Manuale d’uso / di manutenzione del prodotto ECM-3711 del fabbricante Evalue Technology
Vai alla pagina of 101
Part No. 2047371100R ECM-3711 Series VIA Eden V4 Micro Modul e User’s Manual 1 st Ed – 23 August 2006.
ECM-3711 Series 2 ECM-3711 Series User’s Manual FCC Statement THIS DEVICE COMPLIES WITH PART 15 FCC RULE S. OPERATION IS SUBJECT TO THE FOLLOWI NG TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE. (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CA USE UNDESIRED OPERATION.
User’s Manual ECM-3711 Series User’s Manual 3 Disclaimer Evalue Technology Inc. reserves the right to make changes, without notice, to any product, including circuits and/or software described or contained in this manual in order to improve design and/or performance.
ECM-3711 Series 4 ECM-3711 Series User’s Manual Technical Support We want you to get the maximum performance from your products. So if you run into technical difficulties, we are here to help. For the most frequently asked questions, you can easily find answers in your pr oduct documentation.
User’s Manual ECM-3711 Series User’s Manual 5 Product Warranty Evalue warrants to you, the orig inal purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase.
ECM-3711 Series 6 ECM-3711 Series User’s Manual Contents 1. Getting St arted ............................................................................................................ 9 1.1 Safety Prec autions .....................................
User’s Manual ECM-3711 Series User’s Manual 7 2.4.17 ATX Power Switch Co nnector (JPS1) ....................................................................................... 42 2.4.18 Power Connector (JPWR1)......................................
ECM-3711 Series 8 ECM-3711 Series User’s Manual 1. CMOS BATTERY HAS FAILED ........................................................................................................ .9 1 2. CMOS CHECKSU M ERROR ........................................
User’s Manual ECM-3711 Series User’s Manual 9 1. Getting Started 1.1 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges.
ECM-3711 Series 10 ECM-3711 Series User’s Manual 1.3 Document Amendment History Revision Date By Comment 1st Aug. 2006 Jason Liu Initial Release.
User’s Manual ECM-3711 Series User’s Manual 11 1.4 Manual Objectives This manual describes in detail the Ev alue Technology ECM- 3711 Single Board.
ECM-3711 Series 12 ECM-3711 Series User’s Manual 1.5 System Specifications System CPU Onboard VIA Eden V4 1 GHz BIOS Award 512 KB Flash BIOS System Chipset VIA CN700/VT8251 I/O Chip VIA VT1211 System Memory One 200-pin SODIMM supports up to 1 GB DDR2 400/533 SDRAM SSD One CompactFlash Type I/II socket Watchdog Timer Reset: 1~255 min.
User’s Manual ECM-3711 Series User’s Manual 13 Mechanical & Environmental Power Requ irement +5 V @ 4.63 A, +12 V @ 0.53 A, 5 Vsb @ 0.32 A ( with VIA Eden V4 1 GHz & 1 GB DDR2 SDRA M) Power Type ATX Operation Temperature 0~60°C (32~140°F) Operating Humidity 0%~90% relative humidity, non-condensing Size ( L x W ) 45.
ECM-3711 Series 14 ECM-3711 Series User’s Manual 1.6 Architecture Overview 1.6.1 Block Diagram The following block diagram shows the arch itecture and main components of ECM-3721 Series. The following sections provide detail info rmation about the functions provided onboard.
User’s Manual ECM-3711 Series User’s Manual 15 1.6.2 VIA CN700 & VT8251 The CN700 implements a deep In-Order Que ue to improve system performance for multi-threaded software applications. DBI and V4 bus protocol are supported which effectively reduce overall system power cons umption.
ECM-3711 Series 16 ECM-3711 Series User’s Manual • 2D Graphics Engine The CN700 North Bridge's advanced 128-bit 2D graphics engine deliv ers high-speed 2D acceleration for productivity applications.
