Manuale d’uso / di manutenzione del prodotto EN9110 del fabbricante Envision Peripherals
Vai alla pagina of 28
EN9110 EN9110 19” LCD Monitor User’s Manua l By Envision Peripher als, In c. www.envisionm onitor .com.
EN9110 1 Before oper ating the moni tor, ple ase read this m anual thor oughly . T his manual should be r etained for fut ure ref erence. FCC Clas s B R ad io Frequ en cy Interf eren ce Statemen t WA .
EN9110 2 ! Do not use the monitor near w ater, e.g. near a bathtub, w ashbowl, kitchen sink, laundry tub, sw imming pool or in a w et basement. ! Do not place the monitor on an unstabl e cart, stand, or table. If the monitor falls, it can injur e a person and cause serious damage to the appliance.
EN9110 3 • For maximu m protection, re package your monit or as it was originall y packed at the factory . • To keep the monitor looking new, periodically clean it w ith a soft cloth. Stubbor n stains may be removed w ith a cloth lightly dampened w ith a mild deterg ent solution.
EN9110 4 The follow ing symptoms are norm al wi th LCD monitor and do not indicate a problem. NOT ES • Due to the nature of the fluorescent light, the screen may fli cker during initial use. T urn o ff the Pow er Sw itch and then turn it on again to make sure the flicker disappears.
EN9110 5 INSTA LLA TION INSTRUCTIONS SWIVEL BA SE Install Remove Figure 1 Install ing and Remov i ng the Swiv el Base POWERCORD Pow er So urce: 1. M ake sure that the pow er cord is the correct ty pe require d in your ar ea.
EN9110 6 PREPA RING TO INST A LL T HE CA BL ES 1. Remove the w all mounting hole cover. 2. Remove the cable cov er. INSTA LLA T IONS INSTRUCTIONS (cont).
EN9110 7 CA BLE CONNEC T IONS 1 – Connect the DC -jack pow er cable into DC -IN connector on the back of the monito r. 2. Connect one en d of the 15-pin D -Sub cable to the back of the monitor and connect the other end to the c omputer’s D -Sub port .
EN9110 8 Pre pa r ing T o Instal l The Optional Wall Mount A rm (Not Included) CONNECTIONS Thi s monitor can be attached to a w all mounting arm y ou can purchase separately from Ergotron (w ww .ergotron.com). T urn the pow er OFF then dis- connect the cables from the moni tor before per forming the procedur e below .
EN9110 9 A ttaching The Optiona l Wa ll Mount A rm (not suppl ied) Follow thes e steps to finish instal ling the w all mounting arm: 1. Place the wall mounting arm o nto the back of the monitor. Line up the holes of the ar m wi th the holes in the back of the moni tor.
EN9110 10 INSTA LLA TION INSTRUCTIONS • For optimal view ing it is recommended to look at the full face of the monitor, the n adjust the monitor’s angle to your ow n preference. • Hold the stand so you do not topple the monitor w hen you change the monitor’s angl e.
EN9110 11 OPERA TING INSTR UCTIONS Press the pow er button to turn the monitor on or off. Th e other control buttons are located on the side of the mo nitor (S ee Figure 4) . By changi ng these settings, the pictur e can be adjusted to y our personal pr eferences.
EN9110 12 FRONT PA NEL CONTROL • Pow er Button : Press this button t o switch the mo nitor’s pow er ON or OFF. • MENU / ENTER : Activate O SD menu w hen OSD is OFF or activate /de-activate adjustment function w hen O SD is ON or E xit O SD menu w hen in Brightne ss/Contrast OSD status.
EN9110 13 1. Press the M ENU-but ton to activate the OSD window . See figure 5. 2. Press or to select the desired function. See figure 5. 3. Press the M ENU-but ton again to activate the highli ghted function. 4. Press or to adjust the selected function.
EN9110 14 Below desc ribes the function of each OS D icon. 1. Contra st Adjust the picture contrast. 2. Brightness Adjust the picture brightness. 3. Input Selected Input Signal source selected ( select Analog or Digital input s ource ) 4. Focus Adjust pictur e Focus (available in Analog mode only) .
