ) Keys — Navigate up, down, left, and right within any of the areas outlined in figur e 56. • Enter Key — Performs the same action as a mouse double-click.
4. T o highlight another element or group of elements, r epeat steps 2 and 3 as r equired. 5. T o cut or copy , press the <Ctrl+X> or <Ctrl+C> key combination. 6. T o save a preset , pr ess <Alt +T>, <Right Arr ow>, <Down Arrow>, then <Enter>, (see figure 57 below ) .
Optimizing Audio Levels The DMP64 uses floating point DSP technology , processing data using a combination of 32- and 64-bit algorithms. The analog to digital converters (ADC) and digital to analog converters (DAC) sample at 48kHz with 24-bit resolution.
About Setting Gain Structure There ar e two appr oaches the system designer can take in setting up gain structure, depending upon where output volume is to be contr olled.
Adjusting Pre-mixer Gain After setting input gain, add desired pr ocessors into the input signal chain (see figur e 58 on page 88). The pre-mixer gain contr ol ( b ) is used to compensate for level changes due to processing. Adding a compr essor generally r educes the signal level, while a filter can boost or cut the overall signal level.
Setting Mic/Line Input and Mix Levels In this example, the mic/line input 1 signal is sent to output 1 (see figure 58 on page 88). T o set the mic/line input and mix levels: 1.
SIS Pr ogramming and Contr ol This section describes SIS programming and contr ol of the DMP64, including: • Connection Options • Host-to-device Communications • Command and Response.
RS-232 Ports The DMP64 has two serial ports that can be connected to a host device such as a computer running the HyperT erminal utility or DataViewer . The ports make serial control of the switcher possible. Use the protocol information listed to make the connection.
T o establish a network connection to the DMP64: 1. Open a TCP socket to port 23 using the mixer IP address. NOTE: If the local system administrators have not changed the value, the factory-specified default, 192.168.254.254, is the correct value for this field.
Host-to-device Communications The commands listed in the following tables perform the same functions, but ar e encoded differ ently to accommodate the r equirements of each port (T elnet or browser). DMP64-initiated Messages The DMP64 initiates messages under specific conditions.
The Command and Response tables list valid ASCII (for T elnet or RS-232) command codes, the corresponding URL (Uniform Resour ce Locator) encoded (for W eb browsers) command codes, the DMP64 responses to the host, and a description of the command function or the results of executing the command.
Simple Control Port Commands - T elnet and Web-br owser Accessible Upper and lower case text can be used interchangeably except wher e noted. Port 23 is default for T elnet. Port 80 is default for Web br owser . They both can be mapped to differ ent ports.
Command and Response T able for Basic SIS Commands Command ASCII command (host to device) URL Encoded (web) Response (device to host) Information requests Firmware V ersion Q *Q X1!] Firmware and buil.
Command and Response table for basic SIS commands (continued) Command ASCII command (host to device) Response (device to host) Additional description IP Setup Commands Set unit name EX1@ CN } Ipn• X.
Command and Response table for basic SIS commands (continued) Command ASCII command (host to device) Response (device to host) Additional description Password and Security Settings Set administrator p.
Command and Response table for basic SIS commands (continued) Command ASCII command (host to device) Response (device to host) Additional description Serial Port Send Data String EX! * X1& * X2) *.
Command and Response table for basic SIS commands (continued) Command ASCII command (host to device) Response (device to host) Additional description Presets, I/O Names Write pr eset name EX1) , X1! N.
Command and Response T ables for DSP SIS Commands Many digital signal processor (DSP) functions; gain, mute, gr oup masters, and a pr otected configuration can be controlled using SIS commands. These commands follow the same general rules as basic SIS commands, but the variables ( X/ ) tend to be more complex.
Symbol definitions ] = CR/LF (carriage return/line feed) (hex 0D 0A) } = Carriage return (no line feed, hex 0D) (use the pipe character , | , for Web br owser commands) • = Space character | = Pipe .
Command and Response T able for DSP SIS Commands Command ASCII command (host to device) Response (device to host) Additional description Audio Level Control, and Mix-point Selection NOTE: The command .
Command and Response T able for DSP SIS Commands (continued) Command ASCII command (host to device) Response (device to host) Additional description Audio group master commands NOTE: • See Group Masters on page69, for more information about audio gr oup masters.
Command ASCII command (host to device) Response (device to host) Additional description Protected configuration NOTE: The DMP64 can save and recall a Personal Identification Number (PIN)-pr otected configuration, including mic mixes, parameters, variables, and values (with the exception of the device’ s IP address).
Command and Response table for DSP SIS commands (continued) c Main Mix-Point X6) c Main Mix-Point X6) Input 1 to Output 1 20000 Input 2 to Output 1 20100 Input 1 to Output 2 20001 Input 2 to Output 2 .
dB value X6! dB value X6! dB value X6! dB value X6! dB value X6! dB value X6! dB value X6! dB value X6! dB value X6! dB value X6! T able 2. Mix-point Gain Only - 35 . 0 1698 - 34 . 9 1699 - 34 . 8 1700 - 34 . 7 1701 - 34 . 6 1702 - 34 . 5 1703 - 34 . 4 1704 - 34 .