User’s Manual ECM-3711 Series User’s Manual 17 The VT8251 interfaces to t he companion North Bridge ch ip through the Ultra V-Link interface with up to 1 GB/sec data transferra te. Two 1-Lane PCI Express ports are provided for high-speed peripheral devices.
ECM-3711 Series 18 ECM-3711 Series User’s Manual • Plug and Play functions wit h steerable PCI interrupts The PnP function allows complete steerability of PCI interrupts and integrated peripheral interrupts to system interrupt channel.
User’s Manual ECM-3711 Series User’s Manual 19 1.6.4 VIA VT1636 LVDS Transmitter • Support Single / Dual LV DS Transmitter Function • Compatible with TI A/EIA-644 LVDS Standard • Supports LV.
ECM-3711 Series 20 ECM-3711 Series User’s Manual A hardware monitor engine is built in to m onitor system health. An enhanced 8 bit ADC is built inside. This is exploited to simultaneou sly monitor 8 analog voltages or thermal inputs. The thermal inputs can be defined independently as thermistor or PentiumTM II thermal diode.
User’s Manual ECM-3711 Series User’s Manual 21 The device features next-generation PCI Express interconnect technology. PCI Express is a high-bandwidth, low pin count, serial, inte rconnect techno.
ECM-3711 Series 22 ECM-3711 Series User’s Manual 2. Hardware Configuration.
User’s Manual ECM-3711 Series User’s Manual 23 2.1 Product Overview.
ECM-3711 Series 24 ECM-3711 Series User’s Manual 2.2 Installation Procedure This chapter explains you the instru ctions of how to setup your system. 1. Turn off the power supply. 2. Insert the DIMM module (be careful with t he orientation). 3. Insert all external cables for hard disk, flop py, keyboard, mouse, USB etc.
User’s Manual ECM-3711 Series User’s Manual 25 2.2.1 Main Memory ECM-3711 series provides one 2 00-pin DIMM sockets to support DDR2 SDRAM. The total maximum memory size is 1GB. (Rear Side) Make sure to unplug the power supply before adding or removing DIMMs or other system components.
ECM-3711 Series 26 ECM-3711 Series User’s Manual • Locate the DIMM socket on the board. • Hold two edges of the DIMM module carefu lly. Keep away of touching its connectors. • Align the notch key on the m odule with the rib on the slot. • Firmly press the modules into the socket aut omatically snaps into the mounting notch.
User’s Manual ECM-3711 Series User’s Manual 27 2.3 Jumper and Connector List You can configure your board to match the needs of your applic ation by setting jumpers.
ECM-3711 Series 28 ECM-3711 Series User’s Manual Connectors Label Function Note JAUDIO1 Audio connector 5 x 2 header, pitch 2.0mm JCD1 CD-ROM audio input connector 4 x 1 wafer, pitch 2.0mm JCF1 Compact Flash connector JCOM1 Serial port 1 connector D-sub 9-pin, male JCOM2 Serial port 2 connector 5 x 2 header, pitch 2.
User’s Manual ECM-3711 Series User’s Manual 29 2.4 Setting Jumpers & Connectors 2.4.1 AT/ATX Power Select (JAT1) * Default AT* ATX 2.4.2 Clear CMOS (JCMOS1) * Default Protect* Clear CMOS.
ECM-3711 Series 30 ECM-3711 Series User’s Manual 2.4.3 Audio connector (JAUDIO1) Signal PIN PIN Signal GND 12 11 SPDIF OUT NC 10 9 NC Mic Bias 8 7 Mic-in LIN_R 6 5 LIN_L GND 4 3 GND LINEOUT _R 2 1 LINEOUT_L 2.4.3.1 Signal Description – Audio Connecter (JAUDIO1) Signal Signal Description LINEOUT L/R Left and right speaker out put.
User’s Manual ECM-3711 Series User’s Manual 31 2.4.4 CD-ROM Audio I nput Connector (JCD1) Signal PIN CD_L 4 GND 3 CD_R 2 GND 1 2.4.4.1 Signal Descript ion – CD-ROM Audio I nput Connecter (JCD1) Signal Signal Description CD_R Right CD-IN signal CD_L Left CD-IN signal.
