Manuale d’uso / di manutenzione del prodotto Drying Tumbler Part No. 70400401R2 del fabbricante Alliance Laundry Systems
Vai alla pagina of 24
Operation/Pr ogramming/Maintenance www .comlaundry .com www .comlaundry .com Drying T umblers 120 Pound Capacity 170 Pound Capacity Refer to Pa ge 3 for Model Identif ication Part No. 70400401R2 August 2007 K eep These Instructions f or Future Refer ence.
.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 70400401 1 Installation must conf orm with local code s or in the absence of lo cal codes with: In the U .S.A. , installation must conf orm to the latest edit ion of the American Nati onal Standard Z223.
© Copyright 2007, Alliance Laundry Systems LLC All rights reserv ed. No part of the cont ents of this book may be reproduced or transmitted in an y form or by an y means without the e xpressed written consent of the publisher . © Copyright, Alliance Laundry Systems LLC – D O NO T COPY or TRANSMIT 2 70400401 Ta b l e o f Contents Introduction .
3 70400401 © Copyright, Alliance Laundr y Systems LLC – DO NOT COPY or TRANSMIT Intr oduction Model Identification Information in this manual is applicable to these models.
Introd uction 70400401 4 © Copyright, Alliance Laundr y Systems LLC – DO NOT COPY or TRANSMIT Serial Plate Location When calling or writing for information about your product, be sure to mention model an d serial numbers. Model and serial numbers are found on serial plate on rear of machine.
5 70400401 © Copyright, Alliance Laundr y Systems LLC – DO NOT COPY or TRANSMIT Safe ty Inf ormation Explanation of Safet y Messages Throughout this manual and on machine decals, you will find precauti onary statements (“D ANGER, ” “W ARNING, ” and “CA UTIO N”) followed b y spe cific instructions.
Sa fe ty In for ma t io n 70400401 6 © Copyright, Alliance Laundr y Systems LLC – DO NOT COPY or TRANSMIT Impor tant Safety Instructions Sa ve These Instructions 1. Read all instructions before using the tumbler . 2. Refer to the GR OUNDING INSTRUCTIONS in the Installation Manual for the proper grounding of the tumbler .
Safety Information 7 70400401 © Copyright, Alliance Laundr y Systems LLC – DO NOT COPY or TRANSMIT 23. Remov e laundry immediately after tumbler stops. 24. Always read and follo w manufacturer’ s instructions on package s of laundry and cleanin g aids.
70400401 8 © Copyright, Alliance Laundr y Systems LLC – DO NOT COPY or TRANSMIT Operation Emergenc y Stop Button on CE Models All CE appro ved OPL tumblers are f actory equipped with an emergenc y stop button located on the front panel. Refer to Fi g u re 2 .
Operation 9 70400401 © Copyright, Alliance Laundr y Systems LLC – DO NOT COPY or TRANSMIT Contr ol Instructions Figure 3 Dual Digital Timer Control RQ Control Suffix 1. Select HIGH, MED, LO W or NO HEA T by turning the temperature knob . 2. Set the HEA T TIME for the number of minutes (from 0-60) desired.
Operation 70400401 10 © Copyright, Alliance Laundr y Systems LLC – DO NOT COPY or TRANSMIT T o Program a Short T est Cycle: 1. Unplug machine po wer cord. 2. Write do wn machine cont rol dip swi tch settings, then set them all to th e of f position.
Operation 11 70400401 © Copyright, Alliance Laundr y Systems LLC – DO NOT COPY or TRANSMIT Diagnostic Micr oprocessor Contr o l General Operation The Diagno stic Micropro c essor Control (DMP) is designed to ma nage the drying and cooling cycles of the tumbler .
Operation 70400401 12 © Copyright, Alliance Laundr y Systems LLC – DO NOT COPY or TRANSMIT DMP OPL Models RD Control Suffix Description of the OPL Control Panel Refer to Fi g u re 5 . Figure 5 TMB1956N 1 ST ART . Star ts or resumes the current program or cycle .
Operation 13 70400401 © Copyright, Alliance Laundr y Systems LLC – DO NOT COPY or TRANSMIT DMP OPL Features DIP Switch Settings The DMP has an 8 position DIP switch bank that is accessible from the back of the control board.
Operation 70400401 14 © Copyright, Alliance Laundr y Systems LLC – DO NOT COPY or TRANSMIT Programming 1. Set DIP switch #8 to the ON position. 2. Select the desired program number to change. The LED should be flashing. 3. Select DR Y TIME. Set the time with the Up/ Do wn arro ws.
Operation 15 70400401 © Copyright, Alliance Laundr y Systems LLC – DO NOT COPY or TRANSMIT Rotation Sensor The rotation sensor must “read” the ke y on the bask et shaft or pulley . The senso r must be set approximately 1/4 inch from the k ey o r pulle y .
Operation 70400401 16 © Copyright, Alliance Laundr y Systems LLC – DO NOT COPY or TRANSMIT T ermination of Flame The flame will go out when po wer is removed from ignition control. The ignition control will turn of f the gas v alve and enter Standb y Mode.
Operation 17 70400401 © Copyright, Alliance Laundr y Systems LLC – DO NOT COPY or TRANSMIT Diagnostic LED (DGN LED) / Err o r Codes The Diagnostic LED or DGN LED is located by the po wer connector on the ig nition control. Refer to Fi g u re 6 . The Diagnostic LED will indicate the status of the ignition control.
70400401 18 © Copyright, Alliance Laundr y Systems LLC – DO NOT COPY or TRANSMIT Maintenance Daily 1. Inspect the area surrounding tumblers, remov e all combustible materials, including l int, before operating the machines. 2. Check c ylinder for foreign objects to a void damage to clothing and equipment.
Maintenance 19 70400401 © Copyright, Alliance Laundr y Systems LLC – DO NOT COPY or TRANSMIT Monthly 1. Remov e lint and debris from inside exhau st duct to maintain proper airflo w and a void o verheating. a. Remov e external duct and duct access co vers, if present.
Maintenance 70400401 20 © Copyright, Alliance Laundr y Systems LLC – DO NOT COPY or TRANSMIT Daily Maintenance Monthly Maintenance T o reduce the risk of electric shoc k, fire, explosion, serious injury or death: • Disconnect electric po wer to the tumbler before servicing.
Maintenance 21 70400401 © Copyright, Alliance Laundr y Systems LLC – DO NOT COPY or TRANSMIT Quarterly Maintenance Bi-Annually Maintenance Use a v acuum to clean air vents on driv e mo tors. Use a v acuum to clean lint from rear limit thermostat cover .
70400401 22 © Copyright, Alliance Laundr y Systems LLC – DO NOT COPY or TRANSMIT Bef ore Y ou Call f or Ser vice Customer Ser vice If literature or replacement parts are required, contact the sourc.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Alliance Laundry Systems Drying Tumbler Part No. 70400401R2 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Alliance Laundry Systems Drying Tumbler Part No. 70400401R2 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Alliance Laundry Systems Drying Tumbler Part No. 70400401R2 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Alliance Laundry Systems Drying Tumbler Part No. 70400401R2 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Alliance Laundry Systems Drying Tumbler Part No. 70400401R2, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Alliance Laundry Systems Drying Tumbler Part No. 70400401R2.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Alliance Laundry Systems Drying Tumbler Part No. 70400401R2. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Alliance Laundry Systems Drying Tumbler Part No. 70400401R2 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