X6! — Mix-point gain ( c ), and Post-mixer trim ( d ) level values, (continued) dB value X6! dB value X6! dB value X6! dB value X6! dB value X6! dB value X6! dB value X6! dB value X6! dB value X6! dB value X6! T able 3. Post-mixer T rim and Mix-point Gain - 12 .
dB value X6! dB value X6! dB value X6! dB value X6! dB value X6! dB value X6! dB value X6! dB value X6! dB value X6! dB value X6! T able 4. Mix-point Gain Only + 12 . 0 2168 + 12 . 1 2169 + 12 . 2 2170 + 12 . 3 2171 + 12 . 4 2172 + 12 . 5 2173 + 12 . 6 2174 + 12 .
dB V alue X6@ dB V alue X6@ dB V alue X6@ dB V alue X6@ dB V alue X6@ dB V alue X6@ dB V alue X6@ dB V alue X6@ dB V alue X6@ dB V alue X6@ – 18 . 0 1868 - 17 . 9 1869 - 17 . 8 1870 - 17 . 7 1871 - 17 . 6 1872 - 17 . 5 1873 - 17 . 4 1874 - 17 . 3 1875 - 17 .
dB V alue X6@ dB V alue X6@ dB V alue X6@ dB V alue X6@ dB V alue X6@ dB V alue X6@ dB V alue X6@ dB V alue X6@ dB V alue X6@ dB V alue X6@ + 12 . 1 2169 + 12 . 2 2170 + 12 . 3 2171 + 12 . 4 2172 + 12 . 5 2173 + 12 . 6 2174 + 12 . 7 2175 + 12 . 8 2176 + 12 .
dB V alue X6@ dB V alue X6@ dB V alue X6@ dB V alue X6@ dB V alue X6@ dB V alue X6@ dB V alue X6@ dB V alue X6@ dB V alue X6@ dB V alue X6@ + 43 . 1 2479 + 43 . 2 2480 + 43 . 3 2481 + 43 . 4 2482 + 43 . 5 2483 + 43 . 6 2484 + 43 . 7 2485 + 43 . 8 2486 + 43 .
dB V alue X6@ dB V alue X6@ dB V alue X6@ dB V alue X6@ dB V alue X6@ dB V alue X6@ dB V alue X6@ dB V alue X6@ dB V alue X6@ dB V alue X6@ + 73 . 1 2779 + 73 . 2 2780 + 73 . 3 2781 + 73 . 4 2782 + 73 . 5 2783 + 73 . 6 2784 + 73 . 7 2785 + 73 . 8 2786 + 73 .
dB V alue X6# dB V alue X6# dB V alue X6# dB V alue X6# dB V alue X6# dB V alue X6# dB V alue X6# dB V alue X6# dB V alue X6# dB V alue X6# - 100 . 0 1048 - 99 . 9 1049 - 99 . 8 1050 - 99 . 7 1051 - 99 . 6 1052 - 99 . 5 1053 - 99 . 4 1054 - 99 . 3 1055 - 99 .
dB V alue X6# dB V alue X6# dB V alue X6# dB V alue X6# dB V alue X6# dB V alue X6# dB V alue X6# dB V alue X6# dB V alue X6# dB V alue X6# - 70 . 9 1339 - 70 . 8 1340 - 70 . 7 1341 - 70 . 6 1342 - 70 . 5 1343 - 70 . 4 1344 - 70 . 3 1345 - 70 . 2 1346 - 70 .
dB V alue X6# dB V alue X6# dB V alue X6# dB V alue X6# dB V alue X6# dB V alue X6# dB V alue X6# dB V alue X6# dB V alue X6# dB V alue X6# - 40 . 9 1639 - 40 . 8 1640 - 40 . 7 1641 - 40 . 6 1642 - 40 . 5 1643 - 40 . 4 1644 - 40 . 3 1645 - 40 . 2 1646 - 40 .
dB V alue X6# dB V alue X6# dB V alue X6# dB V alue X6# dB V alue X6# dB V alue X6# dB V alue X6# dB V alue X6# dB V alue X6# dB V alue X6# - 10 . 9 1939 - 10 . 8 1940 - 10 . 7 1941 - 10 . 6 1942 - 10 . 5 1943 - 10 . 4 1944 - 10 . 3 1945 - 10 . 2 1946 - 10 .
HTML Operation This section describes HTML operation and control of the DMP64, including: • Download the Startup Page • Status T ab • Configuration T ab • File Management T ab .
5. Press the keyboar d <Enter> key . The device checks to see if it is password- protected. a. If the device is not password-pr otected, it checks and downloads the HTML pages (proceed to step 7). b. If the device is password-pr otected, the device downloads the Connect to page (see figure 62).
Status T ab System Status Page The System Status page (see figure 63) pr ovides an overall view of the status of the device, including system information, power supply status, and serial port settings. The System Status page is the default page when establishing a connection to the device.