ECM-3711 Series 32 ECM-3711 Series User’s Manual 2.4.5.1 Signal Description – Seri al Port 1 Connecter (JCOM1) Signal Signal Description TxD Serial output. This signal sends serial data to the communication link. The sign al is set to a marking state on hardwa re reset when the transmitter i s empty or when loop mode operation is initiated.
User’s Manual ECM-3711 Series User’s Manual 33 2.4.7 Serial Port Connector in RS-422 Mode (JCOM2) Signal PIN PIN Signal GND 10 9 GND RxD- 8 7 NC TxD+ 6 5 GND NC 4 3 NC RxD+ 2 1 TxD- 2.
ECM-3711 Series 34 ECM-3711 Series User’s Manual 2.4.8.1 Signal Description – Seri al Port 2 Connecter (JCOM2) Signal Signal Description TxD Serial output. This signal sends serial data to the communication link. The sign al is set to a marking state on hardwa re reset when the transmitter i s empty or when loop mode operation is initiated.
User’s Manual ECM-3711 Series User’s Manual 35 2.4.9 General Purpose I/O Connector (JDIO1) Signal PIN PIN Signal GND 10 9 +5V GP17 8 7 GP13 GP16 6 5 GP12 GP15 4 3 GP11 GP14 2 1 GP10 2.4.9.1 Signal Description – Genera l Purpose I/O Connecter (JDIO1) Signal Signal Description GP [10:17] Digital Input/Output Data Bit 0 to Bit 8 2.
ECM-3711 Series 36 ECM-3711 Series User’s Manual 2.4.11 Primary IDE Connector (JIDE1) Signal PIN PIN Signal RESET# 1 2 GND PDD7 3 4 PDD8 PDD6 5 6 PDD9 PDD5 7 8 PDD10 PDD4 9 10 PDD11 PDD3 11 12 PDD12.
User’s Manual ECM-3711 Series User’s Manual 37 2.4.11.1 Signal Description – Pr imary IDE Connector (JIDE1) Signal Signal Description PDA [2:0] IDE Address Bits. These address bits are used to access a regi ster or data port in a device on the IDE bus.
ECM-3711 Series 38 ECM-3711 Series User’s Manual 2.4.12 LCD Inverter Connector (JINV1) Signal PIN +12V 1 GND 2 ENBKL 3 VR 4 +5V 5 Note: For inverters with adjustable Backlight f unction, it is possible to control the LCD brightness through the VR signal controlled by JVR1 .
User’s Manual ECM-3711 Series User’s Manual 39 2.4.13 IrDA Connector (JIR1) Signal PIN IRTX 5 GND 4 IRRX 3 NC 2 +5V 1 2.4.13.1 Signal Description – IrDA Connector (JIR1) Signal Signal Descriptio.
ECM-3711 Series 40 ECM-3711 Series User’s Manual 2.4.14 PS/2 Keyboard & Mouse Connector (JKB1) Signal PIN PIN Signal MDAT 6 5 KDAT GND 4 3 +5V KCLK 2 1 MCLK 2.
User’s Manual ECM-3711 Series User’s Manual 41 2.4.16 LVDS Connector (JLVDS1) Signal PIN PIN Signal +5V 2 1 +3.3V +5V 4 3 +3.3V I 2 C_DAT 6 5 I 2 C_CLK GND 8 7 GND Txout0 10 9 Txout1 Txout0# 12 11.
ECM-3711 Series 42 ECM-3711 Series User’s Manual 2.4.17 ATX Pow er Switch Connector (JPS1) Signal PIN GND 2 PW_BN 1 2.4.18 Pow er Connector (JPWR1) PIN Signal 1 +12V 2 GND 3 GND 4 +5V.
