Manuale d’uso / di manutenzione del prodotto MHVFB10LP del fabbricante Enerco
Vai alla pagina of 16
Installation instructions and Owner’s Manual 1 ENER CO GR O UP , INC., 4 560 W . 1 60 TH ST ., CLEVELAND, OHIO 4 4 1 3 5 · 2 1 6-9 1 6-3 000 W ARNING: If the information in this manual is not followed exactly , a fire or explosion may result causing property damage, personal injury , or loss of life.
2 Installation instructions and Owner’s Manual This appliance may be installed in an aftermarket* permanently manufactured (mobile) home, where not prohibited by local codes.This appliance is only for use with the type of gas indicated on the rating plate.
Installation instructions and Owner’s Manual 3 Product Features Figure 1 SAFETY DEVICE This heater has a pilot with an Oxygen Depletion Sensor (ODS) safety shut off system. The ODS/pilot shuts off the heater if there is not enough fresh air . IGNITION SYSTEM PIEZO: MHVFB10LP – The heater is equipped with a piezo manual ignitor .
4 Installation instructions and Owner’s Manual 1. Find the volume of the space by multiplying room length x width x height. Example: S pace size 18ft (length) x 18f t. (width) x 8f t. (height) = 2592 If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of the sp ace.
Installation instructions and Owner’s Manual 5 Code NFP A 54/ ANSI Z223.1, Section 5.3, Air for Com- bustion and V entilation for required size of ventilation grills or ducts.
6 Installation instructions and Owner’s Manual Figure 5 Removing Front Panel of Heater 1. Remove three screws on bottom front of front panel. 2. Pull bottom of front panel forward, then down (see figure 6) Figure 6 Attaching Mounting Bracket to W all Use holes on each end of mounting bracket to attach bracket to wall.
Installation instructions and Owner’s Manual 7 1. Locate two horizontal slots on back pane of heater (see figure 19). 2. Place heater onto mounting bracket. Slide horizontal slots onto stand-out tabs on mounting bracket. Figure 9 Installing Bottom Mounting Screws 1.
8 Installation instructions and Owner’s Manual run correctly . IMPORT ANT : Hold pressure regulator with wrench when connecting it to gas piping and/or fittings. CHECKING GAS CONNECTIONS W ARNING: T est all gas piping and connections for leaks after inst alling or servicing.
Installation instructions and Owner’s Manual 9 Figure 13 Figure 14 FOR YOUR SAFETY READ BEFORE LIGHTING W ARNING: If you do not follow these instructions exactly , a fire or explosion may result causing property damage, personal injury or loss of life.
10 Installation instructions and Owner’s Manual Figure 16 CAUTION: Do not try to adjust heating level by using equipment shutoff valve. W ARNING: When running heater, set control knob at “LO” or “HI” locked positions.
Installation instructions and Owner’s Manual 11 Make sure grille guard is in place before running heater . If screen or grille guard is removed for servicing it must be replaced prior to operating the heater . W ARNING: Failure to keep the primary air opening(s) of the burner(s) clean may result in sooting and property damage.
12 Installation instructions and Owner’s Manual TROUBLESHOOTING NOTE: All troubleshooting items are listed in order of operation and likely occurrence. W ARNING: Only a qualified service person should service and repair heater . CAUTION: Never use a wire needle, or similar object to clean ODS/pilot.
Installation instructions and Owner’s Manual 13 TROUBLESHOOTING W ARNING: If you smell gas: • Shut off gas supply • Do not try to light any appliance • Do not touch any electrical switch; do not use any phone in your building • Immediately call you gas supplier from a neighbor’s phone.
14 Installation instructions and Owner’s Manual REPLACEMENT P ARTS Note: use only original replacement parts. This will protect you warranty coverage for parts replaced under warranty . P ARTS UNDER W ARRANTY Contact authorized dealer from whom you pur- chased this product.
Installation instructions and Owner’s Manual 15 ITEM P A R T N O . DESCRIPTION QTY . MHVFB10LP 1 70300 Cabinet assembly 1 1-1 70595 Cabinet T op Panel 1 1-2 70592 Cabinet Right Panel 1 1-3 70593 Cab.
16 Installation instructions and Owner’s Manual ENER CO GR OUP , INC., 4 560 W . 1 60TH ST., CLEVELAND, OHIO 44 1 3 5 216-881-5500 T oll Fr ee Number 1-800-2 5 1-000 1 www .mrhea ter .com Mr . Heater is a r egistered tr ademarks of Ener co Gr oup, Inc.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Enerco MHVFB10LP è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Enerco MHVFB10LP - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Enerco MHVFB10LP imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Enerco MHVFB10LP ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Enerco MHVFB10LP, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Enerco MHVFB10LP.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Enerco MHVFB10LP. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Enerco MHVFB10LP insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