EN9110 15 Plug & Pla y D DC1/2B Featur e This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STA NDARD. It allow s the mon itor to inform the h ost system of its identity and, dependi ng on the lev el of DDC us ed, communicate additi onal information about its display capabilities.
EN9110 16 TECHNIC A L SUPPORT (FA Q) Problem & Question Possible Solution Pow er LED is not on *Check if the Power Sw itch is in the ON position *Pow er Cord s hould be connected No Plug & P l.
EN9110 17 Screen image i s not centered or sized properl y. *Adjust pix el frequency ( CLOCK) and FOCU S or press hot-key (AUTO) Picture has color defects (w hite does not look w hite) *Adjust RG B color or sele ct a pre-set color temperature fr om OSD.
EN9110 18 NO SIGNA L 1. Check that the signal- cable is properly connected , If the connector is loose, tighten the connector’ s screws. 2. Check the signal-cable’ s connection pins for damage. INP UT NOT SU PPOR T Your computer has been set to unsuitabl e display mode ,set the compute r to display mode given in the following t able.
EN9110 19 1024 × 768 75Hz 1024 × 768 85Hz 1280 × 1024 60Hz 1280 × 1024 75Hz 1280 × 1024 85Hz 1152 × 864 75Hz 1280 × 960 60Hz 1280 × 960 85Hz 640 × 480 67Hz 832 × 624 75Hz 640 × 400 56Hz NOT.
EN9110 20 FOR FI RST TIM E INS T A LL : This is a Plug & Play LCD monitor. Turn off the PC then connect the cables. Pow er on the PC and it w ill automatically detect y our new monit or. The W indow s Operating s yst em w ill automati cally insta ll a plug & play driv er for it.
EN9110 21 A PPENDIX SPECIF ICA TIO NS Driving system TFT Color LCD LCD Pan el Siz e 48cm(19.0") Pix el pitch 0.294mm( H ) x 0.294mm( V ) View able angle 170 ° (H) 17 0 ° (V ) Response time 25 ms ( T ypical ) Video R,G,B A nalog Interface Input Separ ate Sy nc.
EN9110 22 Switc h • Au t o Adj us t Key • / Brightness • / Contrast • Powe r Butt on • ME NU / Exi t Ex ternal Controls: Functions • Contras t • Brightness • Input Selected • Focus .
EN9110 23 STANDA RD RESOLUT ION HORIZONT AL FREQUEN CY VE RTICAL FREQUENCY Dos-mode 640 × 400 31.47kHz 70.0Hz Dos-mode 720 x 400 31.47kHz 70.0Hz Dos-mode 720 x 400 31.47kHz 70.0Hz VGA 640 × 480 31.47kHz 60.0Hz 640 × 480 35.00kHz 66.6Hz 640 × 480 37.
EN9110 24 15 6 10 11 15 15 - Pin Co lor Display Signal C able PIN NO. DESCRIPT ION PI N NO. DESCRIPT ION 1. Red 9. +5V 2. Green 10. Detect Cable 3. Blue 11. NC 4. Ground 12. DDC-Serial Data 5. Ground 13. H-Sy nc 6. R-G round 14. V-Sy nc 7. G-G r ound 15.
EN9110 25 8. N.C. 20. TMDS Data 5- 9. TM DS Data 1- 21. TM DS Data 5+ 10. TM DS Data 1+ 22. TM DS Clock Shield 11. TM DS Data 1/3 Shie ld 23. TM DS Cl ock + 12.
EN9110 26 WARRAN TY STATEMENT for Envision C olor Monit ors Inc luding t hos e Sold within North Am er ic a as Spec ified Env ision Peripherals, Inc. warrants this product to be fr ee from defects in material and w orkmanship for a period of thre e (3) y ears after the original date of consumer purchase.
EN9110 27 ! Improper envir onment ! Ex ces siv e or inadeq uate heating or air conditioning or el ectrical pow er failures, surges, or ot her irregularities This three-y ear limited war ranty does not.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Envision Peripherals EN9110 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Envision Peripherals EN9110 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Envision Peripherals EN9110 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Envision Peripherals EN9110 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Envision Peripherals EN9110, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Envision Peripherals EN9110.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Envision Peripherals EN9110. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Envision Peripherals EN9110 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