User’s Manual ECM-3711 Series User’s Manual 43 2.4.19 Single Power Select (JSUS1) Signal PIN PWR_ON 1 +5V 2 VCCSB 3 Note: The default sets 2-3 closed for single power use d. 2.4.20 USB Connector 0, 1, 2 & 3 (JUSB1, JUSB2 ) Signal PIN PIN Signal +5V 1 2 GND D1-/D3- 3 4 GND D1+/D3+ 5 6 D0+/D2 + GND 7 8 D0-/D2- GND 9 10 +5V 2.
ECM-3711 Series 44 ECM-3711 Series User’s Manual 2.4.21 VGA Connector (JVGA1) Signal PIN Signal 6 GND RED 1 11 NC 7 GND GREEN 2 12 DAT 8 GND BLUE 3 13 HSYNC 9 VCC NC 4 14 VSYNC 10 GND GND 5 15 DCK 2.4.21.1 Signal Description – VGA Connecter (JVGA1) Signal Signal Description HSYNC CRT horizontal sync hro nisation output.
User’s Manual ECM-3711 Series User’s Manual 45 2.4.22 LCD Backlight Brightness Adjustment Connector (JVR1) Signal PIN +5V 3 VR 2 GND 1 VCC JINV1 pin 4 JVR1 1 2 3 Variation Resistor (Recommended: 4.
ECM-3711 Series 46 ECM-3711 Series User’s Manual 2.5 Audio / USB Daughter Board User’s Guide 2.5.1 Jumper and Connector Layout 2.5.2 Jumper and Connector List Jumpers Label Function Note JP6 Line .
User’s Manual ECM-3711 Series User’s Manual 47 2.5.3 Setting Jumper and Connector Line out / Speaker out Select (JP6) 2.54mm USB 1.1/2.0 Connector 1 (JP1) Line Out* Speaker Out Signal PIN PIN Sign.
ECM-3711 Series 48 ECM-3711 Series User’s Manual 3. BIOS Setup.
User’s Manual ECM-3711 Series User’s Manual 49 3.1 Starting Setup The AwardBIOS™ is immediately activated when you first power on the computer. The BIOS reads the system information contai ned in the CMOS and begins the process of checking out the system and configuring it.
ECM-3711 Series 50 ECM-3711 Series User’s Manual 3.2 Using Setup In general, you use the arrow keys to highlight items, press <Enter> to select, use the PageUp and PageDown keys to change entries, pr ess <F1> for help and press <Esc> to quit.
User’s Manual ECM-3711 Series User’s Manual 51 • To Display a Sub Menu Use the arrow keys to move the cursor to the sub menu you want. Then press <Enter>.
ECM-3711 Series 52 ECM-3711 Series User’s Manual 3.5 Main Menu Once you enter the AwardBIOS™ CMOS Set up Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and two exit choices. Use the arrow keys to select among the items and press <Ent er> to accept and enter the sub-menu.
User’s Manual ECM-3711 Series User’s Manual 53 3.5.1 Standard CMOS Features The items in Standard CMOS Se tup Menu are divided into few categories. Each category includes no, one or more than one setup items. Use the arrow ke ys to highlight the item and then use the <PgUp> or <PgDn> keys to select the value you want in each item.
ECM-3711 Series 54 ECM-3711 Series User’s Manual 3.5.1.2 IDE Adapter Setup The IDE adapters control the ha rd disk drive. Use a s eparate sub menu to configure each hard disk drive.
User’s Manual ECM-3711 Series User’s Manual 55 3.5.2 Advanced BIOS Features This section allows you to configure your system for basic oper ation. You have the opportunity to select the syst em’s default speed, boot-up seq uence, keyboard operation, shadowing and security.
ECM-3711 Series 56 ECM-3711 Series User’s Manual 3.5.2.2 Hard Disk Boot Priority This item allows you to select the Hard Disk device boot up priority. Item Description Pri.Master Boot up from IDE Primary Master Hard Disk Pri.Slave Boot up from IDE Primary Slave Hard Disk Sec.