Configuration T ab System Settings Page Click the Configuration tab to download the System Settings page (see figure 64). The screen consists of fields to view and edit IP administration and system settings. Passwords and Firmwar e Upgrade pages ar e accessed by clicking the appropriate link on the left.
DHCP Selection The DHCP On selection directs the device to ignor e any enter ed IP addresses and obtain its IP address fr om a Dynamic Host Configuration Pr otocol (DHCP) server (if the network is DHCP capable). The DHCP Off selection turns DHCP off. Contact the local system administrator for additional information on your network.
Date/Time Settings Fields The Date/Time settings fields (see figure 65) pr ovide a location for viewing and setting the time functions. Figure 65. Date/Time Settings Fields Change the date and time settings as follows: 1. Click the desired variable box.
Passwords Page Access the Passwords page (see figure 66), by clicking the Passwords link on the system settings page. Figure 66. Passwor ds Page The fields on the passwords page ar e for entering and verifying administrator and user passwords. Passwor ds ar e case sensitive and limited to 12 uppercase and lower case alphanumeric characters.
Firmware Upgrade Page The Firmware Upgrade page pr ovides a way to verify the curr ent firmware version and to replace the firmwar e without taking the device out of service. Click the Firmware Upgrade link on the System Configuration page to access the Firmware Upgrade page (see figure 67).
5. Click Download to copy the firmware to your computer . 2 1 5 4 3 NOTE: The version, release date, and size shown ar e example values only . Download DMP64_FW1x01. exe DMP 64 Digital Matrix Processor Firmware for DMP 64 19-2247-50 V1.01 Ja nuary 17, 2011 2.
6. Click Run twice (see figure 69, f ). The PC downloads the firmwar e update fr om the Extron W eb site and starts the installation pr ogram to extract the firmware file. Fo lder where firmware is installed NOTE: T he version shown is a sample value only .
7. Click Next (see figure 69, g on pr evious page). The pr ogram extracts and places the firmware files in a folder identified in the InstallShield Wizard window . NOTE: Write down the folder wher e the firmwar e file is saved. 8. Click Finish (see figure 69, h ) to exit the pr ogram.
File Management T ab File Management Page T o delete files such as HTML pages from the connected device or to upload custom files to the device, click the File Management tab. The device downloads the file management HTML page (see figure 70). Figure 70.
Contr ol T ab Audio Settings Page The Audio Settings page provides a way to set the input audio gain and attenuation, output volume, and mix-point adjustments including level control, and mute or unmute. Access the Audio Settings page by clicking the Audio Settings link on the control page (see figure 71).
Mute and Unmute Inputs and Outputs Pressing the Mute button toggles mute on or of f. When muted, the Mute button is r ed and displays Muted. When unmuted it returns to gray and displays Mute. Mute and umute as follows: 1. Next to the desired input or output pr ess the Mute button to toggle mute on (button turns red) or off (button is gray ).
Change the Output V olume Level The output volume attenuates the signal from full volume down to 0 volume in 100 steps. Users can set individual output volume levels from a range of –100dB (full attenuation, minimum volume) to 0dB (no attenuation, full volume).
Presets Page The Presets page is used to save new pr esets cr eated on the Audio Settings page (see figure 74). Pr esets saved using this HTML page only include the gain contr ols on that page. However , presets created using DSPConfigurator include all signal pr ocessing blocks.
Refer ence Information This section contains refer ence information for the DMP64, including: • Firmware Loader • DMP64 Hardwar e Reset Modes • Mounting the DMP64 Firmwar e Loa.
The Firmware Loader scr een appears. 4 5 3. From the toolbar , select File>Open . 4. Locate the downloaded firmware file and click on it. 5. Click Begin on the main screen. The total pr ogr ess bar tracks the loading progr ess. 6. When the upload is finished, select File>Exit to exit the program.
DMP64 Har dwar e Reset Modes DMP64 Reset Mode Summary Mode Mode Activation Result Purpose/Notes Use Factory Firmware 1 Press and hold the r eset button, then apply power . NOTE: After a mode 1 reset, update the DMP64 firmware to the latest version.
Mounting the DMP64 The 1U high, half rack width, 9.5 inch deep DMP64 Digital Matrix Processor can be: • Set on a table, • Mounted on a rack shelf, • Mounted under a desk or tabletop, or • Mounted on a projector bracket. T abletop Use The DMP64 includes rubber feet (not installed).
Extron Headquarters +1.800.633.9876 (Inside USA/Canada Only) Extron USA - W est Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 F AX +1.919.850.1001 FAX Extron Europe +800.3987.6673 (Inside Europe Only) +31.33.453.4040 +31.33.453.4050 F AX Extron Asia 800.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Extron electronic DMP 64 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Extron electronic DMP 64 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Extron electronic DMP 64 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Extron electronic DMP 64 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Extron electronic DMP 64, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Extron electronic DMP 64.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Extron electronic DMP 64. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Extron electronic DMP 64 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.