User’s Manual ECM-3711 Series User’s Manual 57 3.5.2.4 CPU L1 & L2 Cache This item allows you to enable the CPU L1 & L2 cache to speed up memory access. However, it depends on CPU design. Item Description Enabled Enable cache Disabled Disable cache 3.
ECM-3711 Series 58 ECM-3711 Series User’s Manual 3.5.2.11 Typematic Rate Setting Key strokes repeat at a rate determined by the keyboard controller. When enabled, the typematic rate and typematic delay can be selected. Item Description Enabled Enable typematic rate/delay setting Disabled Disable typematic rate/delay setting 3.
User’s Manual ECM-3711 Series User’s Manual 59 3.5.2.18 Full Screen LOGO Show If the BIOS had the full screen logo in it, this item could allow enable/ disable the full screen logo show on display. Item Description Enable Enable full screen logo show Disable Disable full screen logo show 3.
ECM-3711 Series 60 ECM-3711 Series User’s Manual 3.5.3 Advanced Chipset Features This section allows you to configure the system based on the specif ic features of the installed chipset. This chipset manages bus speeds and access to system memory resources, such as DRAM and the external ca che.
User’s Manual ECM-3711 Series User’s Manual 61 3.5.3.1 DRAM Clock/Drive Control This section can set the DRAM clock/driver timing. Item Options Description DRAM Clock By SPD 100NHz 133 MHz 166 MHz.
ECM-3711 Series 62 ECM-3711 Series User’s Manual 3.5.3.2 AGP & P2P Bridge Control This item stores the onboard AGP and P2P functi on information. The reference table is as below. Item Options Description AGP Aperture Size 32M, 64M, 128M, 256M, 512M, 1G Select the size of Accele rated Graphics Port (AGP) aperture.
User’s Manual ECM-3711 Series User’s Manual 63 3.5.3.3 CPU & PCI Bus Control Item Options Description PCI Master 0 WS Write Enabled Disabled To write PCI bus while zero wait state is executed. PCI Delay Transaction Enabled Disabled This feature is used to meet the latency of PCI cycles to and from the ISA bus.
ECM-3711 Series 64 ECM-3711 Series User’s Manual 3.5.3.4 Memory Hole This feature allows you to create a memory hole. Item Description Disabled 512K-640K 15M-16M 14M-16M When this item is enabled, ISA ROM will be mapped to 15-16M area and also support legacy ISA devices.
User’s Manual ECM-3711 Series User’s Manual 65 3.5.4 Integrated Peripherals Use this menu to specify your se ttings for integrated peripherals. 3.5.
ECM-3711 Series 66 ECM-3711 Series User’s Manual Item Options Description SATA Controller Enabled Disabled The chipset contains a SATA IDE interface with support for two IDE channe ls. Select Enabled to activate the primary IDE interface (Channel0).
User’s Manual ECM-3711 Series User’s Manual 67 3.5.4.2 VIA OnChip PCI Device Item Options Description AC97 Audio Controller Auto Disabled This item allows you to decide to enable/disable the VIA chi pset family to support AC97 Audio.
ECM-3711 Series 68 ECM-3711 Series User’s Manual 3.5.4.3 Super IO Device Item Options Description Onboard Serial Port 1 Onboard Serial Port 2 Disable 3F8/IRQ4 2F8/IRQ3 3E8/IRQ4 2E8/IRQ3 AUTO Select an address and corre sponding interrupt for the first and second serial ports.
User’s Manual ECM-3711 Series User’s Manual 69 3.5.4.4 USB Device Setting Item Options Description USB 1.0 Controller Enabled Disabled This item is to enable or disable the USB 1.0 Controller. USB 2.0 Controller Enabled Disabled This item is to enable or disable the USB 2.
ECM-3711 Series 70 ECM-3711 Series User’s Manual 3.5.5 Power Management Setup The Power Management Setup allows you to conf igure you system to most effectively save energy while operating in a manner consistent with your own style of computer use. 3.
User’s Manual ECM-3711 Series User’s Manual 71 3.5.5.5 Suspend Mode This setting defines the number of minutes before the system enters "suspend mode", the deepest level of system inactivity shutdown.
ECM-3711 Series 72 ECM-3711 Series User’s Manual 3.5.5.12 Wakeup Event Detect Item Option Description PS2KB Wakeup Select Hot Key Password Allows you to select the method of PS2KB wake up PS2KB Wake.
User’s Manual ECM-3711 Series User’s Manual 73 3.5.6 PnP / PCI Configuration This section describes configur ing the PCI bus system. PCI, or P ersonal C omputer I nterconnect, is a system which allows I/O dev ices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components.
ECM-3711 Series 74 ECM-3711 Series User’s Manual 3.5.6.4 IRQ Resource When resources are controlled manually, a ssign each system interrupt a type, depending on the type of device using the interrupt. This item allows you to determine the IR Q assigned to the PCI bus or reserved.
User’s Manual ECM-3711 Series User’s Manual 75 3.5.7 PC Health Status This section shows the status of your CPU..
ECM-3711 Series 76 ECM-3711 Series User’s Manual 3.5.8 Frequency / Voltage Control This menu specifies your setti ng for frequency/voltage control. 3.5.8.1 CPU Clock Ratio: This item allows you to select the CPU clock ratio. The choices: 6X 3.5.8.2 Auto Detect PCI Clk This item allows you to enable or disable detecting PCI clock automatically.
User’s Manual ECM-3711 Series User’s Manual 77 3.5.9 Load Fail-Safe Defaults Use this menu to load the B IOS default values for the mini mal/stable performance for your system to operate. Press <Y> to load the BIOS default values for the most stable, minimal-performance system operations.
ECM-3711 Series 78 ECM-3711 Series User’s Manual 3.5.11 Set Supervisor / User Passw ord You can set either supervisor or user password, or both of them. Supervisor Password: able to enter/c hange the options of setup menus. User Password: able to enter but no right to change the options of setup menus.
User’s Manual ECM-3711 Series User’s Manual 79 When a password has been enabled, you will be prom pted to enter it every time you try to enter Setup.
ECM-3711 Series 80 ECM-3711 Series User’s Manual 3.5.12 Save & Exit Setup Save CMOS value changes to CMOS and exit setup. Enter <Y> to store the selection made in the menus in CMOS, a special section in memory that stays on after turning the system off.
User’s Manual ECM-3711 Series User’s Manual 81 4. Drivers Installation Note : Installation procedures and scr een shots in this section are for your reference and may not be exactly the same as shown on your screen.
ECM-3711 Series 82 ECM-3711 Series User’s Manual 4.1 Install Chipset Driver (For VIA CN700) Insert the Supporting CD-ROM to CD-ROM drive, and it should show the index page of Evalue’s products automatically. If not, locate Index.htm and choose the product from the menu left, or link to Driver_ChipsetVIACN700.
User’s Manual ECM-3711 Series User’s Manual 83 Step 6. Click Next . Step 7. Click Finish to restart the PC..
ECM-3711 Series 84 ECM-3711 Series User’s Manual 4.2 Install Display Dri ver (For VIA CN700) Insert the Supporting CD-ROM to CD-ROM drive, and it should show the index page of Evalue’s products automatically. If not, locate Index.htm and choose the product from the menu left, or link to Driver_DisplayVIACN700 .
User’s Manual ECM-3711 Series User’s Manual 85 4.3 Install Audio Driver (For VIA VT1616) Insert the Supporting CD-ROM to CD-ROM drive, and it should show the index page of Evalue’s products automatically. If not, locate Index.htm and choose the product from the menu left, or link to Driver_AudioVIAVT1616.
ECM-3711 Series 86 ECM-3711 Series User’s Manual 4.4 Install Ethernet Driver (For Realtek RTL8111B) Insert the Supporting CD-ROM to CD-ROM drive, and it should show the index page of Evalue’s products automatically. If not, locate Index.htm and choose the product from the menu left, or link to D:Driver_GigabitRealtek RTL8111B .
User’s Manual ECM-3711 Series User’s Manual 87 5. Measurement Drawing.
ECM-3711 Series 88 ECM-3711 Series User’s Manual (Unit: mm).
User’s Manual ECM-3711 Series User’s Manual 89 Appendix A: BIOS Revisions BIOS Rev. New Features Bugs/Problems Solved Known Problems.
ECM-3711 Series 90 ECM-3711 Series User’s Manual Appendix B: AWARD BIOS POST Messages.
User’s Manual ECM-3711 Series User’s Manual 91 Overview During the Power On Self-Test (POST), if t he BIOS detects an error requiring you to do something to fix, it will either sound a beep code or display a message.
ECM-3711 Series 92 ECM-3711 Series User’s Manual 5. DISPLAY SWITCH IS SET INCORRECTLY Display switch on the motherboard can be set to either monochrome or co lor.
User’s Manual ECM-3711 Series User’s Manual 93 12. Invalid EISA Configuration PLEASE RUN EISA CONFIGURATION UTILITY The non-volatile memory containing EISA configuration information was programmed incorrectly or has become corrupt. Re-run EISA configuration utility to correctly program the memory.
ECM-3711 Series 94 ECM-3711 Series User’s Manual 20. PRESS A KEY TO REBOOT This will be displayed at the bottom screen when an error occurs that requires you to reboot.
User’s Manual ECM-3711 Series User’s Manual 95 27. Wrong Board In Slot PLEASE RUN EISA CONFIGURATION UTILITY The board ID does not match the ID stor ed in the EISA non-volatile memory. Note: When either of these errors appears, the system will boot in ISA mode, which allows you to run t he EISA Configur ation Utility.
ECM-3711 Series 96 ECM-3711 Series User’s Manual 40. POST Codes POST (hex) Description CFh Test CMOS R/W functionality. C0h Early chipset initialization: -Disable shadow RAM -Disable L2 cache (socket 7 or below) -Program basic chipset registers C1h Detect memory -Auto-detection of DRAM size, type and ECC.
User’s Manual ECM-3711 Series User’s Manual 97 POST (hex) Description 15h Reserved 16h Initial Early_Init _Onboard_Generator switch. 17h Reserved 18h Detect CPU information includ ing brand, SMI type (Cyrix or Intel) and CPU level (586 or 686). 19h Reserved 1Ah Reserved 1Bh Initial interrupts vector table.
ECM-3711 Series 98 ECM-3711 Series User’s Manual POST (hex) Description 2Dh 1. Initialize multi-language 1. Put information on screen display, including Award title, CPU type, CPU speed …. 2Eh Reserved 2Fh Reserved 30h Reserved 31h Reserved 32h Reserved 33h Reset keyboard except Winbond 977 series Super I/O chips.
User’s Manual ECM-3711 Series User’s Manual 99 POST (hex) Description 51h Reserved 52h Test all memory (clear all extended memory to 0) 53h Reserved 54h Reserved 55h Display number of proce ssors (multi-processor platform) 56h Reserved 57h 1. Display PnP logo 2.
ECM-3711 Series 100 ECM-3711 Series User’s Manual POST (hex) Description 73h (Optional Feature) Enter AWDFLASH.EXE if : -AWDFLASH is found in floppy drive. -ALT+F2 is pressed 74h Reserved 75h Detect & install all IDE dev ices: HDD, LS12 0, ZIP, CDROM….
User’s Manual ECM-3711 Series User’s Manual 101 POST (hex) Description 94h 1. Enable L2 cache 1. Program boot up speed 2. Chips et final initialization. 3. Power management final initializ ation 4. Clear screen & display summary table 5. Program K6 write allocation 6.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Evalue Technology ECM-3711 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Evalue Technology ECM-3711 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Evalue Technology ECM-3711 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Evalue Technology ECM-3711 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Evalue Technology ECM-3711, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Evalue Technology ECM-3711.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Evalue Technology ECM-3711. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Evalue Technology ECM-3711 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
